BIANCO PUMPZ BIA-B10A Manual

Submersible Pump
BIA-B10A
BIA-B15A
BIA-B25A
BIA-B40A
BIA-B42A
BIA-B15VA
BIA-B25VA
BIA-B40VA
BIA-B75A
BIA-B75VA
BIA-B75KA
BIA-B120G

Installation & Operating Instructions
BIANCO B range of submersible pumps is suitable for small to medium dewatering and or
wastewater applications. The Vortex pumps (VA) are able to pump soft solids in suspension. The
KA cutter pump has a impeller with an edged tungsten tip and a grinding plate to assist with
cutting of fibrous materials.
The G grinder pump consists of a high chrome impeller and grinder which can grind soft solid
materials in sewage.
Dewatering Pumps: B10A, B15A, B25A, B40A, B42A, B75A
Vortex Pumps: B15VA, B25VA, B40VA, B75VA
Cutter Pump: B75KA
Grinder: B120G
Voltage: 240V 50Hz Single Phase
Submersible pumps are very quiet and are ideal for applications within residential areas for storm
water pits, basements, etc
Suitable Fluids
The Cutter (K) models are suitable for pumping soft solids in suspension. The Cutter and Grinder
(G) pumps are also suited to pump soft string-like materials such as hair, lint, straw etc. Grinder
models can pump cloth, rubber gloves, etc. The cutter and grinder pumps should not pump hard
solids as these will damage the pump face.
Pumps are not to be used for pumping flammable or corrosive fluids.
Installation
The BIANCO B series pumps are completely submersible up to 10 metres and can be installed
on a level surface in a stationary position connected to either fixed pipe work or flexible hose.
Never remove or lift a pump by the power cable. Instead connect a rope to the handle during
installation.
External float switch versions should be placed in a sump of a suitable size so that the float
switch is not restricted or could be caught in the up position. The float switch must be installed so
that the ON and OFF operating points can be easily reached, and that the float switch head is not
too close to the latching holder which prevents correct operation. The float switch must not touch
the base of the sump or tank which will prevent the pump turning off.
All pumps must not be allowed to run dry.
Motor Cooling
All models rely upon water flow around the motor for correct motor cooling.
All models are suitable to operate partially submerged for periods up to 10 minutes.
Operating at very low flows caused by high heads or restricted pipe work may cause motor over
heating.

Power Connection
A power point (10 amp) should be provided by a qualified electrician, and a residual current
device with a nominal trip current should be installed in compliance with the requirements of AS
3000.
All single phase models have an automatic reset thermal overload protection built in, and
overload will switch the motor off and later will automatically reset and switch the motor on when
the motor has cooled down.
The appliance (pump) is not intended for use by young children or infirm persons without
supervision
Young children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, the pump should be returned to White International or one of its
Service Agents for repair in order to avoid a hazard.
Trouble Shooting
Fault
Cause
Remedy
Pump does not start
No mains supply
Check that power is available and switch is on
Blown fuse or tripped breaker
Replace or reset
Impeller jammed
Disconnect power and clean impeller area
Pump has turned off on thermal cut out
Allow time to reset
Float switch jammed down
Free switch and move pump
Insufficient water level
Float switch must be 45 deg above horizontal
No or low flow
Strainer or impeller blocked by debris
Clean strainer and impeller
Airlock in discharge pipework
Ensure pump body is filled with water
Discharge hose is bent or kinked
Straighten discharge hose
Damage caused by dirty or abrasive water
Clean pump and replace parts
Excessive friction loss or delivery head
Increase pipe size and increase pump size.
Pump will not turn off
Float switch jammed up
Free switch and move pump
Excessive friction loss or delivery head
Increase pipe size and increase pump size.
Pump switches off after
short period
Thermal overload has tripped
Ensure impeller is not clogged
Ensure water temperature is below 35 deg C
Ensure pump not operating on extension lead
Ensure pump not operating at low flow

C
A
B
C
A
B
Dimensions (mm)
Model
A
B
C
BIA-B10A
132
186
304
BIA-B15A
132
186
304
BIA-B25A
131
196
314
BIA-B40A
143
224
350
BIA-B75A
173
289
488
BIA-B15VA
132
186
304
BIA-B25VA
131
196
314
BIA-B40VA
143
224
350
BIA-B75VA
155
260
435
BIA-B75KA
195
280
420
BIA-B120G
198
237
540

