Biesemeyer T-Square 2 User manual

T-Square®Commercial Fence System Type 2
Français (14)
Español (26)
INSTRUCTIVO DE OPERACIÓN, CEN-
TROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
T-Square®Système commercial de guide Type 2
T-Square®Sistema de guía comercial Tipo 2
Instruction manual
Manuel d’utilisation
Manual de instrucciones
www.DeltaMachinery.com

2
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS
Read all warnings and operating instructions before using any tool or equipment. When
using tools or equipment, basic safety precautions should always be followed to reduce the risk of
personal injury. Improper operation, maintenance or modification of tools or equipment could result
in serious injury and property damage. There are certain applications for which tools and equipment
are designed. Biesemeyer strongly recommends that this product NOT be modified and/or used for any application
other than for which it was designed.
If you have any questions relative to its application DO NOT use the product until you have written Biesemeyer®and we have
advised you. Contact us online at www.DeltaMachinery.com or by mail at Technical Service Manager, Biesemeyer®, 99 Roush
Street Anderson, SC 29625.
Information regarding the safe and proper operation of this tool is available from the following sources:
• Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851or online at www.powertoolinstitute.org
• National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201
• American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 01.1
Safety Requirements for Woodworking Machines
• U.S. Department of Labor regulations www.osha.gov
SAVE THESE INSTRUCTIONS!
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury.
Used without the safety alert symbol indicates a potentially hazardous situation which, if not
avoided, may result in property damage.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear NIOSH/
OSHA approved, properly fitting face mask or respirator when using such tools.
IMPORTANT SAFETY INSTRUCTIONS.......................2
SAFETY GUIDELINES - DEFINITIONS .......................2
GENERAL SAFETY RULES .........................................3
FUNCTIONAL DESCRIPTION......................................4
CARTON CONTENTS ...................................................4
ASSEMBLY ....................................................................6
TROUBLESHOOTING................................................ 15
MAINTENANCE.......................................................... 15
SERVICE..................................................................... 15
ACCESSORIES .......................................................... 15
WARRANTY................................................................ 16
FRANÇAIS.................................................................. 17
ESPAÑOL ................................................................... 32
SAFETY GUIDELINES - DEFINITIONS

3
1. For your own safety, read the instruction manual
before operating the machine. Learning the machine’s
application, limitations, and specific hazards will greatly
minimize the possibility of accidents and injury.
2. Wear eye and hearing protection and always use safety
glasses. Everyday eyeglasses are not safety glasses. Use
certified safety equipment. Eye protection equipment should
comply with ANSI Z87.1 standards. Hearing equipment should
comply with ANSI S3.19 standards.
3. Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry which may get
caught in moving parts. Nonslip protective footwear is
recommended. Wear protective hair covering to contain long
hair.
4. Do not use the machine in a dangerous environment. The use
of power tools in damp or wet locations or in rain can cause
shock or electrocution. Keep your work area well-lit to prevent
tripping or placing arms, hands, and fingers in danger.
5. Maintain all tools and machines in peak condition. Keep
tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories. Poorly
maintained tools and machines can further damage the tool or
machine and/or cause injury.
6. Check for damaged parts. Before using the machine, check
for any damaged parts. Check for alignment of moving parts,
binding of moving parts, breakage of parts, and any other
conditions that may affect its operation. A guard or any other
part that is damaged should be properly repaired or replaced
with Delta or factory authorized replacement parts. Damaged
parts can cause further damage to the machine and/or injury.
7. Keep the work area clean. Cluttered areas and benches invite
accidents.
8. Keep children and visitors away. Your shop is a potentially
dangerous environment. Children and visitors can be injured.
9. Reduce the risk of unintentional starting. Make sure
that the switch is in the “OFF” position before plugging in the
power cord. In the event of a power failure, move the switch to
the “OFF” position. An accidental start-up can cause injury. Do
not touch the plug’s metal prongs when unplugging or plugging
in the cord.
10. Use the guards. Check to see that all guards are in place,
secured, and working correctly to prevent injury.
11. Remove adjusting keys and wrenches before starting the
machine. Tools, scrap pieces, and other debris can be thrown
at high speed, causing injury.
12. Use the right machine. Don’t force a machine or an attachment
to do a job for which it was not designed. Damage to the
machine and/or injury may result.
13. Use recommended accessories. The use of accessories and
attachments not recommended by Delta may cause damage to
the machine or injury to the user.
14. Use the proper extension cord. Make sure your extension cord
is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage,
resulting in loss of power and overheating. See the Extension
Cord Chart for the correct size depending on the cord length
and nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord.
15. Secure the workpiece. Use clamps or a vise to hold the
workpiece when practical. Loss of control of a workpiece can
cause injury.
16. Feed the workpiece against the direction of the rotation of the
blade, cutter, or abrasive surface. Feeding it from the other
direction will cause the workpiece to be thrown out at high
speed.
17. Don’t force the workpiece on the machine. Damage to the
machine and/or injury may result.
18. Don’t overreach. Loss of balance can make you fall into a
working machine, causing injury.
19. Never stand on the machine. Injury could occur if the tool tips,
or if you accidentally contact the cutting tool.
20. Never leave the machine running unattended. Turn the power
off. Don’t leave the machine until it comes to a complete stop.
A child or visitor could be injured.
21. Turn the machine “OFF”, and disconnect the machine from
the power source before installing or removing accessories,
changing cutters, adjusting or changing set-ups. When making
repairs, be sure to lock the start switch in the “OFF” position.
An accidental start-up can cause injury.
22. Make your workshop childproof with padlocks, master
switches, or by removing starter keys. The accidental start-up
of a machine by a child or visitor could cause injury.
23. Stay alert, watch what you are doing, and use common sense.
Do not use the machine when you are tired or under the
influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in injury.
24. Use of this tool can generate and disburse
dust or other airborne particles, including wood dust,
crystalline silica dust and asbestos dust. Direct particles away
from face and body. Always operate tool in well ventilated
area and provide for proper dust removal. Use dust collection
system wherever possible. Exposure to the dust may cause
serious and permanent respiratory or other injury, including
silicosis (a serious lung disease), cancer, and death. Avoid
breathing the dust, and avoid prolonged contact with dust.
Allowing dust to get into your mouth or eyes, or lay on your
skin may promote absorption of harmful material. Always use
properly fitting NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure, and wash exposed areas
with soap and water.
GENERAL SAFETY RULES
Failure to follow these rules may result in serious personal injury.

