Belson PB6HEX-ADA User manual

Model # PB6HEX-ADA Instructions Sheet
www.belson.com
HEXAGONAL PICNIC TABLE ADA
PARTS LIST:
26 - 3 1/2” ZINC PLATED LAG SCREWS
12 - 2 1/2” DECK SCREWS
6 - 2 1/2” LAG SCREWS
1 - #2 PHILLIPS HEAD DRIVER BIT
TOOLS NEEDED FOR INSTALLATION:
VARIABLE SPEED DRILL OR SCREW GUN
7/16 SOCKET OR IMPACT WRENCH
HAMMER OR RUBBER MALLET
INSTALLATION INSTRUCTIONS:
1. CHECK PARTS LIST AND VERIFY ALL PARTS AND HARD-
WARE.
2. ATTACH SEAT/LEG ANCHOR BLOCK TO BOTTOM OF SEAT
SUPPORT USING 3 1/2” LAG SCREWS WITH WASHERS. NEXT
USING 3 1/2” LAG SCREWS WITH WASHERS ATTACH SEAT TO
CENTER SUPPORT MAKING SURE YOU ANCHOR INTO
PRE-DRILLED DIVETS.
3. ON A FLAT SURFACE AND USING 12 1/2” DECK SCREWS
START THE SEAT ASSEMBLY. IT IS IMPORTANT THAT THE
SEATS BE ASSEMBLED IN THE ORDER DETAILED BELOW.
ALIGN THE SEATS AS SHOWN IN DIAGRAM. AFTER ALIGN-
MENT, SCREW
( 2 ) 2 1/2” DECK SCREWS INTO EACH POSITION LABELED A
ON THE DIAGRAM. PUT ALL SCREWS INTO POSITIONS A.
THEN SCREW ( 2 ) 2 1/2” DECK SCREWS INTO EACH POSI-
TION LABELED B ON THE DIAGRAM. DO NOT SCREW INTO
POSITION B FIRST. IF POSITION B IS SCREWED INI FIRST, A
HEX TABLE HARDWARE SEAT AND ANCHOR BOARDS
HEX TABLE LEGS HEX TABLE TOP ASSEMBLY
627 Amersale Drive
Naperville, IL 60563
Phone: [phone]
Fax: [phone]
[email protected]

www.belson.com
GAP WILL FORM BETWEEN ADJACENT SEATS AT POSITION A.
THIS GAP WILL CAUSE DIFFICULTY WITH FURTHER TABLE
ASSEMBLY, AND THIS GAP CAN’T BE COMPLETELY REMOVED
BY NEXT SCREWING INTO POSITION A.
4. POSITION THE SEAT ASSEMBLY APPROXIMATELY 15” OFF
THE FLOOR. A FIVE GALLON BUCKET UNDER THE CENTER
OF THE SEAT ASSEMBLY WORKS QUITE WELL.
5. REVIEW THE LEG POSITIONING DIAGRAM. INSERT ALL
THREE LEGS THROUGH THEIR RESPECTIVE SEAT. CENTER
EACH LEG TO THE COUNTER BORED HOLES IN THE SEAT
ASSEMBLY.
6. REMOVE THE BUCKET FROM UNDER THE SEAT ASSEMBLY.
PLACE THE TABLETOP ONTO THE LEGS.
7. CHECK ALIGNMENT OF TOP AND SEAT ASSEMBLY BEFORE
ATTACHING LAG SCREWS. FIRST ALIGN THE TABLETOP SO
THAT EACH LEG STICKS OUT SLIGHTLY PAST THE TABLETOP
UNDERSTRUCTURE. ADJUST UNTIL ALL THREE LEGS STICK
OUT THE SAME DISTANCE. THEN VERIFY THAT EACH LEG IS
FLAT AGAINST THE GROUND. NEXT CENTER THE TWO
VERTICAL SEAT SUPPORTS OF EACH LEG TO THE COUNTER
BORED HOLES IN THE SMALL BLOCKS UNDER EACH SEAT.
LASTLY VERIFY THE LEG ALIGNMENT. YOU MAY HAVE TO
ADJUST SEVERAL TIMES.
8. USING A 3 1/2” LAG SCREW, COMPLETELY SCREW
THROUGH THE COUNTER BORED PILOT HOLES. DO NOT
LEAN ON TABLETOP OR SEATS WHEN ASSEMBLING.
TOP = 3 HOLES WITH 3 1/2” LAG SCREWS
LEG = 3 HOLES WITH 3 1/2” LAG SCREWS
SEAT = 6 HOLES 2 1/2” LAG SCREWS