PRODUCT SPECIFICATIONS
BUTTON FUNCTION DESCRIPTION
•Hold the button down for 3 seconds to power on,
and hold again for 3 seconds to power off.
• When playing music, press this button to pause
music, and press again to continue playing music.
•When a call is incoming, press the button to answer
the phone, and push again to hang up the call. •Hold down the light button for 5 seconds to
remove Bluetooth pairing.
Multifunction Button:
“Volume - and Previous” Button:
Press the button to play the previous track, and hold
the button down to reduce the volume.
BLUETOOTH PAIRING SETTINGS
Hold down the multifunction button for 3 seconds to
power on. Wait until the blue light flashes, then open
the bluetooth mode on your smartphone and select
“CT602” to pair the device. It’s now paired. You can
broadcast your music! If not, start again or relaunch
the CT602.
CHARGING
Connect the included USB cord to the USB port
and plug it into a 5V USB outlet and the DC jack to
the CT602. During charging, the LED indicator light
will remain red. When the battery is full, the LED
indicator will turn green.
NOTE:
DC 5V
Bluetooth version
Battery capacity
Working hours
Frequency
Protocol
Communication
distance
V5.1, compatible V4.2 and V2.1+ED
2500mAH lithium battery 3.7
2402MHz-2480MHz
MAX: 6 hrs
10-15 meters (32.8-49.2 ft.)
A2DP/AVRCP/HFP/SPP/GAT
Speaker Mono mixing output 4Ω6W, high-
fidelity waterproof speaker (Φ57mm)
Dimensions4.94’’ x 4.94’’ x 6.63’’
LED light Yellow, Green, Red, Blue
LED mode 8 modes
Waterproof IP67
OWNER’S MANUAL
TM
Flowclear
58700E Floating LED Bluetooth Speaker
A
x1
B
x1
“Volume + and Next” Button:
Press the button to play the next track, and hold
the button down to increase the volume.
• Use the included cable and respect the voltage!
• Please charge before use.
•Before inserting the charger, dry the charging port.
6.63”
4.94 ”
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
IMPORTANT SAFETY INSTRUCTIONS
WARINING:
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
The light source/battery of this luminaire is not replaceable; when the light source/battery reaches its end of life the whole
luminaire shall be replaced.
The power source should meet limited power source or PS2 requirements according to IEC 62368-1/UL62368-1. Check
with your local authority or retailer for recycling advice.Battery disposal should be in compliance with any local regulations
that address the disposal of hazardous materials.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Max.ambient
50℃
Max RF output power: <10dBm