4
FUNCTIONAL DESCRIPTION
CARTON CONTENTS
FOREWORD
The BIESEMEYER®T-SQUARE®Commercial Fence System includes the fence assembly, front rail, rear rail, front guide tube,
extension table and legs along with the mounting hardware for assembling the fence system to your table saw.
The 52” fence is made up of 52” (1, 3 m) black rails (78-055B Type 2), 44” (1, 1 m) black table board (78-918B Type 2) and
fence body (78-919B Type 2).
The 36” fence is made up of 36” (914 mm) black rails (78-918B Type 2), 36” (914mm) black table board (78-918B Type 2) and
fence body (78-919B Type 2).
NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual are
representative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique
only.
1. Guide Tube
2. Front Rail
3. Rear Rail
(Separate Carton)
FIG. 1
32
1
5
4
4. Fence Body
5. Table Legs (2)

5
CARTON CONTENTS
FIG. 2
1 2
3
4
5
8
6
7
10
1. For Attaching Rear Rail to Saw
• Screw 3/8-24 x 1-1/4” (2)
• Lock Washer 3/8 (2)
• Flat Washer 3/8” (2)
• Hex Nut 3/8-24 (2)
2. For Attaching Front Rail to Extension Table
• Screw 1/4”-20 x 1-1/2” (14)
• Flat Washer ¼ x .81 O.D. (14)
• Lock Washer (14)
• Hex Nut 1/4”-20 (14)
3. For Attaching Front Rail to Saw Table
• Screw 5/16”-18 X 1” (2)
• Lock Washer 5/16 (2)
• Hex Nut 5/16”-18 (2)
4. For Attaching Guide Tube to Front Rail
• Screw 1/4-20 X 1/2 Button HD (8)
• Lock Washer (8)
5. For Attaching Rear Rail to Table
• Screw 1/4”-20 X 1-1/2 Hex HD (10)
• Flat Washer 1/4 x .81 O.D. (10)
• Flat Washer 1/4 (6)
• Lock Washer 1/4 (10)
• Hex Nut 1/4-20 (10)
6. For Attaching Table to Wing
• Hex Head Screw 5/16-18 x 3/4” (4)
• Flat Washer 5/16 (4)
7. Adjustable Feet for Table Legs
• Foot (2)
• Hex Nut 3/8”-16 (2)
8. For Attaching Legs to Table
• Self Tap Screw #8 x 3/4 (8)
• Pan HD Screw 10-32 x 1-3/4” (4)
• Flat Washer (4)
• Hex Nut 10-32 (4)
9. Guide Tube Template
10.Cursors
• Cursor (2)
• Screw #10 x 3/8 Pan HD Philips (4)
• Flat Washer #10 (4)
11.Handle Assembly
• Cap (2)
• Handle Sleeve (1)
• Screw 5/16-18 x 3 1/2”
9
11

6
FRONT RAIL TO SAW
1. Assemble front rail (A) Fig. 3 to the front edge of the saw
table using the two 5/16-18 x 1” long flat head Phillips
screw, flat washer, 5/16” lock washer and 5/16-18” hex nut
(B) supplied. Screws are inserted throught the two larger
countersunk holes in the front rail and into the two holes in
the front of the saw table and fastened with the lock washer
and hex nut. Do not tighten front rail mounting hardware at
this time.
2. Using template (C) Figs. 3 & 4, Check and adjust the front
rail on both sides of the saw blade as shown, to make sure
the rail is parallel with the table surface. The horizontal
portion of the rail should be down from the top of the table
surface 2-27/32”.
ASSEMBLY
FIG. 3
FIG. 4
C
B
A
C
78-055BT2 or 78-138BT2 Rails to Unisaws

