Bellhowell SOCKET FAN LIGHT User manual

BELL+HOWELL® SOCKET FANLIGHT™ ITEM NO. 8563ENCB
DISTRIBUTED BY EMSON® NY, NY, 10001 ©2022 EMSON® ALL RIGHTS RESERVED. MADE IN CHINA.
1-800-423-4248
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
SPECIFICATIONS:
• 120V, 420mA, 29W
• 1000 Lumens
THE LEDs ARE NON REPLACEABLE.
FOR INDOOR USE ONLY
• NEVER PLACE ANYTHING OVER THE FAN OR INTO THE UNIT BLADES WHEN IT’S RUNNING.
• USE IN OPEN LUMINAIRE ONLY.
• DO NOT USE WITH DIMMERS.
• DO NOT PLACE OBJECTS NEAR THE UNIT.
• ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE STANDING
PORTABLE LUMINAIRE.
• THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.
• DO NOT OPERATE ANY APPLIANCE AFTER IT MALFUNCTIONS, OR IS DROPPED, OR DAMAGED
IN ANY MANNER. RETURN APPLIANCE TO THE NEAREST AUTHORIZED SERVICE FACILITY FOR
EXAMINATION, REPAIR OR ELECTRICAL OR MECHANICAL ADJUSTMENT.
• UNIT SHOULD BE TURNED OFF WHEN NOT IN USE OR DURING CLEANING. FAN HAS TO COME
TO A COMPLETE STOP BEFORE HANDLING IT.
• 40 High Intensity LED Bulbs
• Suitable for E26 Light socket base
IMPORTANT SAFEGUARDS continued:
1000
LUMENS
3 FAN SPEEDS
3 LIGHT SETTINGS
REMOTE
CONTROL
& BRACKET
INSTRUCTIONS
NO WIRES
OR BATTERIES
REQUIRED
LED
TECHNOLOGY
E26
MEDIUM BASE SOCKET EXTENDER
INCLUDED
15.7" DIAMETER
SOCKET FAN LIGHT
2-IN-1 LED LIGHT & FAN
Great for all rooms around the house, including: bedrooms,
basements, attics, boiler rooms, garages & more

While holding the unit as shown above
(holding part A and part B at the same
time), twist the Socket Fanlight clockwise
to install it. Do not overtighten, but make
sure the fan is fully secured.
INSTALLATION No tools required.
ASSEMBLY USING THE REMOTE
MOUNTING OF REMOTE HOLDER
EQUIPPED WITH SAFETY OFF FEATURE
If the blades come in contact with an object during operation, the fan will stop.
To restart:
Option A: Turn the power OFF using the light switch for that socket, then switch
it back on. Now you can use the remote.
Option B: Just wait 1 minute before using the remote control again.
Remove the protective cap.
If needed, use the socket extender.
Screw it in clockwise. Do not overtighten,
but make sure the fan is fully secured.
Then, follow step 2 to install the Socket
Fanlight unit.
IMPORTANT SAFEGUARDS:
• KEEP FAN OUT OF REACH OF CHILDREN.
• WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE BRACKETS
WHEN INSTALLING THE BRACKETS, BALANCING THE BLADES, OR CLEANING THE UNIT.
DO NOT INSERT FOREIGN OBJECTS IN BETWEEN ROTATING FAN BLADES.
• CAUTION: TO REDUCE THE RISK OF INJURY TO PERSONS, INSTALL UNIT AT LEAST 3.05 M
(10 FEET) ABOVE THE FLOOR.
• CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
• THIS DEVICE CAN ONLY BE INSTALLED ON STATIONARY LIGHT SOCKET, CANNOT INSTALL
ON ANY NON STATIONARY OR LOOSE SETTING LIGHT SOCKET.
• TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS UNIT MUST BE INSTALLED WITH AN ISOLATING
WALL CONTROL/SWITCH.
• DUE TO SOCKET FANLIGHT HIGH INTENSITY LED BULBS, DO NOT STARE DIRECTLY INTO THE LED LIGHT.
• RISK OF ELECTRIC SHOCK - USE IN DRY LOCATION ONLY.
• SWITCH OFF THE POWER BEFORE INSTALLING THE UNIT.
1 2
Turn the Socket Fanlight ON using the
light switch for that socket. The light
will turn on High setting, fan will be off.
To turn on the fan or change the light
settings use the included remote.
Refer to “USING THE REMOTE”
section on next page.
Use the light switch to turn the
unit OFF (fan and light).
Turns unit OFF (fan and light).
Turns fan on at low setting. Keep pressing button to cycle through
other settings (Low/Medium/High/OFF).
Default light setting is High. Keep pressing button to cycle
through other settings (Low/Medium/High/OFF).
NOTE: Each time a button is pressed on a remote, a short beep will sound.
34
NOTE: Fan blades come packed
separately from the main power
unit. Assembly is required.
Insert each blade into the tab until
it clicks in, as shown on right.
The blades can only be inserted
one way.
• Peel off backing and place it
with the adhesive side down
on the back of the holder.
Press down for a few seconds.
• Peel off the other side and place
on the desired smooth surface.
Press the holder firmly onto the
surface for a few seconds.
Insert each screw into the openings
of the remote holder. Tighten to secure.
Using screws/anchors (included):
Using 3M tape (included):
INSERT
SCREW
INSERT
SCREW
Slide the
remote into
the holder.
PEEL OFF
TO REVEAL
ADHESIVE
SIDE
Turn the power OFF using the light switch for that socket before installing the unit.
Remote working distance: up to 16 feet (5m)
HOLD
A+B
A
B