Beko BAW 389 EU User manual

Washing Machine
User Manual
BAW 389 EU
2820528048_EN/ 03-12-19.(16:57)
Document Number:

1 General safety instructions
• Do not force open the locked
loading door. Door can be
opened a few minutes after the
washing cycle ends. In case
of forcing the loading door to
open, the door and the lock
mechanism may get damaged.
• Use detergents, softeners and
supplements suitable for automatic
washing machines only.
•
Follow the instructions on the label of
textiles and the detergent package.
•The water supply pressure required
to run the product is between 1 to
10 bars (0.1 – 1 MPa).
• Do not use old or used water inlet
hoses on the new product. It may
cause stains on your laundry.
1.2 Hot surface safety
A
CAUTION!
• While washing the laundry
at high temperatures, the
loading door glass will get hot.
Considering this fact, during
washing operation keep the
children away from the loading
door of the product to prevent
them touching it.
This section includes security
instructions which may help prevent
the injuries and material damage risks.
All kinds of warranties shall be invalid if
these instructions are not observed.
1.1 Life and property safety
A
CAUTION!
• Never place the product on a
carpet-covered floor. Electrical
parts will get overheated since
air cannot circulate from under
the device. This will cause
problems with your product.
• Unplug the product if it is not in
use.
•
Always have the installation and
repairing procedures carried out
by the Authorised Service Agent.
The manufacturer shall not be
held liable for damages that may
arise from procedures carried
out by unauthorised persons.
• The water supply and draining
hoses must be securely fastened
and remain undamaged.
Otherwise, water leak may occur.
• While there is still water inside
the product, never open the
loading door or remove the filter.
Otherwise, risk of flooding and
injury from hot water will occur.
This product was manufactured using the latest technology in environmentally friendly conditions.

3 / EN Washing Machine / User’s Manual
1.3 Children’s safety
A
CAUTION!
• This product can be used by
the children who are at the
age of 8 and over and the
people whose physical, sensory
or mental skills are not fully
developed or who do not have
necessary required experience
and knowledge as long as they
are supervised or trained about
the safe use of the product and
its risks. Children should not
play with the device. Cleaning
and maintenance works should
not be performed by children
unless they are supervised by
someone. Children of less than
3 years should be kept away
unless continuously supervised.
A
CAUTION!
• Packaging materials may be
dangerous for the children.
Keep packaging materials in a
safe place away from reach of
the children.
• Electrical products are
dangerous for the children.
Keep the children away from
the product when it is in use.
Do not allow them to play
with the product. Use child
lock to prevent children from
intervening with the product.
A
CAUTION!
• Do not forget to close the
loading door when leaving the
room where the product is
located.
• Store all detergents and
additives in a safe place away
from the reach of the children
by closing the cover of the
detergent container or sealing
the detergent package.
1.4 Electrical safety
B
DANGER!
• If the product has a failure, it
should not be operated unless
it is repaired by the Authorised
Service Agent. Risk of electric
shock!
• This product is designed to
resume operating in the event
of powering on after a power
interruption. If you wish to
cancel the programme, see
“Cancelling the programme”
section.
B
DANGER!
• Plug the product into a
grounded outlet protected by
a 16 A fuse. Do not neglect to
have the grounding installation
made by a qualified electrician.
Our company shall not be
liable for any damages that will
arise when the product is used
without grounding in accordance
with the local regulations.

4 / EN Washing Machine / User’s Manual
B
DANGER!
• Do not wash the product by
spraying or pouring water onto
it! Risk of electric shock!
• Never touch the power cable
plug with wet hands! Do not
grab the power cord to unplug
the machine, always unplug it
by holding the socket with one
hand, and pulling the plug with
the other hand.
• Product should be unplugged
during installation, maintenance,
cleaning and repair procedures.
B
DANGER!
• If the power cable is damaged,
it must be replaced by the
manufacturer, after sales service
or a similarly qualified person
(preferably an electrician) or
someone designated by the
importer in order to avoid
possible risks.
2.Important instructions for
environment
2.1 Compliance with WEEE Directive
This product complies with EU
WEEE Directive (2012/19/EU).
This product bears a classification
symbol for waste electrical and
electronic equipment (WEEE).
3.Intended use
• This product has been designed for domestic
use. It is not for commercial purposes or it
should not be used out of its intended use.
• The product must only be used
for washing and rinsing of laundry
that are marked accordingly.
• The manufacturer waives any responsibility
arisen from incorrect usage or transportation.
• The service life of your product is 10 years.
During this period, original spare parts will be
available to operate the appliance properly.
• This appliance is intended to be used in
household and similar applications such as:
– staff kitchen areas in shops, offices and other
working environments;
– farm houses;
– by clients in hotels, motels and other
residential type environments;
– bed and breakfast type environments;
– areas for communal use in blocks of flats or
in launderettes.
This product has been manufactured with
high quality parts and materials which can
be reused and are suitable for recycling. Do
not dispose of the waste product with normal
domestic and other wastes at the end of its
service life. Take it to the collection center
for the recycling of electrical and electronic
equipment. Please consult your local
authorities to learn about these collection
centers.
Compliance with RoHS Directive:
The product you have purchased complies
with EU RoHS Directive (2011/65/EU). It
does not contain harmful and prohibited
materials specified in the Directive.
2.2 Package information
Packaging materials of the product are
manufactured from recyclable materials in
accordance with our National Environment
Regulations. Do not dispose of the
packaging materials together with the
domestic or other wastes. Take them to
the packaging material collection points
designated by the local authorities.