7
REAR RAIL TO SAW
NOTE: DO NOT USE TEMPLATE TO SET REAR RAIL.
3. Align the two holes in the rear rail with the two holes in
the rear edge of the saw table.
Fasten rear rail to the saw as follows:
4. Thread the two 3/8-24 x 1-1/4” long hex head screw and
lock washer (D), supplied, Fig. 5, through the two holes in
the rail and into the two threaded holes in the saw table.
TABLE LEGS TO TABLE BOARD
5. Assemble the 3/8” jam nut (G) onto
leveling screw (H). Thread leveling
screw into bottom of support leg. Fig. 6
illustrates the foot leveling assembly on the table leg.
Assemble the remaing foot assembly to the other leg in
the same manner. NOTE: Height adjustment will be made
later.
6. Lay the table upside down on the floor or on a bench.
ASSEMBLY
FIG. 5
FIG. 6
D
H G

8
7. Position the table leg (I) to the closed in corner of the
extension table (J) as shown in Fig. 7. The vertical wall of
the angle plate should be against the end wall of the fence
table (section running from front to back of saw).
8. Attach the table leg to the table board with four #8 x 1/2”
self-tapping screws (K). Carefully drill through the holes
in the vertical plate and table edge with a 1/4” drill. Using
the #10-32 x 1-3/4” pan head screws, 2 flat washers (one
inside and one outside) and #10-32 hex nuts, bolt the legs
solidly to the fence. Repeat this process for the remaining
leg.
9. Loosely insert 4 3/8”-16 x 1” hex head screws and 3/8”
flat washers into the threaded holes in the extension
wing. Place table assembly (L) Fig. 8, in position between
the two rails, as shown. Make sure end of table is flush
against saw table (M). The mounting plate on the table
opposite of the legs will slide over the previously inserted
bolts. Hand tighten these bolts with the table in position.
Using a straight edge make sure table (L) is in the same
plane and level with saw table (M). Lightly tap up or down
and adjust leg leveling screws. When you are certain that
the table is level and in the same plane as the saw table,
tighten bolts. Using a bar clamp, clamp the opposite end
ASSEMBLY
of the table between the front and rear rails. Then drill
1/4” holes through the front and rear of the extension table
using holes (Q) provided in rails as a template. NOTE:
Number of holes (Q) in the front and rear rails will vary
depending on the length of the rails you purchased.
10. After the holes have been drilled in the edge of the front
and rear extension table board, fasten front rail to table
using the 1/4-20 x 1-1/2” flat head Phillips screws, flat
washers, lock washers and hex nuts (R). Fasten the rear
rail to the table board using 1/4”-20 x 1-1/2” hex head
screw, two flat washers (one inside and one outside), lock
washer and hex nut.
11. Lay the guide tube (B) Fig. 10, on the saw table as shown,
and line up the threaded holes (S) on the bottom of guide
tube with the through holes (T) on the front rail.
12. Position the guide tube (B) on the front rail and fasten the
guide tube to the rail using the 1/4-20 x 1/2” long button
head screws and lock washers.
FIG. 7
J I
K
B S
T
FIG. 9
R
LM
Q
FIG. 8
FIG. 10

9
FENCE ASSEMBLY AND ADJUSTMENT
1. Place fence clamp handle end cap (OO) Fig. 11 on post
(PP). Then place fence clamp handle body (QQ) on end
cap (OO) and place other end cap (SS) on body (QQ). Place
fence clamp handle screw (TT) into end cap (SS) all the way
down and tighten into post (PP). Finished handle should
look like (RR).
2. Align fence side (C) Fig. 12, with the miter slot on the table
saw and lock fence in position. Using a measuring tape (D),
measure the distance from the saw blade to the fence side.
3. WITHOUT MOVING THE FENCE, attach hairline pointer (E),
Fig. 13 to fence crossarm (F) using two #10-32 x 3/8” round
head screws and flat washers (G). Screws go through the
slotted holes in the pointer and into the threaded holes (H)
in the crossarm. Using the measurement from Step 2, align
the black line in the pointer to the same measurement on
the guide tube tape and securely tighten screws.
IMPORTANT: CHECK TO MAKE CERTAIN THAT
THE MITER GAGE SLOTS IN THE SAW TABLE ARE
PARALLEL WITH THE SAW BLADE. CHECK WITH THE
INSTALLATION MANUAL THAT CAME WITH YOUR
SAW FOR INSTRUCTIONS.
4. The fence (C) Fig. 14, must be adjusted so it is parallel
to the miter gage slot. Slide the fence until the bottom
edge is in line with the edge of the miter gage slot and
push down on locking handle (B). Check to see if the
fence (C) is aligned with the miter slot the entire length
of the table. If an adjustment is needed, lift fence (C) off
the guide as shown in Fig. 15. Slightly tighten or loosen
adjusting screws (J) or (K), using a 3/16” Allen wrench, not
included. Replace the fence on the guide tube and check
again. Repeat this adjustment until you are certain the
fence is parallel to the miter gage slot. NOTE: Very little
movement of the adjusting screws is necessary to
adjust the fence.
ASSEMBLY
FIG. 12
C
D
FIG. 13
G
E
H
F
OO
PP
QQ SS
RR
TT
FIG. 11
FIG. 14
C
B

