Bergen 2327HN User manual

ASSEMBLY INSTRUCTIONS
2327HN
2327HN
1
BERGEN TALL SIDEBOARD/WINE RACK
OAK EFFECT/WHITE/GREY
IMPORTANT
FOR DOMESTIC USE ONLY
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
SEC/AY/12/19/HN1
After unpacking this product please keep the original packaging in case it needs to be returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• Never drag or push products as this could cause damage to the joints making it inferior.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Do not place this product next to a radiator or in direct sunlight.
• Do not drag or push items across your high gloss furniture as this may cause the surface to scratch.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack if subjected to heat.
Therefore it is recommended that room temperature is maintained, with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking will occur.
• For general cleaning use a soft cotton or micro fibre cloth, and do not use detergents of any kind.
• From time to time it may be necessary to tighten fittings, regular inspections should be carried out.
• Do not place on a wet or damp floor as staining may occur to your floor.

Please Note:
The below parts have all been stamped with the
part number to help identify them during assembly.
PARTS LIST
01
02
03
04
05 05
07
08
09
10
11
15
15
15
12
16 17
18
19
19
20
21
13
14
06
06 06
06
Part Number Part Code Part Description Quantity Carton
01 S400-405-033-HN1-01 Base Panel x1 2/2
02 S400-405-033-HN1-02 Left Side Panel x1 1/2
03 S400-405-033-HN1-03 Drawer Top Panel x1 1/2
04 S400-405-033-HN1-04 Fixed Shelf Panel x1 2/2
05 S400-405-033-HN1-05 Partition Panel x2 1/2
06 S400-405-033-HN1-06 Shelf Panel x4 1/2
07 S400-405-033-HN1-07 Division Panel x1 1/2
08 S400-405-033-HN1-08 Large Shelf Panel x1 1/2
09 S400-405-033-HN1-09 Superior Shelf Panel x1 1/2
10 S400-405-033-HN1-10 Right Side Panel x1 1/2
11 S400-405-033-HN1-11 Top Panel x1 2/2
12 S400-405-033-HN1-12 Upper Back Panel x1 2/2
13 S400-405-033-HN1-13 Lower Back Panel x1 2/2
14 S400-405-033-HN1-14 Large Back Panel x1 2/2
15 S400-405-033-HN1-15 Adjustable Shelf x3 1/2
16 S400-405-033-HN1-16 Large Door x1 2/2
17 S400-405-033-HN1-17 Small Door x1 2/2
18 S400-405-033-HN1-18 Drawer Front x1 2/2
19 S400-405-033-HN1-19 Drawer Side x2 1/2
20 S400-405-033-HN1-20 Drawer Bottom x1 1/2
21 S400-405-033-HN1-21 Drawer Back Panel x1 1/2
*Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe!!!
*Please assemble on a clean soft suface to avoid damage.
*Please check contents and read the instructions before commencing assembly.
*Assemble this product following the enclosed instructions carefully.
*Please take care to avoid damaging panels during assembly.
2
ITM/S307-
SEC/AY/12/19/HN1

70x
F
Nail 1/8x23mm
Flat Head Screw
O3,5x10mm
Flat Head Screw
O3,5x40mm
Dowel O8x25mm
Flan Head Screw
O3,5x14mm
Flan Head Screw
O3,0x20mm
Cam Nut O15mm
Back Panel Bracket
3
ITM/S307-
FITTINGS LIST
TIPS FOR FITTINGS CAM-LOCKS
USE
DO NOT USE
When fitting cam nut. Ensure starting
position is correct before you insert
connecting cam bolt turn clockwise until
secure.
CAMBOLT
Tighten until shoulder in
flush with panel. Do not
overtighten or undertighten
(see example beside).
Shoulder
Panel Panel
Cam bolt head needs to be in centre
CORRECT WRONG
!




18x
B
01x48x
RS
Glue Hole Plugs
14x
G09x
09x
H
I
Cam Bolt
04x
T
Washer
12x02x
Shelf Support Glass Holder
KL
34x
C10x
D
58x
E
01x
O
Drawer Runners
05x
05xN
M
Hinge
12 mm Hinge Plate
04x
01x
P
Q
Metal Leg
Adjustable Leg
10x
J
Union screw 18mm
02x
A
02x
U
Strap
SEC/AY/12/19/HN1

Pre-Assembly
Detail 2 Detail 17 Detail 18 Detail 19
Detail 1
1
2
3
Detail 1
Detail 1
Detail 1
Detail 1
Detail 2
Detail 2
Detail 2
Detail 2
Detail 18
Detail 18
Detail 17
Detail 18
Perform the adjustment
of the leg (Q) at the
moment of fixing it.
Detail 19
Detail 18
Detail 1
01
J
J
J
JJ
PPC
C
C
C
Q
Q
10x
C04x01x PQ
Metal Leg Adjustable Leg
10x
J
Union screw 18mm
Male
(Female)
Female
(Male)
(Male)
Flan Head Screw
O3,5x14mm
4
ITM/S307-
SEC/AY/12/19/HN1

Pre-Assembly
Detail 9
Detail 9
Detail 4
Detail 6
Detail 6
Detail 6
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3 Detail 6 Detail 9
O
Drawer Runners
1x
E
R
M
CC
K
Detail 4
O
D
D
Flat Head Screw
O3,5x10mm Dowel O8x25mm
PRE-DRILLED HOLE
PRE-DRILLED HOLE
Flan Head Screw
O3,5x14mm
SECOND HOLE
FIRST HOLE (LINE UP WITH PRE-DRILLED HOLE) LAST THIRD HOLE
O
5
ITM/S307-
02
03
04
R
Glue
02x
Shelf Support
K
06x
C11x
E03x
M
12 mm Hinge Plate
03x
D
SEC/AY/12/19/HN1