5 / EN Washing Machine / User’s Manual
4 Technical specifications
Supplier name or trademark Beko
Model name BAW389 EU
Rated capacity (kg) 9
Maximum spin speed (rpm) 1200
Built-in No
Height (cm) 84
Width (cm) 60
Depth (cm) 64
Net weight (±4 kg.) 72
Single Water inlet / Double Water inlet • / -
• Available
Electrical input (V/Hz) 220 V / 50Hz
Total current (A) 10
Total power (W) 2000
Main model code 928

6 / EN Washing Machine / User’s Manual
4.1 Installation
• Apply to the nearest authorised service
agent for the installation of your product.
• Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer's
responsibility.
• Make sure that the water inlet and discharge
hoses as well as the power cable are not
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.
• Make sure that the installation and electrical
connections of the product are performed
by authorised service. Manufacturer shall
not be held liable for damages that may
arise from procedures carried out by
unauthorised persons.
• Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products cause
risks for your safety.
4.1.1 Appropriate installation location
• Place the product on a hard and level floor.
Do not put it onto a carpet with high pile or
other similar surfaces.
• When the washing machine and dryer are
placed on top of each other, their total
weight –when loaded– amounts to 180 kg.
Place the product on a solid and flat floor
that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product in the
environments where the temperature falls
below 0 ºC.
• Leaving a gap at the sides of the machine is
suggested to reduce vibration and noise
• On a graduated floor, do not place the
product next to the edge or on a platform.
• Do not place heat sources such as Hobs,
Irons, Ovens, etc. on the washing machine
and do not use them on the product.
4.1.2 Removing packaging reinforcement
Tilt the machine
backwards to remove the
packaging reinforcement.
Remove the packaging
reinforcement by pulling
the ribbon. Do not make
this operation alone by
yourself.
4.1.3 Removing the
transportation locks
1. Loosen all bolts with an appropriate wrench
until they turn freely.
2. Remove the transport safety bolts by
turning them slightly.
3. Insert the plastic covers in the bag
containing the user manual to the openings
on the rear panel.
A
CAUTION!
• Remove the transportation safety bolts
before operating the washing machine!
Otherwise, the product will be damaged.
C
INFORMATION
• Keep the transportation safety
bolts in a safe place to reuse when
the washing machine needs to
be moved again in the future.
• Install the transport safety bolts in reverse
order of the disassembly procedure.
• Never move the product without
the transportation safety bolts
properly fixed in place!
4.1.4 Connecting water supply
C
INFORMATION
• It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in
one minute to have your machine run
smoothly. Attach a pressure reducing
valve if water pressure is higher.
A
CAUTION!
• Models with a single water inlet should
not be connected to the hot water
tap. In such a case the laundry will get
damaged or the product will switch to
protection mode and will not operate.

7 / EN Washing Machine / User’s Manual
1 Tighten the nuts of the hose by hand.
Never use a tool when tightening the nuts.
2 When hose connection is completed,
check whether there is leak problems at the
connection points by opening the taps fully. If
any leaks occur, turn off the tap remove the
nut. Retighten the nut carefully after checking
the seal. In order to prevent the water leaks
and resultant damages, keep the taps closed
when you do not use the product.
4.1.5 Connecting the drain
hose to the drain
• Attach the end of the drain hose directly to
waste water drain, lavatory or bathtub.
A
CAUTION!
• Your drain house will be flooded if the
hose comes out of its housing during
water discharge. Moreover, there is risk of
scalding due to high washing temperatures!
In order to prevent such situations and
make sure that the machine performs water
intake and discharge processes without
any problem, fix the drain hose securely.
40 cm
100 cm
• Connect the drain hose to a minimum height
of 40 cm and a maximum height of 100 cm.
• In case the drain hose is elevated after laying
it on the floor level or close to the ground
(less than 40 cm above the ground), water
discharge becomes more difficult and the
laundry may come out excessively wet.
Therefore, follow the heights described in
the figure.
• To prevent the waste water to go back
into the machine again and to ensure easy
drainage, do not immerse the end of the
hose into the waste water or do not insert
it into the drain for more than 15 cm. If it is
too long, cut it short.
• The end of the hose should not be bent,
it should not be stepped on and the hose
must not be pinched between the drain and
the machine.
• If the length of the hose is too short, use
it by adding an original extension hose.
Length of the hose may not be longer than
3.2 m. To avoid water leak failures, the
connection between the extension hose and
the drain hose of the product must be fitted
well with an appropriate clamp as not to
come off and leak.
4.1.6 Adjusting the feet
A
CAUTION!
• In order to ensure that the product
operates more silently and vibration-
free, it must stand level and balanced
on its feet. Balance the machine by
adjusting the feet. Otherwise, the product
may move from its place and cause
crushing and vibration problems.
• Do not use any tools to loosen the lock
nuts. Otherwise, they will get damaged.
1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a
stable and balanced way.
3. Tighten all lock nuts by hand again.