10
5. When the fence locking handle (B) Fig. 16, is pushed to the
down position, the fence assembly (C) should be completely
clamped to the guide tube. If the fence assembly (C) is
not completely clamped to the guide tube when the handle
is pushed down, as shown, lift up handle (B) and raise fence
off the guide tube as shown in Fig. 15. Slightly tighten the
two adjusting screws (J) and (K) (if the fence is too loose) or
loosen (if the fence is too tight), using a 3/16” Allen wrench,
not supplied. NOTE: Screws (J) and (K) should be tightened
or loosend an equal amount. Replace the fence back on
the guide tube and recheck to see if the fence assembly
is completely tightened to the guide tube with the locking
handle (B) pushed down. Adjust further if necessary.
IMPORTANT: AFTER ADJUSTING THE FENCE
CLAMPING ACTION, RECHECK TO SEE THAT THE
FENCE IS STILL PARALLEL TO THE MITER GAGE
SLOT AND ADJUST AS NECESSARY.
6. When clamping the fence assembly (C) to the guide tube,
ASSEMBLY
make certain the camfoot (P), Fig. 17, is hanging down and
against the locking handle (B), and not caught on top of the
guide tube.
7. To move the fence along the guide tube, simply lift up the
locking handle (B) Fig. 18, as shown, slide the fence to
the desired position on the guide, and push down locking
handle (B) Fig. 16 as shown, to lock in position. NOTE: A
magnet is provided to hold the handle in the up
position when moving the fence.
FIG. 15
J K
FIG. 18
B
FIG. 16
B
C
FIG. 17
B C
P

11
8. The distance the fence is positioned away from the saw
blade is indicated by the witness line (S) located in cursor
(E), Fig. 19. To calibrate the cursor to the saw blade, make
a test cut with the fence locked in position. Measure the
width of the cut piece. Adjust the cursor by loosening screws
(G), adjusting the cursor until the witness line is aligned
with the same marking on the scale as the cut piece.
Tighten the two screws (G). Repeat until the width of the cut
piece matches the measurement indicated by the witness
line.
ASSEMBLY
9. Apply grease to locking handle (B) and camfoot (P) Fig.
20, monthly to insure long lasting smooth operation.
10. Apply paste wax to the fence sides and the unpainted
guide tube sliding surfaces weekly. Meguiar’s Professional
Paste Wax (M-2611) is recommended. Also, saw table and
extension table surface should be waxed.
FIG. 19
G
E
S
FIG. 20
P
B

12
ASSEMBLY
CONSTRUCTING EXTENSION TABLE (IF NOT SUPPLIED)
To reduce the risk of injury, turn unit off and disconnect it from power source before installing and
removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.
78-150T2 OR 78-130T2 RAILS ASSEMBLY
(FOR ALL OTHER SAWS)
ASSEMBLE FRONT RAIL
1. Raise saw blade (A) Fig.22. Place a straight edge (B)
against the right side of saw blade extending out over the
front of the saw as shown. Position front rail (C) against
the edge of saw table and lightly clamp in place using
bar clamps (D). Align notch (E) in front rail (C) with the
straight edge (B) as shown. NOTE: Any portion of the
notch needs to align with the straight edge. Final
calibration will be explained later.
2. Using template (F) Fig.23, check and adjust the front rail at
both sides of saw table, to make sure the horizontal portion
of front rail (C) is parallel with the table top and then
tighten bar clamps. The rail should be down from
the top of the table 2-27/32”.
3. When you are certain front rail (C) is level with the table
surface, drill four 1/4” through holes into the saw table
using the 1/4” counter sunk holes in the front rail as a
template. IMPORTANT: Before drilling, check to
make certain there is no interferance such as
casting ribs behind front edge of saw table.
4. Fasten front rail (C) to saw table using the four 1/4-20 x
1-1/4” long flat head screws, flat washers, lock washers
and hex nuts supplied.
FIG. 21
A
B
C
D
E
FIG. 22
F
C
FIG. 23

