Beko DW603 User manual

On/Off Button
Tablet Detergent Indicator
Salt Level Indicator Light
Time Delay Indicator
Programme Indicator Light
Start / Stop Indicator Light
Programme Selection Button
Half Load / Tablet Detergent Button
Start / Stop Button
Time Delay Button
Half Load Indicator Light Rinse Aid Indicator Light
DW603 Programme Chart and Quick Reference Guide
Before starting, it is essential that you carefully read right through the Installation
& Operation Instruction booklet before plugging in to the mains socket.
* Values declared on the product or in the operating instruction booklet / programme chart and quick
reference card supplied with the product are obtained in tests performed under controlled laboratory
conditions and these tests are as defined in relevant standards. These figures may vary depending on how soiled
the dishes are, the water hardness level and other factors. Temperature changes exceeding 15°C may also effect
these figures.
** Reference programme for the Testing Institute and energy labelling. Testing programme: Eco 50°C as
compliant to EN 50242 international norms.
*** Due to continual improvement through research & design, specifications and design may change without
prior notice.
Programme
symbols and
temperatures
Programme
selection
Detergent
compartment
A=25 cm³ / 15 cm³
B=5 cm³
Programme
sequence
Consumption
figures
Water (Litres)
Energy (kWh)
Duration (min)
Pre-wash to rinse
and loosen residue
awaiting full load
then select a
Programme
Most economic
programme for
normally soiled
dishes
Lightly soiled dishes,
A class cleaning
in 58 minutes
Heavily soiled dishes
requiring
hot pre-wash
1**
ECO
50°C
2
PRE-WASH
No Heat
3
RAPID
35°C
4
QUICK & CLEAN
60°C
5
INTENSIVE
70°C
Prewash
Wash
Cold Rinse
Hot Rinse
Drying
End
Prewash
End
Wash
Cold Rinse
Hot Rinse
End
Wash
Cold Rinse
Hot Rinse
Drying
End
14
1,02
165
4,2
-
14
0,79
11,8
30
1,32
11,8
58
17,5
1,67
115
Lightly soiled
dishes
30 minute
programme
A+B A A+BA-
Prewash
Wash
Cold Rinse
Hot Rinse
Drying
End
All manuals and user guides at all-guides.com
all-guides.com

· Push in the on/off button and check that the programme indicator lights come on.
· Check the salt and rinse aid level indicator lights before you start the machine. If necessary add salt and rinse aid.
· Select the required programme by referring to the programme chart.
· Select the desired programme by using the Programme Selection Button.
· You may use Half Load/Combi Tablet button - Delayed Start Button features as necessary.
· Press start/pause/cancel button.
· Close the door then programme starts.
· An audio signal with an interval of 8 seconds warns you to switch your machine off when the selected washing
programme ends. This audible signal will warn you 10 times before it turns off.
! Do not open the dishwasher door whilst the appliance is in operation. However, in case the door is opened while the
machine is working, then a safety mechanism ensures the machine immediately stops. Water may be very hot, so be
careful.
! Care must be taken when opening the door, as steam will escape.
· Press the on/off button after the programme is completed. The indicator lights will go off.
· Unload the baskets - we recommend to turn off the water tap when not in use.
Operating the dishwasher
How to cancel the washing programme
To cancel a programme while the machine is operating:
· Open the door.
! Care must be taken when opening the door, as steam will escape.
· Press and hold start/pause/cancel button for 3 seconds. The start / stop indicator light will start flashing. Close the door.
The machine will drain the water inside the machine for 45 seconds.
· The programme is cancelled when start/stop indicator light goes off. Then, you can choose and start a new programme.
! Depending on the stage of the programme you have cancelled, there may be detergent residue or rinse aid inside the
machine and on the load. Make sure the items in the dishwasher are not used before washing properly.
How to change the washing programme
To change the programme selection while the machine is operating:
· Open the door.
! Care must be taken when opening the door, as steam will escape.
· Press start/pause/cancel button. The indicator light will go off.
· Select the new programme. Press start/pause/cancel button. The indicator light will be on and new programme will start.
! The new programme will NOT start right from the beginning. It will start from the stage last carried out by the previous
programme selection.
Half Load Function
If you want to run your machine without loading it completely, place your dishes into the machine as you desire. Press the
On/Off button to turn on your machine. Press the Half Load/Combi Tablet button after selecting the desired program until
Half Load Indicator lights up, then press start/pause/cancel button and close the door of your machine. With the Half Load
option you can use every part of your lower and upper baskets and you can save by using less water and power.
Tablet Detergent Function
Depending on the hardness level of the tap water, the Tablet Detergent function allows obtaining a better drying
performance from the multi-purpose detergents such as 2in1, 3in1, 4in1, 5in1, etc., called all-in-one tablets. The
programmes in which the tablet detergent function can be enabled are indicated in the Programme Data and Table of
Average Consumption Values. Tablet Detergent Indicator lights when the Tablet Detergent function is selected. Salt and
Rinse Agent indicators turn off when this function is activated.
Time Delay
Using the Delayed Start button, you may delay the starting time of your programme up to 9.5 hours with increments of
30 minutes. After delaying the start, press Start/Cancel button and close the door of your machine. Once the delay time is
over, the selected programme will start automatically.
Cancelling the delay function
Keep the Start/pause/cancel button pressed for 3 seconds. The selected delay period will be cancelled.
As soon as the cancelling starts, the water remaining in your machine will be drained for 30 seconds due to safety reasons.
You can use the submenu settings to change the “Warning Sound” and “Inner Illumination” settings you will use in your
machine.
To change the submenu settings:
Turn on your machine by pressing the On/Off button while pressing and holding Programme Selection and Start/Pause/
Cancel keys. Firstly, P1 indicator will light up on the display. Select the desired setting (P1, P2, P3, P4) by pressing the
Programme Selection key.
P1: Warning Sound (ON) - Inner illumination (ON)
P2: Warning Sound (OFF) - Inner illumination (ON)
P3: Warning Sound (OFF) - Inner illumination (OFF)
P4: Warning Sound (ON) - Inner illumination (OFF)
Save the selected setting by pressing Start/Pause/Cancel key again.
Warning Sound and Inner Illumination Settings (Depends on model)
Printed in Turkey Part no: 17 9829 01 00 Revision: CD-10/13
Beko plc, Beko House, Caxton Way, Watford, Hertfordshire, WD18 8UF
Tel : [phone] Fax : [phone] e-mail: [email protected] www.beko.co.uk
All manuals and user guides at all-guides.com