8 / EN Washing Machine / User’s Manual
4.1.7 Electrical connection
Connect the product to a grounded outlet
protected by a 16 A fuse. Our company shall
not be liable for any damages that will arise
when the product is used without grounding in
accordance with the local regulations.
• Connection must comply with national regulations.
• The wiring for the electrical outlet circuit
must be sufficient to meet the appliance
requirements. Use of a Groud Fault Circuit
Interrupter (GFCI) is recommended.
• Power cable plug must be within easy reach
after installation.
• If the current value of the fuse or breaker
in the house is less than 16 Amps, have a
qualified electrician install a 16 Amp fuse.
• The voltage specified in the "Technical
specifications" section must be equal to
your mains voltage.
• Do not make connections via extension
cables or multi-plugs.
A
CAUTION!
• Damaged power cables must be replaced
by the Authorised Service Agents.
4.1.8 Initial use
Before starting to
use the product
make sure that
the preparations
are made which
are in line with the
“Important Safety
and Environment Instructions” and the
instructions in the “Installation” section.
To prepare the product for washing laundry,
perform first operation in Drum Cleaning
programme. If this program is not available
in your machine, apply the method which is
described in the section 4.4.2.
C
INFORMATION
• Use an anti-limescale suitable
for the washing machines.
• Some water might have remained
in the product due to the quality
control processes in the production.
It is not harmful for the product.
4.2 Preparation
4.2.1 Sorting the laundry
* Sort laundry according to type of fabric,
color, and degree of soiling and allowable
water temperature.
* Always obey the instructions given on the
garment tags.
4.2.2 Preparing laundry for washing
• Laundry items with metal attachments such
as, underwired bras, belt buckles or metal
buttons will damage the machine. Remove
the metal pieces or wash the clothes by
putting them in a laundry bag or pillow case.
• Take out all substances in the pockets such as
coins, pens and paper clips, and turn pockets
inside out and brush. Such objects may
damage the product or cause noise problem.
• Put small size clothes such as infant's socks
and nylon stockings in a laundry bag or
pillow case.
• Place curtains in without compressing them.
Remove curtain attachment items.
• Fasten zippers, sew loose buttons and
mend rips and tears.
• Wash “machine washable” or “hand
washable” labeled products only with an
appropriate programme.
• Do not wash colours and whites together.
New, dark coloured cottons release a lot of
dye. Wash them separately.
•
Tough stains must be treated properly before
washing. If unsure, check with a dry cleaner.
• Only use the dyes / color changers and
descaling agents which are appropriate
to machine wash. Always follow the
instructions on the package.
• Wash trousers and delicate laundry turned
inside out.
• Keep laundry items made of Angora wool in
the freezer for a few hours before washing.
This will reduce pilling.
•
Laundry that are subjected to materials such
as flour, lime dust, milk powder, etc. intensely
must be shaken off before placing into the
machine. Such dusts and powders on the
laundry may build up on the inner parts of
the machine in time and can cause damage.

9 / EN Washing Machine / User’s Manual
4.2.3 Things to be done for energy saving
Following information will help you use the product
in an ecological and energy-efficient manner.
• Operate the product in the highest
capacity allowed by the programme you
have selected, but do not overload; see,
"Programme and consumption table". See,
“Programme and consumption table"
• Always follow the instructions on the
detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities
of lightly soiled laundry.
•
Do not use prewash and high temperatures
for laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer,
select the highest spin speed recommended
during washing process.
•
Do not use more detergent than the
recommended amount specified on its package.
4.2.4 Loading the laundry
1. Open the laundry cover.
2. Put the laundry items into the machine in a
loose manner.
3.
Push and close the loading cover until you
hear the locking sound. Ensure that no items
are caught in the door. The loading door is
locked while a programme is running. The
door can only be opened a while after the
programme comes to an end.
4.2.5 Correct load capacity
The maximum load capacity depends on the
type of laundry, the degree of soiling and the
washing programme desired.
Machine automatically adjusts the water amount
according to the weight of the laundry put inside it.
A
WARNING!
• Follow the information in the
“Programme and consumption table”.
When overloaded, machine’s washing
performance will drop. Moreover, noise
and vibration problems may occur.
4.2.6 Using detergent and softener
C
INFORMATION
• When using detergent, softener, starch, fabric
dye, bleacher and decolorant, descaling
agents; read the manufacturer’s instructions
written on the package and follow the dosages
specified. Use measuring cup if available.
1
3
2
The detergent drawer
is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– ( ) in addition, there
is a siphon piece in the
softener compartment.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting
the washing programme.
• While the washing cycle is in progress, do
not leave the detergent dispenser open!
• When using a programme without prewash,
do not put any detergent into the prewash
compartment (compartment nr. "1").
• In a programme with prewash, do not
put liquid detergent into the prewash
compartment (compartment nr. "1").
• Do not select a programme with prewash if
you are using a detergent bag or dispensing
ball. Place the detergent bag or the dispensing
ball directly among the laundry in the machine.
• If you are using liquid detergent, do
not forget to place the liquid detergent
container into the main wash compartment
(compartment number “2”).
Choosing the detergent type
Detergent type to be used depends on the
fabric type and color.
• Use different detergents for coloured and
white laundry.
• Wash your delicate clothes only with special
detergents (liquid detergent, wool shampoo,
etc.) used solely for delicate clothes.
• When washing dark coloured clothes and quilts,
it is recommended to use liquid detergent.
• Wash woolens with special detergent made
specifically for woolens.
A
CAUTION!
• Use only detergents manufactured
specifically for washing machines.
• Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used
depends on the amount of laundry, the degree
of soiling and water hardness.

10 / EN Washing Machine / User’s Manual
• Do not use amounts exceeding the dosage
quantities recommended on the detergent
package to avoid problems of excessive
foam, poor rinsing, financial savings and
finally, environmental protection.
• Use lesser detergent for small amounts or
lightly soiled clothes.
Using softeners
Pour the softener into the softener
compartment of the detergent drawer.
• Do not exceed the (>max<) level sign on the
softener compartment.
• If the softener has lost its fluidity, dilute it with
water before putting it in the detergent drawer.
Using liquid detergents
If the product contains a liquid detergent cup:
2
2
• Put the liquid detergent container into the
compartment no “2”.
• If the liquid detergent lost its fluidity, dilute it with
water before putting it into the detergent container.
If the product is equipped with a liquid
detergent part:
• When you want to use liquid detergent, pull
the apparatus towards yourself. The part
that falls down will serve as a barrier for the
liquid detergent.
• If required, clean the apparatus with water
when it is in place or by removing it.
• If you will use powder detergent, the
apparatus must be secured at top position.
If the product does not contain a liquid
detergent cup:
• Do not use liquid detergent for the prewash
in a programme with prewash.
• Liquid detergent stains your clothes when
used with Delayed Start function. If you are
going to use the Delayed Start function, do
not use liquid detergent.
Using gel and tablet detergent
•
If the gel detergent thickness is fluidal and
your machine does not contain a special liquid
detergent cup, put the gel detergent into the
main wash detergent compartment during
first water intake. If your machine contains a
liquid detergent cup, fill the detergent into this
cup before starting the programme.
• If the gel detergent thickness is not fluidal or
in the shape of capsule liquid tablet, put it
directly into the drum before washing.
• Put tablet detergents into the main wash
compartment (compartment nr. "2") or
directly into the drum before washing.
Using starch
• Put the liquid soda, powder soda or the
fabric dye into the softener compartment.
• Do not use softener and starch together in a
washing cycle.
• Wipe the inside of the machine with a damp
and clean cloth after using starch.
Using limescale remover
• When required, use limescale removers
manufactured specifically for washing
machines only.
Using bleaches
• Add the bleach at the beginning of the
washing cycle by selecting a prewash
program. Do not put detergent in the
prewash compartment. As an alternative
application, select a programme with extra
rinse and add the bleaching agent while the
machine is taking water from the
detergent
compartment during first rinsing step.
• Do not use bleaching agent and detergent
by mixing them. Use just a little amount
(approx. 50 ml) of bleaching agent and
rinse the clothes very well as it causes skin
irritation. Do not pour the bleach onto the
laundry and do not use it with the colored items.
• When using oxygen-based decolorant,
select a program which washes the laundry
at a low temperature.
• Oxygen-based decolorant can be used with
the detergent; however, if it is not at the
same consistence, first put detergent in the
compartment number “2” in the detergent
dispenser and wait for the machine to flush
the detergent when taking in water. While
the machine continues taking in water, add
decolorant in the same compartment.