13
ASSEMBLY
ASSEMBLE REAR RAIL
5. Clamp rear rail (G) Fig. 24, to back of saw table using bar
clamps making certain notch (E) in rail is aligned with saw
blade (A) as shown, using straight edge (B). Make sure the
two cutouts in the rail are below the bottom of the miter
slots in the saw table.
6. Check to make certain there are no interferance such as
casting ribs behind the rear edge of the saw table and
drill a minimum of two through holes into the saw table
using the countersunk holes as a template. Fasten rear
rail to saw table using the 1/4-20 x 1-1/4” long flat head
screws, flat washers, lock washers and hex nuts supplied.
IMPORTANT: If there is no room in rear edge of the
table to drill through holes, it will be necessary to
drill #7 holes and tap holes with a 1/4-20 tap.
7. After fastening the rear rail to the saw table, tilt the saw
blade to make certain there is no interferance between the
saw guard and the rear rail. If there is, it will be necessary
to enlarge the cut-out (H) Fig. 24, in the rear rail.
EXTENSION TABLE & SUPPORT LEGS
8. Assemble the 3/8” jam nut (I) onto leveling screw (J).
Thread leveling screw into foot adapter. Fig. 25 illustrates
the foot leveling assembly on the table leg. Assemble
the remaining foot assembly to the other leg in the same
manner. NOTE: Height adjustments will be made
later.
IMPORTANT: If your saw fence system will be used
with a mobile base underneath the saw base and table
legs, the position of the legs will have to be changed
to fit the mobile base extension.
9. Lay the extension table upside down on a floor or bench.
10. Position table leg (K) to the closed in corner of the
extension table (L), as shown in Fig. 26
11. Attach the table leg (K) to the table board (L) with six
5/8” long wood screws (M). Repeat this process for the
remaining leg.
IMPORTANT: If your saw fence system will be used
with a mobile base underneath the saw base and table
legs, the position of the legs will have to be changed
to fit the mobile base extension.
12. Place table assembly (L) in position between the front
and rear rail, as shown in Fig. 27. Make sure end of table
is flush against saw table and using a bar clamp, snug
up ends of rails to hold table in position. Using a straight
edge, (N), make certain table is in the same plane and
level with saw table. Adjust leveling screws in bottom of
support legs to accomplish this. When you are certain
table is level and in the same plane as the saw table,
tighten bar clamp to hold everything in position. Then drill
1/4” through holes through the front and rear table frame
using holes (O) in the rail as a template. The number of
holes to drill will depend on the length of the rails.
FIG. 24
FIG. 25
FIG. 26
FIG. 27
I
J
A
B
G
E
H
K
L
M
L
N
O

14
ASSEMBLY
P
Q
R
S
FIG. 28
FIG. 29
13. After the holes have been drilled in the front and rear table
frame, fasten both front and rear rail to table Fig. 28 using
the 1/4-20 x 1-1/2” long flat head screws, fender washers
and hex nuts (P) provided.
14. Lay guide tube (Q) Fig. 29, on saw table as shown, and
line up the threaded holes (R) in bottom of guide tube with
through holes (S) in the front rail. Guide tube will extend
6” past the rail at both ends.
15. Lay guide tube on front rail and fasten the guide tube to
the front rail using the 1/4-20 x 1/2” long hex screws and
lockwashers provided. NOTE: Where there are two
holes 2-1/2” apart, use only one of the holes.

15
TROUBLESHOOTING
For assistance with your machine, visit our website at www.DeltaMachinery.com for a list of service centers or call the
Biesemeyer®help line at 1-800-223-7278
MAINTENANCE
To reduce the risk of injury, turn unit off and disconnect it from power source before installing and
removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.
KEEP MACHINE CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER
use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air
LUBRICATION & RUST PROTECTION
Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially
available protective product designed for this purpose. Follow the manufacturer’s instructions for use and safety.
To clean cast iron tables of rust, you will need the following materials: a sheet of medium Scotch-Brite™ Blending Hand Pad, a can
of WD-40® and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad. Degrease the table,
then apply the protective product as described above.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our website at www.DeltaMachineryParts.com You
can also order parts from your nearest factory-owned branch, Authorized Warranty Service Center or by calling Technical Service
Manager at [phone] to receive personalized support from one of our highly-trained representatives.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about Biesemeyer®, its factory-
owned branches, or to locate an Authorized Warranty Service Center, visit our website at www.DeltaMachinery.com or call
our Technical Service Manager at [phone]. All repairs made by our service centers are fully guaranteed against defective
material and workmanship. We cannot guarantee repairs made or attempted by others. By calling this number you can also find
answers to most frequently asked questions 24 hours/day.
You can also write to us for information at Biesemeyer, 99 Roush Street Anderson, SC 29625 - Attention: Technical Service Manager.
Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, date code, etc.)
Since accessories other than those offered by Biesemeyer®have not been tested with this product,
use of such accessories could be hazardous. For safest operation, only Biesemeyer®recommended accessories
should be used with this product.
A complete line of accessories is available. Please visit our Web Site www.DeltaMachinery.com for a catalog or for the name of
your nearest supplier.
ACCESSORIES
SERVICE

16
WARRANTY
To register your tool for warranty service visit our website at www.DelttaMachinery.com.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country
specific warranty information contained in the packaging, call the local company or see website for warranty information.
TWO YEAR LIMITED WARRANTY
Delta® Power Equipment Corporation
1. WHAT IS COVERED. Delta Power Equipment Corporation (“Company”) will repair or replace, at its option, any new or factory refurbished
DELTA® accessory or service part which is purchased at retail in the United States or Canada and which in normal use has proven to be
defective in workmanship or material, subject to the conditions stated in this Limited Warranty. This Limited Warranty covers only materials
and labor. All transportation costs are Customer’s responsibility.
2. WARRANTY PERIOD. All warranty claims must be submitted within two from the date of retail purchase of the new accessory. For all service
parts and factory refurbished DELTA® accessories, the warranty period is 180 days.
3. HOW TO OBTAIN SERVICE. To obtain warranty service, you must return the defective product, at your expense, to a service center authorized
by Company to perform warranty service (a “DELTA® Authorized Service Center”) within the applicable warranty period, together with
acceptable proof of purchase, such as your original receipt bearing the date of purchase, or product registration number. Company reserves
the right to restrict warranty claim service to the country where the purchase was made and/or to charge for the cost to export service parts
or provide warranty service in a different country. On-line purchases are deemed made in the United States. For the location of your nearest
DELTA® Authorized Service Center, call Company’s Customer Care Center at [phone].
4. EXCLUSIONS.
· Company does not offer any warranty on products purchased in used or damaged condition.
· Company does not warranty any products purchased outside the United States or Canada
· Company will not be responsible for any damage that has resulted from normal wear, misuse, abuse or any repair or alteration made by
anyone other than a DELTA® Authorized Service Center or a designated representative of Company’s Customer Care Center.
· All IMPLIED WARRANTIES are expressly limited to the warranty period identified above.
· Under no circumstances will Company be liable for INCIDENTAL OR CONSEQUENTIAL damages.
· This limited warranty is Company’s sole warranty and sets forth the customer’s exclusive remedy with respect to defective products; all other
warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Company, except as
stated above.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or the limitation of implied warranties, so the
above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary
in certain states or provinces. For further details of warranty coverage and warranty repair information, call [phone]. To register your
products online, we encourage you to visit our website and register for a FREE DELTA Member Account at http://www.deltamachinery.com/
register.

