Belson Outdoors DF6S-P User manual

Model # DF6S-P Instructions Sheet
www.belson.com
RECYCLED PLASTIC HEXAGONAL
PLAZA PICNIC TABLE
627 Amersale Drive
Naperville, IL 60563
Phone: [phone]
Fax: [phone]
[email protected]

J - TABLE TOP
( 1 ) - ONE TABLE TOP
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK
N - LEFT SEAT
( 3 ) - THREE LEFT SEATS
O - RIGHT SEAT
( 3 ) - THREE RIGHT SEATS
H - TABLE LEG
( 3 ) - THREE TABLE LEGS
R - TABLE CENTER
( 2 ) - TWO TABLE CENTERS
Q - SEAT SUPPORT
( 3 ) - THREE SEAT SUPPORTS
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.

www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.
6 - 3/8” X 4-1/4” HEX HEAD BOLT
12 - 3/8” FLAT WASHER
6 - 3/8” NYLON LOCK NUT
6 - #12 X 3” FLAT HEAD PHILLIPS SCREW
48 - #12 X 1-1/2” PAN HEAD PHILLIPS SCREW
ALSO NEED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
1 - #3 PHILLIPS DRIVE BIT
2 - 9/16” SOCKET WRENCH

www.belson.com
STEP #1:
SLIDE ( 1 ) ONE TABLE CENTER ON TO EACH END OF THE TABKE LEG AS SHOWN ABOVE. USE ( 1 ) ONE
3/8” X 4 1/4” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER
AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOE TO SECURE.
DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
3/8” X 4 1/4” HEX
HEAD BOLT
3/8” FLAT WASHER
3/8” FLAT WASHER
3/8” NYLON LOCK NUT

3/8” FLAT WASHER
3/8” NYLON LOCK NUT
www.belson.com
STEP #2:
SLIDE THE REMAINING TABLE LEGS INTO THE TABLE CENTERS. USE ( 1 ) ONE 3/8” X 4 1/4” HEX HEAD
BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8”
NYLON LOCK NUT PER HOLE TO SECURE.
DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
3/8” x 4 1/4” HEX
HEAD BOLT
3/8” FLAT
WASHER

www.belson.com
STEP #3:
WHILE THE TABLE TOP IS UPSIDE DOWN, PLACE THE LEG ASSEMBLY ONTO THE TABLE TOP AS SHOWN
ABOVE. ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEGS WITH THE PILOT HOLES IN THE TABLE TOP.
USE ( 1 ) ONE #12 X 2 1/2” PAN HEAD SCREW PER HOLE TO SECURE.
BE SURE TO TIGHTEN ALL SCREWS AFTER COMPLETING THIS STEP.
#12 x 2 1/2” PAN HEAD
PHILLIPS SCREW

www.belson.com
STEP #4:
WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEG TO THE
PILOT HOLES IN THE SEAT SUPPORT AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 3” FLAT HEAD SCREW
PER HOLE TO SECURE.
DO NOT TIGHTEN SCREWS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
#12 x 3” FLAT HEAD
PHILLIPS SCREW

www.belson.com
STEP #5:
WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE SEAT TO THE PILOT
HOLES IN THE SEAT SUPPORT AND THE TABLE LEG AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 1 1/2”
PAN HEAD SCREW PER HOLE TO SECURE.
BE SURE TO TIGHTEN ALL LOOSE SCREWS AFTER COMPLETING THIS STEP.
#12 X 1 1/2” PAN HEAD
PHILLIPS SCREW

www.belson.com
STEP #6:
WITH ASSISTANCE TURN THE TABLE OVER ONTO ITS LEGS, PLEASE USE CAUTION FOR THE
TABLE WEIGHS APPROXIMATELY 240 POUNDS.