11 / EN Washing Machine / User’s Manual
4.2.7 Tips for efficient washing
Clothes
Light Colours and
Whites Colours Black/Dark
Colours
Delicates/
Woolens/Silks
(Recommended temperature
range based on soiling level:
40-90 oC)
(Recommended temperature
range based on soiling level:
cold-40 oC)
(Recommended
temperature range
based on soiling
level: cold -40 oC)
(Recommended
temperature range
based on soiling
level: cold -30 oC)
Soiling Level
Heavily
Soiled
(difficult
stains such
as grass,
coffee, fruits
and blood.)
It may be necessary to pre-
treat the stains or perform
prewash. Powder and liquid
detergents recommended
for whites can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to clean
clay and soil stains and the
stains that are sensitive to
bleaches.
Powder and liquid
detergents recommended
for colors can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to clean
clay and soil stains and the
stains that are sensitive to
bleaches. Use detergents
without bleach.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended
for heavily soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woolen and silk
clothes must be
washed with special
woolen detergents.
Normally
Soiled
(For example,
stains caused
by body on
collars and
cuffs)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
normally soiled clothes.
Powder and liquid detergents
recommended for colors
can be used at dosages
recommended for normally
soiled clothes. Detergents
which do not contain bleach
should be used.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended for
normally soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woolen and silk
clothes must be
washed with special
woolen detergents.
Lightly
Soiled
(No visible
stains exist.)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
lightly soiled clothes.
Powder and liquid detergents
recommended for colors
can be used at dosages
recommended for lightly
soiled clothes. Detergents
which do not contain bleach
should be used.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended
for lightly soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woolen and silk
clothes must be
washed with special
woolen detergents.
4.2.8 Displayed Program Time
You can see the programme duration on the
display of your machine while selecting a
programme. Depending on the amount of laundry
you have loaded into your machine, foaming,
unbalanced load conditions, fluctuations in power
supply, water pressure and program settings, the
programme duration is automatically adjusted
while the programme is running.
SPECIAL CASE: At programme start of Cottons
and Cotton Eco programmes, display shows the
duration of half load, which is the most common
use case. After programme starts, in 20-25
minutes actual load is detected by the machine.
And if the detected load is higher than half load;
washing program will be adjusted accordingly and
program duration increased automatically. You
may follow this change on the display.

12 / EN Washing Machine / User’s Manual
4.3 Operating the product
4.3.1 Control panel
1 - Programme Selection Knob (Uppermost
position On / Off)
2 - Display
3 - End Time Adjustment Button
4 - Programme Follow-up Indicator
5 - Start/Pause Button
6 - Auxiliary Function Button 3
7 - Auxiliary Function Button 2
8 - Auxiliary Function Button 1
9 - Spin Speed Adjustment Button
10 - Temperature Adjustment Button
GentleCare
Synthetics
Cottons
Daily Express
XpressSuperShort
Mix 40
Spin+Drain
Spin
DoorLock
Wash
CottonsEco
Woollens
HandWash
Duvet
DownWear
Outdoor
Sports
DarkCare
Jeans
Hygiene+
AntiCrease+
End / Cancel
60°
1200
20°
90°
40°
30°
1000
800
600
Start/
Pause
Extra
Rinse
Prewash
Temp. Spin Fast+
GentleCare
Synthetics
Cottons
Daily Express
XpressSuperShort
Mix 40
Spin+Drain
Spin
DoorLock
Wash
CottonsEco
Woollens
HandWash
Duvet
DownWear
Outdoor
Sports
DarkCare
Jeans
Hygiene+
AntiCrease+
End / Cancel
60°
1200
20°
90°
40°
30°
1000
800
600
Start/
Pause
Extra
Rinse
Prewash
Temp. Spin Fast+
1 2 3 4
57 68910
4.3.2 Preparing the machine
1. Make sure that the hoses are connected
tightly.
2. Plug in your machine.
3. Turn the tap on completely.
4. Place the laundry in the machine.
5. Add detergent and fabric softener.
4.3.4 Programme and consumption table
4.3.3 Programme selection and
tips for efficient washing
1. Select the programme suitable for the type,
quantity and soiling degree of the laundry
in accordance with the "Programme and
consumption table" and the temperature
table below.
2. Use the Programme Selection knob to
select the desired programme.
EN 2Auxiliary functions
Programme
Max. Load (kg) Water Consumption (l) Energy Consumption (kWh) Max. Speed***
Prewash Fast+ Extra Rinse AntiCrease+
Selectable
temperature range
°C
Cottons
90 9 102 2,60 1200 • • • •Cold - 90
60 9 98 1,90 1200 • • • • Cold - 90
40 9 95 1,10 1200 • • • • Cold - 90
Cottons Eco
60** 9 56 1,120 1200 Cold - 60
60** 4,5 42 0,670 1200 Cold - 60
40** 4,5 42 0,670 1200 Cold - 60
Synthetics 60 4 75 1,40 1200 • • • • Cold - 60
40 4 73 0,95 1200 • • • • Cold - 60
Daily Express / Xpress Super Short
90 9 72 2,30 1200 • • • Cold - 90
60 9 72 1,30 1200 • • • Cold - 90
30 9 72 0,25 1200 • • • Cold - 90
Daily Express / Xpress Super Short+Fast+ 30 2 48 0,15 1200 • • • Cold - 90
Mix 40 40 4 75 1,00 800 • • •Cold - 40
Woollens / Hand Wash 40 2 55 0,55 1200 •Cold - 40
GentleCare 40 4 58 0,80 800 •Cold - 40
Outdoor / Sports 40 4 58 0,60 1200 •Cold - 40
Dark Care /Jeans 40 4 88 1,05 1200 • • * • Cold - 40
StainExpert 30 4,5 85 1,70 1200 • • 30 - 60
Duvet / Down Wear 60 - 105 1,90 1000 • 40-60
Shirts 60 4 70 1,90 800 • • • • 40-60
Hygiene+ 90 9 135 3,05 1200 * 40-90
Drum Cleaning+ 90 - 85 2,90 600 90