17
MESURES DE SÉCURITÉ - DÉFINITIONS
Ce guide contient des renseignements importants que vous deviez bien saisir. Cette information porte sur VOTRE SÉCURITÉ et
sur LA PRÉVENTION DE PROBLÈMES D’ÉQUIPEMENT. Afin de vous aider à identifier cette information, nous avons utilisé
les symboles ci-dessous. Veuillez lire attentivement ce guide en portant une attention particulière à ces sections.
Indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera la mort ou des blessures
graves.
Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait se solder par un décès
ou des blessures graves.
Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée pourrait se solder par des
blessures mineures ou modérées.
Utilisé sans le symbole d’alerte à la sécurité, indique une situation potentiellement dangereuse qui, si elle n'est
pas évitée pourrait se solder par des dommages à la propriété.
LES INSTRUCTIONS IMPORTANTES DE SURETE
Lire toutes instructions d'avertissements et opération avant d'utiliser n'importe
quel outil ou n'importe quel équipement. En utilisant les outils ou l'équipement, les précautions de
sûreté fondamentales toujours devraient être suivies pour réduire le risque de blessure personnelle.
L'opération déplacée, l'entretien ou la modification d'outils ou d'équipement ont pour résultat la
blessure sérieux et les dommages de propriété. Il y a de certaines applications pour lequel outils et l'équipement
sont conçus. La Biesemeyer recommande avec force que ce produit n'ait pas modifié et/ou utilisé pour l'application
autrement que pour lequel il a été conçu.
En cas de questions à propos de l’application du produit, NE PAS l’utiliser avant d’écrire à Biesemeyer et d’obtenir nos conseils.
Il est possible de communiquer avec nous en ligne au www.DeltaMachinery.com ou par courrier postal au : Technical Service
Manager, Biesemeyer, 99 Roush Street Anderson, SC 29625.
Information en ce qui concerne l'opération sûre et correcte de cet outil est disponible des sources suivantes:
• Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 ou en ligne www.powertoolinstitute.org
• National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201
• American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 0 1 . 1
Safety Requirements for Woodworking Machines
• U.S. Department of Labor: www.osha.gov
Certaines poussières produites par les travaux de ponçage, de sciage, de meulage, de
perçage et par toute autre activité de construction contiennent des produits chimiques reconnus par l’État de la
Californie comme pouvant causer le cancer, des anomalies congénitales ou d’autres problèmes liés aux fonctions
reproductrices. Voici quelques exemples de ces produits chimiques :
• le plomb des peintures à base de plomb,
• la silice cristalline provenant des briques, du ciment et d’autres produits de maçonnerie ainsi que, et
• l’arsenic et le chrome issus du bois traité chimiquement.
Les risques reliés à l’exposition à ces produits chimiques varient selon la fréquence à laquelle l’utilisateur effectue
ce type de travail. Pour réduire l’exposition à ces produits chimiques : travailler dans un endroit bien ventilé et
porter un équipement de sécurité approuvé, notamment un masque antipoussières conçu spécialement pour filtrer
les particules microscopiques.
CONSERVER CES DIRECTIVES

