Bien-Air Dental Chiropro L Reference guide

BIEN-AIR DENTAL SA CHIROPRO SU 824-107 Rev.0004
SWITZERLAND AFTER SALES CHECKING PROCEDURE
Appr.: [AV] / [LTe] 1/7 [RE] / 20.10.14
Modifié le
Reference:
Serial No.:
Company
name:
Product:
APPLICATION DOMAIN
Checking protocol applies to the following devices:
Chiropro L, reference 1600613 Chiropro, reference 1600724
Chiropro L, USA, reference 1600679 ProImplant, USA, reference 1600730
Osseocare, référence 1600871 Osseocare US, référence 1600872
CHECKING CRITERIA
Y = Yes N = No
POS
PROCEDURE
Y
N
1.
Connect the peripherals for the set to be tested to the control unit:
The pedal, the cable and its motor and the CA20:1 L contra-angle.
When the device is not accompanied by the peripherals, these must be replaced with new
parts or parts in perfect condition for the duration of the test.
Connect the Bien-Air device to the electricity supply using the appropriate cable.
2.
Simultaneously:
Press the 3 buttons
ESC
and switch on the device
(switch to position - I -)
3.
The screen shows:
CHIROPRO L, reference 1600613
Check the software version: must be 1.03 or above.
4.
Press the Ok button to continue.
5.
The screen should appear as follows:

BIEN-AIR DENTAL SA CHIROPRO SU 824-107 Rev.0004
SWITZERLAND AFTER SALES CHECKING PROCEDURE
Appr.: [AV] / [LTe] 2/7 [RE] / 20.10.14
6.
Press the 4 buttons shown opposite in turn.
Check the correspondence between the display on
the screen and the button activated.
7.
As soon as all the buttons have been tested, the
message "Ok: Continue" will appear.
8.
Press the Ok button to continue.
9.
Adjust the screen contrast using the following
buttons: .
Set the contrast to the minimum that still allows the
information displayed to be read.
Confirm with Ok to continue.
10.
Now set the contrast to the maximum using the
following buttons: .
Confirm with Ok to continue.
11.
Set the optimum contrast using the following
buttons: .
Confirm with Ok to continue

BIEN-AIR DENTAL SA CHIROPRO SU 824-107 Rev.0004
SWITZERLAND AFTER SALES CHECKING PROCEDURE
Appr.: [AV] / [LTe] 3/7 [RE] / 20.10.14
12.
Test the pedal by following the steps below:
1. Blue button: press and check the
correspondence with the screen (IRRIG)
2. Orange button, press and check
correspondence (PROGR)
3. Grey button, press and check
correspondence (REV)
4. Pedal rocker, press and check
correspondence (PEDALE)
13.
Confirm with Ok to continue.
14.
Depress the pedal fully.
15.
Press the Ok button, and hold
until
"OK : continue" is displayed.
Release the pedal and then press the Ok button.
16.
Test with the pedal released: Press the Ok button.
17.
As soon as the test is completed, press
the Ok button.

BIEN-AIR DENTAL SA CHIROPRO SU 824-107 Rev.0004
SWITZERLAND AFTER SALES CHECKING PROCEDURE
Appr.: [AV] / [LTe] 4/7 [RE] / 20.10.14
18.
The screen must show the same image as the
photo opposite.
If necessary, use the arrows to set the different
parameters.
19.
Checking the direction of rotation and the light.
See various models to proceed.
20.
Checking the direction of rotation:
Depress the pedal to check the default direction of
rotation as indicated beside.
21.
CHIROPRO L models with light,
reference 1600613 and USA reference 1600679 :
Check there is a bright white light.
22.
Increase the speed to 500 rpm.
23.
Check that the direction of rotation is reversed.
Press the grey button on the pedal, start the motor
and check to hear "beep" and to see the "R "
symbol on the screen.
Check that the bur's direction of rotation is
reversed in relation to point 21.1.
24.
Press the grey button on the pedal to revert to the default direction of rotation.
25.
Practice on a material test block.
Check the bur's speed decline in relation with
force.
No error messages should appear on the device
during the test.

BIEN-AIR DENTAL SA CHIROPRO SU 824-107 Rev.0004
SWITZERLAND AFTER SALES CHECKING PROCEDURE
Appr.: [AV] / [LTe] 5/7 [RE] / 20.10.14
26.
Insert an irrigation line into the pump.
27.
Close the cover.
28.
Check the operation of the peristaltic pump with an irrigation line.
Adjust the pump to maximum.
29.
Fill the container with fresh water and place the
line's white end piece in it.
Important: the hose must not be pinched.
The end piece must be completely submerged.
Verification:
To start with, place the other end of the hose in the
recipient. Depress the pedal until water is regularly
expelled without any air, then stop.
30.
Now place this end in the measuring beaker.
Recommendation:
Use a high narrow beaker with a capacity which
allows 5 to 50 ml to be accurately measured, in
increments of one ml.
See the example in the photo opposite.

BIEN-AIR DENTAL SA CHIROPRO SU 824-107 Rev.0004
SWITZERLAND AFTER SALES CHECKING PROCEDURE
Appr.: [AV] / [LTe] 6/7 [RE] / 20.10.14
31.
Time 15 seconds of operation, with the pedal
depressed.
32.
Measure the quantity of water ejected into the
measuring beaker.
The required quantity is 35 ml ± 5 ml
in 15 seconds.
33.
Once the test is done, make the pump turn during three minutes at maximum flow with an
irrigation line placed in the pump.
34.
Check manually that each roller turns freely. If one roller does not turn freely, replace the
roller support REF 1501112-001.
35.
Press the Ok button.
36.
The screen CHIROPRO L, ref 1600613 indicate
Until software version 1.04 
Version 1.05 or above 
Then press Ok again.
Skip to 39.
5. TEST ENDO
37.
End of the tests.
38.
The screen shows:
CHIROPRO L, reference 1600613.
39.
Switch off the device (switch in position -O-).

BIEN-AIR DENTAL SA CHIROPRO SU 824-107 Rev.0004
SWITZERLAND AFTER SALES CHECKING PROCEDURE
Appr.: [AV] / [LTe] 7/7 [RE] / 20.10.14
40.
Finally proceed to Electrical test according to EN60601-1 (EARTH connection, LEAK-
AGE CURRENTS, AUXILIARY, CURRENT TO THE PATIENT as per IEC 60’601-§19).
The link between the inspection report and repair form is the responsibility of the
repairer.
Bien-Air Subsidiaries: Please refer to checking instruction IC 751-005-EN
41.
Traceability :
Complete and archive the documents SU 824-xxx and IC 751-015_xx in either electronic
or paper format. Any returns to Bien-Air Switzerland must include a copy of completed
form.
CERTIFICATE OF CONFORMITY
Name and visum:
Date :
Remarks:
DOCUMENT APPROVED BY :
NAME:
DATE :
SIGNATURE :