13 / EN Washing Machine / User’s Manual
• : Selectable
* : Automatically selected, cannot be cancelled.
** : Energy Label Programme
***: If the maximum spin speed of the machine
is lower, you can select values up to the
maximum spin speed value.
- : See the programme description for
maximum load.
C
INFORMATION
• Water and power consumption may
vary subject to the changes in water
pressure, water hardness and water
temperature, ambient temperature,
type and amount of laundry, selection
of auxiliary functions and spin speed,
and changes in the mains voltage.
• When selecting a programme, you can
see the washing duration on the display of
your machine. Depending on the amount
of laundry you have loaded into the
machine, there might be a difference of 1
to 1.5 hours between the duration shown
on the display and the actual duration of
the washing programme. The duration
will be corrected automatically right after
the washing programme has started.
• The auxiliary functions in the table may vary
according to the model of your machine.
• Auxiliary function selection modes can be
changed by the manufacturing company.
Existing selection modes can be removed
or new selection modes can be added.
4.3.5 Main programmes
Depending on the type of fabric, use the
following main programmes.
• Cottons
You can wash your durable cotton laundry
(sheets, bedlinen, towels, bathrobes, underwear
etc.) in this programme. When you press the
quick wash function key, programme duration
becomes notably shorter but effective washing is
ensured thanks to intense washing movements.
If the quick wash function is not selected,
superior washing and rinsing performance is
ensured for your heavily soiled laundry.
• Synthetics
You can use this programme to wash t-shirts,
syntetic/cotton mix fabrics etc. Programme
duration is notably shorter and efficient
washing performance is ensured. If the
quick wash function is not selected, superior
washing and rinsing performance is ensured
for your heavily soiled laundry.
• Woollens / Hand Wash
Use this programme to wash your woolen/
delicate clothes. Select the appropriate
temperature complying with the tag of your
clothes. Your laundry will be washed with very
delicate movements to avoid any damage.
“Woolen programme of this
machine has been approved
by The Woolmark Company
for washing machine-
washable products. These
products should be washed
in accordance with the instructions on the
label and of the manufacturer of the
machine.M13985”.
“Woolmark is a registered trademark in the
United Kingdom, Ireland, Hong Kong and India.”
4.3.6 Additional programmes
For special cases, additional programmes are
available in the machine.
C
INFORMATION
• Additional programmes may differ
according to the model of the machine.
• Cottons Eco
Use to wash your normally soiled, durable
cotton and linen laundry. Although it washes
longer than all other programmes, it provides
high energy and water savings. Actual
water temperature may be different from the
washing temperature stated. When washing
less amount of laundry (e.g. half the capacity
or less), duration of programme steps may
automatically become shorter. In this case,
energy and water consumption will decrease
more, providing a more economic wash.