18
1. Pour sa sécurité personnelle, lire la notice d’utilisation,
avant de mettre la machine. En marche, et pour aussi
apprendre l’application et les limites de la machine ainsi que les
risques qui lui sont particuliers ainsi, les possibilités d’accident
et de blessures seront beaucoup réduites.
2. Portez des dispositifs de protection des yeux et de l'ouïe.
Utilisez toujours des lunettes de sécurité. Des lunettes
ordinaires ne constituent pas des lunettes de sécurité. Utilisez
des équipements de sûreté homologués. Les dispositifs
de protection des yeux doivent être conformes aux normes
ANSI Z87.1. Les dispositifs de protection de l'ouïe doivent être
conformes aux normes ANSI S3.19.
3. Porter une tenue appropriée. Pas de cravates, de gants, ni de
vêtements amples. Enlever montre, bagues et autres bijoux.
Rouler les manches. Les vêtements ou les bijoux qui se trouvent
pris dans les pièces mobiles peuvent entraîner des blessures.
4. Ne pas utiliser la machine dans un environnement dangereux.
L’utilisation d’outils électriques dans des endroits humides ou
sous la pluie peut entraîner des décharges électriques ou une
électrocution. Garder la zone de travail bien éclairée pour éviter
de trébucher ou d’exposer les doigts, les mains ou les bras à une
situation dangereuse.
5. Garder les outils et les machines en parfait état. Garder les
outils affûtés et propres afin d’obtenir le meilleur et le plus sûr
rendement. Suivre les instructions pour lubrifier et changer les
accessoires. Les outils et les machines mal entretenus peuvent
se dégrader davantage, et/ou entraîner des blessures.
6. Inspecter les pièces pour déceler tout dommage. Avant
d’utiliser la machine, la vérifier pour voir s’il n’y a pas de pièces
endommagées. Vérifier l’alignement des pièces mobiles et si ces
pièces ne se coincent pas, la rupture de pièces, ou toute autre
condition pouvant en affecter le fonctionnement. Toute pièce
ou protecteur endommagé doit être réparé ou remplacé avec le
delta ou les pièces de rechange autorisées par usine. Les pièces
endommagées peuvent dégrader davantage la machine et/ou
entraîner des blessures.
7. Garder l’aire de travail propre. Les zones et établis encombrés
favorisent les accidents.
8. Garder les enfants et les visiteurs à distance. L’atelier est un lieu
potentiellement dangereux. Les enfants et les visiteurs peuvent
se blesser.
9. Éviter le démarrage accidentel. S’assurer que l’interrupteur
est sur « OFF » (arrêt) avant de brancher le cordon. En cas de
coupure de courant, placer l’interrupteur à la position « OFF »
(arrêt). Un démarrage accidentel peut entraîner des blessures.
10. Utiliser les dispositifs protecteurs. Vérifier que tous les dispositifs
protecteurs sont bien en place, bien fixés et en bon état de
marche pour éviter les blessures.
11. Enlever les clés de réglage et celles de serrage avant de mettre
la machine en marche. Les outils, les chutes et les autres débris
peuvent être projetés violemment et blesser.
12. Utiliser la bonne machine. Ne pas forcer la machine ou
l’accessoire à faire un travail pour lequel il n’a pas été conçu.
Des dommages à la machine et/ou des blessures pourraient
s’ensuivre.
13. Utiliser les accessoires recommandés. L’utilisation d’accessoires
non recommandés par Delta peut endommager la machine et
blesser l’utilisateur.
14. Utiliser le cordon prolongateur approprié. S’assurer que le cordon
prolongateur est en bon état. Lorsqu’un cordon prolongateur
est utilisé, s’assurer que celui-ci est d’un calibre suffisant
pour l’alimentation nécessaire à la machine. Un cordon d’un
calibre insuffisant entraînera une perte de tension d’où une perte
de puissance et surchauffe. Voir le Tableau sur Les Cordons
prolongateurs pour obtenir le calibre approprié selon la longueur
du cordon et l’ampérage de la machine. S’il y a un doute, utiliser
un cordon d’un calibre supérieur. Plus le chiffre est petit, plus le
fil est gros.
15. Fixer la pièce. Utilisez les brides ou l'étau quand vous ne
pouvez pas fixer l'objet sur la table et contre la barrière à la main
ou quand votre main sera dangereusement près de la lame (à
moins de 6").
16. Avancer la pièce dans le sens contraire à la rotation de la lame,
de la fraise ou de la surface abrasive. L’alimentation dans l’autre
sens peut entraîner une projection violente de la pièce.
17. Ne pas forcer la machine en avançant la pièce trop vite.
Des dommages et/ou des blessures peuvent s’ensuivre.
18. Ne pas se pencher au-dessus de la machine. Une perte de
l’équilibre peut entraîner une chute sur la machine en marche et
causer des blessures.
19. Ne jamais monter sur la machine. On peut se blesser gravement
si la machine bascule ou si l’on touche accidentellement son outil
tranchant.
20. Ne jamais laisser la machine en marche sans surveillance.
Couper le courant. Ne pas quitter la machine tant qu’elle n’est
pas complètement arrêtée. Un enfant ou un visiteur pourrait se
blesser.
21. Mettre la machine à l’arrêt « OFF » et la débrancher avant
d’installer ou d’enlever des accessoires, changer les coupeurs,
d’ajuster ou de changer des montages. En dépannant, soyez
sûr de fermer le commutateur de début en position de "off". Un
démarrage accidentel peut entraîner des blessures.
22. Mettre l’atelier à l’abri des enfants au moyen de cadenas,
d’interrupteurs principaux ou en enlevant les boutons des
dispositifs de mise en marche. Le démarrage accidentel de
la machine par un enfant ou un visiteur peut entraîner des
blessures.
23. Rester vigilant, attentif, et faire preuve de bon sens. Ne pas
utiliser la machine lorsque l’on est fatigué ou sous
l’influence de drogues, d’alcool ou de médicaments. Un
instant d’inattention lors de l’utilisation d’outils électriques peut
entraîner des blessures graves.
24. L'utilisation de cet outil peut produire
et disperser de la poussière ou d'autres particules en suspension
dans l'air, telles que la sciure de bois, la poussière de silicium
cristallin et la poussière d'amiante. Dirigez les particules loin
du visage et du corps. Faites toujours fonctionner l'outil dans
un espace bien ventilé et prévoyez l'évacuation de la poussière.
Utilisez un système de dépoussiérage chaque fois que possible.
L'exposition à la poussière peut causer des problèmes de santé
graves et permanents, respiratoires ou autres, tels que la silicose
(une maladie pulmonaire grave) et le cancer, et même le décès
de la personne affectée. Évitez de respirer de la poussière et de
rester en contact prolongé avec celle-ci. En laissant la poussière
pénétrer dans vos yeux ou votre bouche, ou en la laissant
reposer sur votre peau, vous risquez de promouvoir l'absorption
de substances toxiques. Portez toujours des dispositifs de
protection respiratoire homologués par niosh/osha, appropriés à
l'exposition à la poussière et de taille appropriée, et lavez à l'eau
et au savon les surfaces de votre corps qui ont été exposées.
RÈGLES DE SÉCURITÉ GÉNÉRALES
L’inobservation de ces règles peut conduire à des blessures graves.