BIA-B42A Dimensions

Terms & Conditions
White International Pty Ltd
Limited Product Warranties
TERMS & CONDITIONS
This warranty is given in addition to the consumer guarantees found within the Australian
Competition and Consumer Act 2010 (Cth) for goods purchased in Australia and the Consumer
Guarantees Act 1993 NZ for goods purchased in New Zealand:
1) White International Pty Ltd / White International NZ Ltd (White International) warrant that all
products distributed are free from defects in workmanship and materials, for their provided
warranty period as indicated on the top or opposite side of this document. Subject to the
conditions of the warranty, White International will repair any defective products free of charge
at the premises of our authorised service agents throughout Australia and New Zealand if a
defect in the product appears during the warranty period. If you believe that you have
purchased a defective product and wish to make a claim under this warranty, contact us on our
Sales Hotline on 1300 783 601, or send your claim to our postal address or fax line below and
we will advise you as to how next to proceed. You will be required to supply a copy of your proof
of purchase to make a claim under this warranty.
2) This warranty excludes transportation costs to and from White International or its appointed
service agents and excludes defects due to non-compliance with installation instructions,
neglect or misuse, inadequate protection against the elements, low voltage or use or operation
for purposes other than those for which they were designed. For further information regarding
the suitability of your intended application contact us on our Sales Hotline on 1300 783 601. If
you make an invalid claim under this warranty, the original product will be sent back to you
unrepaired.
3) This warranty refers only to products sold after the 1st January 2012, and is not transferable to
another product type and only applies to the original owner, purchaser or end user, and is in
addition to the consumer guarantees found within the Competition and Consumer Act 2010
(Cth) for goods purchased in Australia and the Consumer Guarantees Act 1993 (NZ) for goods
purchased in New Zealand.
4) Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
2 YEAR WARRANTY

5) To the fullest extent permitted by law, White International excludes its liability for all other
conditions or warranties which would or might otherwise be implied at law. To the fullest extent
permitted by law, White International’s liability under this warranty and any other conditions,
guarantees or warranties at law that cannot be excluded, including those in the Competition and
Consumer Act 2010 (Cth), is expressly limited to:
(a) in the case of products, the replacement of the product or the supply of equivalent
product, the payment of the cost of replacing the product or of acquiring an equivalent
product or the repair of the product or payment of the cost of having the product
repaired, is at the discretion of White International or a 3rd party tribunal elected under
the Competition and Consumer Act 2010 (Cth) for goods purchased in Australia and the
Consumer Guarantees Act 1993 (NZ) for goods purchased in New Zealand; and
6) To the fullest extent permitted by law, this warranty supersedes all other warranties attached to
the product or its packaging.
7) In the case of services, supplying the services again or the payment of the cost of having the
services supplied again, is at the discretion of White International or a 3rd party tribunal elected
under the Competition and Consumer Act 2010 (Cth) for goods purchased in Australia and the
Consumer Guarantees Act 1993 (NZ) for goods purchased in New Zealand.
8) Our warranty commences from the date of purchase of the above mentioned pumps. Proof of
purchase is required before consideration under warranty is given. Record your date of
purchase in the space below and retain this copy for your records.
Date of Purchase .......................................................... Model Purchased ..............................................
WHITE INTERNATIONAL PTY LTD
ABN 48 000119380 WHITE INTERNATIONAL NZ LTD
52-60 Ashford Ave, MILPERRA NSW 2214 138 Hugo Johnston Dr PENROSE, AUCKLAND, NZ
PO BOX 304, MILPERRA LPO NSW 2214 PO BOX 12704, PENROSE, AUCKLAND
Ph: 02 9783 6000 Fax: [phone] Ph: 09 579 977 Fax: [phone]
Customer Service Hotline: [phone] Customer Service Hotline: [phone]
Customer Service Faxline: 02 9783 6003 Customer Service Faxline: 0800 804 344
EMAIL: Sales Enquiries: [e-mail] EMAIL: General Info Enquiries: sal[email protected]o.nz