14 / EN Washing Machine / User’s Manual
• Hygiene+
Applying a steam step at the beginning of the
programme allows to soften the dirt easily.
Use this programme for your laundry (baby
clothes, bed sheets, bedlinen, underwear, etc.
cotton items) for which you require an anti-
allergic and hygienic washing at high temperature
with intensive and long washing cycle. The high
level of hygiene is ensured thanks to the steam
application before the programme, long heating
duration and additional rinsing step.
• Programme was tested by “The British Allergy
Foundation” (Allergy UK) with the 60°C
temperature option selected and it was
certified in terms of its efficacy in eliminating
allergens in addition to bacteria and mould.
Allergy UK is the trademark of the
British Allergy Foundation. The Seal of
Approval has been designed to
provide guidance to persons who
want information whether the product
significantly decreases the amount of
allergens in the environment it is installed or whether it
limits/reduces/eliminates the allergens. Its purpose is to
provide evidence that the products have been tested
scientifically or reviewed to provide measurable results.
• GentleCare
You can use this programme to wash delicate
laundry such as cotton/synthetic mix knitted
clothes or socks. Washing movements in this
programme are more delicate. Set the temperature
to 20 degrees or use the Cold Wash option for
clothes whose colour you wish to preserve.
• Daily Express / Xpress Super Short
Use this programme to wash your lightly soiled
cotton clothes in a short time. The programme
duration can be reduced down to 14 minutes
when the quick wash function is selected. When
the quick wash function is selected, maximum 2
(two) kg of laundry must be washed.
• Dark Care / Jeans
Use this programme to preserve the colour
of your dark-coloured clothes and jeans. This
programme provides high efficiency in washing,
thanks to a special drum movement, even at low
temperatures. It is recommended to use liquid
detergent or woolen shampoo for dark coloured
laundry. Do not wash your delicate clothes that
contain wool etc. in this programme.
• Mix 40
You can use this programme to wash cottons and
synthetics together without the need to sort them.
• Shirts
This programme is used to wash the shirts
made from cotton, synthetic and synthetic
blended fabrics altogether. It reduces wrinkles.
Steam is applied at the end of the programme to
help the wrinkle reducing function. The special
spin profile and steam applied at the end of the
programme reduce the wrinkles on your shirts.
When the quick wash function is selected, the
Pre-treatment algorithm is executed.
• Apply the pre-treatment chemical on your
garments directly or add it together with
detergent when the machine starts to take water
from the main washing compartment. Thus, you
can obtain the same performance as you obtain
with normal washing in a much shorter period of
time. Usage life of your shirts increases.
• Outdoor / Sports
Use this programme to wash outdoor/sports
clothes that contain cotton/synthetic mix, as
well as waterproof cloths like gore-tex. This
programme washes your laundry delicately
thanks to its special turning movements.
• Duvet / Down Wear
Use this programme to wash your fiber duvets
that bear "machine washable" tag. Check that
you have loaded the duvet correctly in order not
to damage the machine and the duvet. Remove
the duvet cover before loading the duvet into the
machine. Fold the duvet into two and load it into
the machine. Load the duvet into the machine
paying attention to place it in a way that it will
not contact the bellow or the glass.
Steam is applied at the end of the programme
to soften bulky laundry such as towels.
C
INFORMATION
• Do not load the machine with more than
a double fibre duvet (200 x 200 cm).
• Do not wash your cotton duvets,
pillows etc. in the machine.
A
CAUTION!
• Do not use the washing machine to
wash materials other than carpets,
rugs etc. Otherwise, permanent
damage will occur to the machine.

15 / EN Washing Machine / User’s Manual
• StainExpert
Your washing machine has a special stain
programme ensuring that different types of
stains are removed in the most efficient way.
Use this programme only to use durable,
colourfast cottons. Do not wash delicate or
non-colourfast clothes in this programme.
You should check the tags of clothing before
washing (recommended for shirts, trousers,
shorts, t-shirts, baby clothes, pyjamas, aprons,
table cloths, bedding, duvet covers, sheets,
bath/brach towels, regular towels, socks, and
cotton underwear suitable for long washing
cycles at a high temperature). With the auto
stain programme, you can remove 24 types of
stains grouped into two categories according to
quick function selection. Here you can see the
stain groups based on quick function selection.
Below you will find the stain groups based on
the quick function.
When the quick function is selected:
Blood Fruit juice
Chocolate Ketchup
Pudding Red Wine
Egg Curry
Tea Jam
Coffee Coal
When the quick function is not selected:
Butter Food
Grass Mayonnaise
Mud Salad Dressing
Coke Make-up
Sweat Machine Oil
Collar Soil Baby food
• Select the stain programme.
• In the stain groups stated above, find the
type of stain you want to remove and select
the quick auxiliary function selection key to
select the relevant group.
• Carefully read the tag of the clothing and
make sure that the temperature and spin
speed selected are suitable.
4.3.7 Special programmes
For specific applications, select any of the
following programmes.
• Rinse
Use when you want to rinse or starch separately.
• Spin+Drain
Use this program to remove the water on the
clothe/in the machine.
Before selecting this programme, select the
desired spin speed and press Start/Pause
button. First, the machine will drain the water
inside of it. Then, it will spin the laundry at
the selected spin speed, and drain the water
coming off of the laundry.
If you only want to drain the water without
spinning the laundry, select the “Spin+Pump
programme, and use the Spin Speed
Adjustment button to select the No Spin
function. Press the Start/Pause button.
C
INFORMATION
• Use a lower spin speed for
delicate laundries.
4.3.8 Temperature selection
Whenever a new programme is selected, the
recommended temperature for the selected
programme appears on the temperature indicator.
To decrease the temperature, press the
Temperature Adjustment button. Temperature
will decrease gradually. When the cold level is
selected, temperature level lights will not be on.
C
INFORMATION
• If the programme has not reached
the heating step, you can change
the temperature without switching
the machine to Pause mode.
4.3.9 Spin speed selection
Whenever a new programme is selected, the
recommended spin speed of the selected
programme is displayed on the spin speed
indicator.
To decrease the spin speed, press the Spin
Speed Adjustment button. Spin speed
decreases gradually. Then, depending on the
model of the product, "Rinse Hold" and "No
Spin" options appear on the display. When
the “No Spin” function is selected, rinse level
indicator lights will not be on.

