Nags Head Hammocks NHDWSC User manual

SINGLE ROPE CHAIR/ROCKER
INSTRUCTIONS
• Rubber Mallet
• Adjustable Wrench
• Phillips Head Screwdriver
(6) Barrel Nuts
(8) Locknuts
(4) Locknuts
(1) Allen Wrench
(16) Washers
(8) Washers
(8) 3.5” Hex Bolts
(4) 3.5” Hex Bolts
(4) 4.5” Barrel Bolts
(2) 4” Barrel Bolts
HARDWARE PACK
ROCKER HARDWARE PACK
SUGGESTED TOOLS
NOTE. Instructions not to scale.
ASSEMBLY
STEP 1. Start by setting rollup with left side facing up. Align left arm
with 3 holes as shown. Attach left arm using 3.5” Hex Bolt, with 1 washer
per side, secure with lock washer and repeat for right side.
NOTE. do not tighten bolts until Step 3, (4 for rocker).
3.5” Hex Bolt
Lock Nut

If you have purchased the Single Rope Rocker, continue with the
following steps.
ASSEMBLY
STEP 2. Set upright, move rollup forward. Starting with left upright,
secure in hole as shown with a 3.5” Hex Bolt with a washer on each side
of the material and secure with a lock nut. Rotate upright to align with
arm hole and secure using a 4” Barrel Bolt. Repeat for the right side.
STEP 3. Insert (4) 4.5” Barrel Bolts, 2 per side in top hole of
rollup. Align with top holes in upright. Secure rollup using
Barrel Bolts and Barrel Nuts. Tighten all bolts, insert cup holder
and enjoy!
Note : Rocker continues to step 4
STEP 4. Turn rocker on side with left side facing up. Align runner, small
end facing forward with holes at base of rocker legs. Secure using (2) 3.5”
Hex Bolts, 1 washer per side of runner and lock nut in front - one per hole.
Repeat for right side, only turning rocker so that the right side is up as
you complete the step. Tighten all bolts, insert cup holder, turn the rocker
upright and enjoy!
Barrel Nut
Lock Nut
Barrel Nut Lock Nut
3.5” Hex Bolt
4” Barrel Bolt
4.5” Barrel Bolt
3.5” Hex Bolt
#5075
Congratulations on purchasing this Original Nag’s Head Single Rope Chair/Rocker. QUESTIONS REGARDING THIS
PRODUCT? Call our customer service team, 252-295-0405.
INSTALLATION - Get somebody to help you, some pieces are heavy and a second pair of hands is always helpful.
Do not tighten bolts until the product is fully assembled. Some pieces are harder to fit in place and this will help. A
hammer or rubber mallet is needed during assembly. Do not over-tighten the bolts or screws. Build your item close
to where it will be used to eliminate diculty in moving once completed. For a uniform look, face all nuts in the same
direction.
MAINTENANCE - Great care has been put into manufacturing this item. However, it is made of high density resin and
some natural esthetic imperfections and dark spots are normal and should be expected. You can wash the wood and
the rope using a hose and some bleach water. You can also brush the wood to help remove dirt.
WARRANTY & RETURNS - Nags Head Hammocks products are guaranteed to be free of defects in both
workmanship and material. Prolonged exposure to weather conditions including snow, rain, and humidity are not
covered under the warranty, nor is damaged caused by normal wear, mildew, or improper care, including storage,
maintenance, and assembly. If you are not satisfied with an item, return it unused in its original packaging for a
complete refund or exchange. You can return it to any of our stores or to our warehouse, Nags Head hammocks, 305
Industrial Blvd., Greenville, NC 27834. Please include a copy of your receipt and your contact information.