19
DESCRIPTION FONCTIONNELLE
CONTENUS DE BOITE
DÉSEMBALLAGE ET NETTOYAGE
AVANT-PROPOS
Le système commercial de guide Biesemeyer®T-Square®comprend le module du guide, les barres de guidage avant et arrière,
et le tube avant du guide de même que la quincaillerie pour assembler le système de guide à différents types de scies de table.
Selon le modèle commandé, une trousse comprenant une patte accessoire pourrait également être livrée. Il faut également avoir
une rallonge à droite et des pattes de support. On peut acheter séparément la rallonge à droite ou utiliser le schéma fourni dans
le présent mode d’emploi pour en fabriquer une. Si la trousse comprenant la patte accessoire n’est pas incluse avec le guide, il
est également possible de la commander séparément. IMPORTANT : Le système commercial de guide Biesemeyer®T-Square®est
conçu pour une utilisation uniquement avec une rallonge et une trousse comprenant une patte accessoire.
REMARQUE : La image sur la couverture illustre le modèle de production actuel. Les autres illustrations de ce mode d’emploi ne sont
présentes qu’à titre indicatif et il est possible que les étiquettes et accessoires actuels diffèrent des caractéristiques réelles de ce
modèle. Ces illustrations ont uniquement pour but d’illustrer la technique.
1. Tube du guide
2. Barre de guidage avan
3. Barre de guidage arrière
(Carton Séparé)
FIG. 1
32
1
5
4
4. Guide carrée en T
(T-Square)
5. 2 tiges portantes

20
1 2
3
4
5
8
6
7
10
1. Quincaillerie pour fixer la barre de guidage
arrière à la scie
• Vis 3/8-24 x 1-1/4 po (2)
• 2 rondelles de blocage de 3/8
• Rondelle plate de 3/8” (2)
• Écrou hexagonal de 3/8 po-24 (2)
2. Pour fixer la traverse avant à la table
• Vis ¼ po-20 x 1-1/2 po (14)
• Rondelle plate ¼ x 0,81 de diamètre extérieur (14)
• 14 rondelles de blocage
• Écrou hexagonal de 1/4 po-20 (14)
3. Quincaillerie pour fixer la barre de guidage
avant à la scie
• Vis 5/16 po-18 X 1po (2)
• 2 rondelles de blocage de 5/16
• Écrou hexagonal de 5/16 po-18 (2)
4. Quincaillerie pour fixer le tube du guide à la
barre de guidage avant
• Vis à tête ronde haute résistance 1/4-20 x 1/2 (6)
• 8 rondelles de blocage
5. Pour fixer la traverse arrière à la table
• Vis hexagonale haute résistance 1/4-20 x 1½ (10)
• Rondelle plate ¼ x 0,81 de diamètre extérieur (10)
• Rondelle plate de 1/4 (6)
• 10 rondelles de blocage de 1/4
• Écrou hexagonal de 1/4-20 (10)
6. Quincaillerie pour fixer la rallonge de table au
volet de la scie Unisaw
• Vis à tête hexagonale de 5/16-18 x 3/4 po (4)
• Rondelle plate de 5/16 (4)
7. Pieds de la table réglables
• 2 pieds de nivellement
• Écrou hexagonal de 3/8 po-16 (2)
8. Quincaillerie pour fixer les pattes à la table
• Vis auto-taraudeuse no 8 x 3/4 (8)
• Vis à tête cylindrique haute résistance 10-32 x
1-3/4 po (4)
• 4 rondelles plates
• Écrou hexagonal de 10-32 (4)
9. Gabarit d’installation de barre de guidage
10.Curseurs
• 2 pointeurs fins
• Vis à tête cylindrique haute résistance Phillips no
10 x 3/8 (4)
• 4 rondelles plates #10)
11.Pièces de poignée serre-guide
• Chapeau (2)
• Manche de poignée (1)
• Vis 5/16-18 x 3 1/2 po
CONTENUS DE BOITE
FIG. 2
9
11