16 / EN Washing Machine / User’s Manual
Rinse hold
If you are not going to unload your clothes
immediately after the programme ends, you
can use rinse hold function to keep your
laundry in the final rinsing water in order to
prevent them from getting wrinkled when
there is no water in the machine. Press Start/
Pause button after this process if you want to
drain the water without spinning your laundry.
Programme will resume where it left off, drain
the water and then it will be complete.
If you want to spin the laundry held in water,
adjust the Spin Speed and press Start/Pause
button. Programme will resume. Water will
be drained, laundry will be spun and the
programme will end.
C
INFORMATION
• If the programme has not reached the spin
step, you can change the spin speed without
switching the machine to Pause mode.
4.3.10 Auxiliary function selection
Select the desired auxiliary functions before
starting the programme. You can also select
or cancel auxiliary functions suitable for the
running programme without pressing the Start/
Pause button while the machine is operating.
To do this, the machine must be in a step
before the auxiliary function you are going to
select or cancel. If the auxiliary function cannot
be selected or canceled, light of the relevant
function will flash 3 times to warn the user.
C
INFORMATION
• If a second auxiliary function conflicting
with the first one is selected before starting
the machine, the function selected first
will be canceled and the second auxiliary
function selection will remain active.
• An auxiliary function which is not compatible
with the programme cannot be selected.
(See "Programme and consumption table")
• Auxiliary Function buttons may vary
according to the model of the machine.
4.3.10.1 Auxiliary functions
• Prewash
A Prewash is only worthwhile for heavily soiled
laundry. Not using the Prewash will save
energy, water, detergent and time.
C
INFORMATION
• Prewash without detergent is
recommended for tulle and curtains.
• Fast+
When this function is selected, durations of
relevant programmes get shorter by 50%.
Thanks to the optimised washing steps,
high mechanic activity and optimum water
consumption, high washing performance is
achieved in spite of the reduced duration.
• Extra Rinse
This function enables the machine to carry
out another rinsing cycle in addition to the
one carried out after the main wash. Thus, the
risk for sensitive skins (babies, allergic skins,
etc.) to be effected by the minimal detergent
remnants on the laundry can be reduced.
4.3.10.2 Functions/Programmes
Selected by Pressing the Function
Buttons for 3 Seconds
• Drum Cleaning+
To select this programme, press and hold the
auxiliary function button 1 for 3 seconds.
Use it regularly (every 1-2 months) to clean
the drum and ensure the required hygiene is
provided. Run the programme while the machine
is totally empty. To obtain better results, put
powder lime-scale remover for washing machines
into the detergent compartment no. “2”. When
the programme is over, leave the loading door
ajar so that the inside of the machine gets dry.

17 / EN Washing Machine / User’s Manual
C
INFORMATION
• This is not a washing programme.
It is a maintenance programme.
• Do not run this programme when there are
any objects in the machine. If you try to do
so, the machine will automatically detect that
there is load inside and abort the programme.
• Child Lock
You can prevent children from tampering with
the machine by using the Child Lock feature.
Thus you can avoid any changes in a running
programme.
C
INFORMATION
• If the Programme Selection knob is turned
when the Child Lock is enabled, "Con"
appears on the display. While the Child Lock
is enabled, you cannot make any change in
the programmes, the selected temperature,
the speed or the auxiliary functions.
• Even if another programme is selected
with the Programme Selection knob while
the Child Lock is enabled, previously
selected programme will continue running.
To enable Child Lock:
Press and hold the Auxiliary Function button 2
for 3 seconds. While you’re holding the button
pressed for 3 seconds, C03, C02 and C01
will be displayed respectively.Then, “Con” will
be displayed to warn the user that child lock
is enabled.If you press any button or turn the
Programme Selection knob while the Child Lock
is enabled, the same warning will be displayed.
To disable Child Lock:
Press and hold the Auxiliary Function button 2
for 3 seconds while the programme is running.
While you’re holding the button pressed for 3
seconds, C03, C02 and C01 will be displayed
respectively. Then, “COF” will be displayed to
warn the user that child lock is disabled.
C
INFORMATION
• In addition to the method above, to
deactivate the Child Lock, switch the
Programme Selection knob to On/Off
position when no programme is running,
and select another programme.
• Child Lock will not be disabled after
a power failure or unplugging.
• AntiCrease+
If you press and hold the auxiliary function button
3 for 3 seconds, this function will be selected
and the programme follow-up light of the relevant
programme will turn on. When this function is
selected, the drum will rotate for up to eight hours
to ensure that the clothes do not crease at the end
of the programme. At any time during these eight
hours, you can cancel the programme and unload
the machine. Just press any button or turn the
programme selection knob to end the function. The
programme follow-up light will remain on even if you
end the function by pressing any button. If you end
the function by turning the programme selection
knob, the programme follow-up light will remain on
or go off depending on the selected programme.
If you do not cancel the function by pressing the
Auxiliary Function button 3 for 3 seconds, it will be
used in the next washing cycles as well.
4.3.11 - End Time Adjustment
The End Time Adjustment function allows you to
set the end time of the programme up to 19 hours.
You can increase this time by 1-hour intervals.
C
INFORMATION
• Please do not use liquid detergent if you
have selected the End Time Adjustment
function. Stains might remain on the clothes.
1. Open the loading door, place the laundry
and add detergent, etc.
2. Select the washing programme,
temperature, spin speed and, if required,
the auxiliary functions.
3. Press the End Time Adjustment button and
select the desired time.
4. Press the Start/Pause button. The delayed end
time you have set will be displayed. Countdown
will start for delayed end. On the display, “_” will
move up and down next to the delayed end time.
C
INFORMATION
• If the programme has not started,
you can add laundry into the machine
during the delayed end time.
5. At the end of the countdown, duration of
the selected programme will be displayed.
“_” will disappear and the selected
programme will start.

18 / EN Washing Machine / User’s Manual
Changing the delayed end time
If you want to change the time during countdown:
Turn the programme selection knob to cancel the
delayed end time function, and then set the desired
time again.
1. Press the End Time Adjustment button. When
pressed for the first time, the programme
duration will be rounded up to the closest
whole number time. Each following press will
increase the time by an hour.
2. If you want to decrease the delayed end
time, press the
End Time Adjustment button
consecutively until the desired time is displayed.
Cancelling the delayed end function
If you want to cancel the delayed end time
countdown and start the programme immediately:
1. Set the Programme Selection knob to any
programme. This way, the Delayed End time
will be cancelled. The End/Cancel light will
flash continuously.
2. Then, select the programme you want to run
again.
3. Press Start/Pause button to start the programme.
4.3.12 Starting the programme
1. Press Start/Pause button to start the programme.
2. Programme follow-up light showing the
startup of the programme will turn on.
C
INFORMATION
• If no programme is started or no key is
pressed within 10 minutes during the
programme selection process, the display
lights will go off. Once the Programme
Selection knob is turned or any button is
pressed, display lights will turn on again.
4.3.13 Progress of programme
Progress of a running programme can be
followed from the Programme Follow-up
indicator. At the beginning of each programme
step, the relevant indicator light will turn on.
C
INFORMATION
• If the “Anti-crease+” auxiliary function
has been selected, “End” LED and “Anti-
crease+” LED will be on at the same
time while this step is continuing.
• To end the programme while the “Anti-
crease+” step is running, simply press any
button or turn the programme selection knob.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make
must be something that will be carried out after
the programme step that is running. If the change
is not suitable, relevant lights will flash 3 times.
C
INFORMATION
• If the machine does not proceed to the spinning
step, the Rinse Hold function might be active or
the automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the machine.
4.3.14 Loading door lock
There is a locking system on the loading door of
the machine that prevents opening of the loading
door in cases when the water level is unsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. The machine
checks the level of the water inside. If the level is
suitable, the loading door light will turn off and the
loading door can be opened within 1-2 minutes.
If the level is unsuitable, the loading door light
will remain on and the loading door cannot be
opened. If you are obliged to open the loading
door while the Loading Door light is on, you
must cancel the current programme. See
"Cancelling the programme"
4.3.15 Changing the selections
after programme has started
Switching the machine to pause mode
Press the Start/Pause to switch the machine
to pause mode while a programme is running.
The light of the current programme will flash on
the Programme Follow-up indicator, indicating
that the machine has switched to pause mode.
Also, when the loading door is ready to be
opened, the Loading Door light will turn off in
addition to the programme step light.

19 / EN Washing Machine / User’s Manual
Changing the auxiliary function, speed and
temperature
Depending on the step the programme has
reached, you can cancel or select auxiliary
functions. See “Auxiliary function selection”.
You can also change the speed and
temperature settings. See "Spin speed
selection" and "Temperature selection".
C
INFORMATION
• If no change is allowed, the
relevant light will flash 3 times.
Adding and removing laundry
1. Press the “Start/Pause” button to pause the
machine. The programme follow-up light of
the relevant step during which the machine
was switched into the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the loading door and add or take out
laundry.
4. Close the loading door.
5. Make changes in auxiliary functions,
temperature and speed settings if necessary.
6. Press the “Start/Pause” button to start the
machine.
4.3.16 Cancelling the programme
To cancel the programme, turn the Programme
Selection knob to select another programme.
Previous programme will be cancelled. End/
Cancel light will flash continuously to notify that
the programme has been canceled.
When you turn the Programme Selection knob,
the machine will end the programme but will not
discharge the water inside. When you select
and start a new programme, the newly selected
programme will start depending on the step
the previous programme was canceled in. For
example, the machine may take in additional
water or continue to wash with the water inside.
C
INFORMATION
• Depending on the step where the
programme was canceled in, you may have
to add detergent and softener again for
the programme you have selected anew.
4.3.17 End of programme
At the end of the programme, “End” will be
displayed.
1. Wait until the light of the loading door goes
off completely.
2. Switch the programme selection knob to
On/Off to switch off the machine.
3. Take out your laundry and close the loading
door. Your machine is now ready for the
next washing cycle.
4.3.18 Your machine has the
"Pause Mode" function.
After using the On/Off button to switch on the
machine, if you do not start any programme in
the selection step or do not perform anything
else, or if you do not do anything in 10 minutes
after the selected programme has ended, the
machine will automatically switch to energy
saving mode. Also, if your product has a display
that shows programme time, this display will
completely turn off. If you turn the Programme
Selection knob or touch any button, the lights
and the display will switch back to the previous
position. The selections you make when exiting
the energy efficiency mode may change. Check
if your selections are correct before starting the
programme. If necessary, make adjustments
again.This is not an error.

20 / EN Washing Machine / User’s Manual
4.4 Maintenance and cleaning
Service life of product extends and frequently
experienced problems will be reduced if it is
cleaned at regular intervals.
4.4.1 Cleaning the detergent drawer
Clean the detergent
drawer at regular intervals
(every 4-5 washing cycles)
as shown below in order
to prevent accumulation of
powder detergent in time.
Lift the rear part of the siphon to remove it as
illustrated.
If more than normal amount of water and
softener mixture starts to gather in the softener
compartment, the siphon must be cleaned.
1 Press the dotted point on the siphon in the
softener compartment and pull towards you
until the compartment is removed from the
machine.
2. Wash the detergent drawer and the
siphon with plenty of lukewarm water in a
washbasin. In order to prevent the residues to
contact your skin, clean it with an appropriate
brush by wearing a pair of gloves.
3 Insert the drawer back into its place after
cleaning and make sure that it is seated well.
4.4.2 Cleaning the loading
door and the drum
For products with drum cleaning programme,
please see Operating the product -
Programmes.
C
INFORMATION
• Repeat Drum Cleaning process
in every 2 months.
• Use an detergent / anti-limescale
suitable for the washing machines.
After every washing
make sure that no foreign
substance is left in the
drum.
If the holes on the bellow shown in the figure is
blocked, open the holes using a toothpick.
C
INFORMATION
• Foreign metal substances will cause
rust stains in the drum. Clean the
stains on the drum surface by using
cleaning agents for stainless steel.
A
WARNING
• Never use steel wool or wire wool.
These will damage the painted,
chromated and plastic surfaces.
4.4.3 Cleaning the body
and control panel
Wipe the body of the machine with soapy
water or non-corrosive mild gel detergents as
necessary, and dry with a soft cloth.
Use only a soft and damp cloth to clean the
control panel.
4.4.4 Cleaning the water intake filters
There is a filter at the end of each water intake
valve at the rear of the machine and also at
the end of each water intake hose where they
are connected to the tap. These filters prevent
foreign substances and dirt in the water to
enter the washing machine. Filters should be
cleaned as they do get dirty.
1. Close the taps.
2. Remove the nuts of the water intake hoses
to access the filters on the water intake
valves. Clean them with an appropriate
brush. If the filters are too dirty, remove
them from their places with a pliers and
clean in this way.
3.
Take out the filters on the flat ends of the
water intake hoses together with the gaskets
and clean thoroughly under running water.
4. Replace the seals and filters carefully and
tighten their nuts by hand.