Big Air ICF72 Installation and operating instructions

CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.
DC CEILING FAN
MODELS ICF72, ICF96
- INSTALLATION
- OPERATION
- MAINTENANCE
- WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND OPERATION.
Made in Taiwan.

1 | P a g e
CONGRATULATIONS ON YOUR PURCHASE
Congratulations on purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power which
gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement and silent operation.
Energy Saving –The DC motor is the latest technology in fan design. Its highly efficient motor saves up to 65%
more energy than ceiling fans with traditional AC motors.
Silent Operation –This DC fan motor is programmed with a stabilized current which efficiently reduces motor noise.
Low Operating Temperature–The DC power is managed effectively which brings down the motor operating
temperature to less than 50degs. This results in a much cooler motor than a standard AC fan and increases the longevity
of the motor.
6 Speed Remote Control –While regular AC ceiling fans usually come with only 3 speeds, this DC fan comes
complete with a 6 speed remote, which gives greater choice of comfort levels.
SAFETY PRECAUTIONS
1) This appliance is NOT intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
2) Children should be supervised to ensure that they do not play with the appliance.
3) An all-pole disconnection switch must be incorporated in the fixed wiring in accordance with the wiring rules.
4) Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your health and well-being.
5) The structure to which the fan is to be mounted must be capable of supporting a weight of 90 lbs.
6) The fan should be mounted so that the blades are at least 7 ½ feet above the floor.
7) This fan is suitable for indoor and outdoor areas provided the fan is fully undercover with a minimum of 2 walls. The
ceiling fan must be positioned in a location protected from water, wind, dust and salt. Exposure to these elements
will void the warranty. Mounting the fan in a situation where it is subject to water or moisture is dangerous.
8) Only an authorized electrician should execute the installation.

2 | P a g e
BEFORE INSTALLATION
Unpack your fan and check contents. You should have the following:
Fig. 1
1Mounting bracket x 1 9Extra motor screws x 1 (not shown)
2Fan assembly with hanger cover,
down rod, canopy cover and canopy x 1 10 Blade screws x 28 (not shown)
3Blades x 9 11 Blade bracket kit screws x 10 (not shown)
4Blade holder x 1 12 Wooden screws x 2 (not shown)
5Blade bracket kit x 9 13 Balancing kits x 1 set (not shown)
6Blade decorative kit x 9 14 Screws for remote holder x 2 (not shown)
7Bottom cover x 1 15 12V Battery for remote x 1 (not shown)
8 Remote transmitter with holder x 1 set

3 | P a g e
TOOLS REQUIRED:
-Phillips / flat head screwdriver
-Pair of pliers
-Adjustable spanner
-Step ladder
-Wire cutter
INSTALLING THE FAN
-Wiring, supply cable as required by local provincial and national wiring codes and regulations.
INSTALLING THE MOUNTING BRACKET
The ceiling fan must be installed in a location so that the blades are 1 ft. spacing from the tip of the blade to the
nearest objects or walls.
Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 90lbs., with
two long screws provided. Ensure at least 1 ½ in. of the screw is threaded into the support.
Fig. 2
NOTE: The bracket screws provided are for use with wooden structures only. For structures other than wood,
the appropriate screw type MUST be used.
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 20 degree
angled ceiling installation.
Fig. 3
BEAM
MUST BE ABLE
TO SUPPORT UP
TO 90 LBS.

4 | P a g e
HANGING THE FAN MOTOR ASSEMBLY
Lift the fan assembly onto mounting bracket. Fig. 4
Ensure the notch of the ball joint is positioned on the stopper of the mounting bracket to prevent the fan from
rotating when in operation. Fig. 5
Fig. 4 Fig. 5
PREPARE AND COMPLETE THE ELECTRICAL WIRING —WIRING DIAGRAM (FIG. 6)
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A LICENSED
ELECTRICIAN.
NOTE: AN ADDITIONALALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED WIRING.
NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN ISOLATION
SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN PROGRAMMING THE REMOTE AND
RECEIVER TO PAIR TOGETHER.
Fig. 6
Stopper of bracket
Notch of ball joint
Mounting Bracket
120-110 VAC
SUPPLY

5 | P a g e
INSTALL CANOPY COVER
Loosen 2 screws from the bottom of the mounting bracket.
Slide the canopy up to the mounting bracket and place the key hole on the canopy over the screw on the
mounting bracket, turn canopy until it locks in place at the narrow section of the key holes, secure it by
tightening the two set screws. Avoid damaging the electrical wiring prepared previously.
Finally attach the canopy cover to canopy and secure it by pushing the lugs into the holes.
Fig. 7
BLADE INSTALLATION
Attach the blade holder to the motor bylining up the position label (1, Fig. 8) and secure it by tightening 6 screws
(Fig 9.)
Insert the blade screws through the blade assembly in the following order—blade holder, blade and blade
bracket kit. Then secure the blade to the blade holder by tightening the 3 screws (Fig. 10).
Push the blade decorative kit into the end of the blade and secure it by tightening the screw.
Repeat to install the other blades to the blade holder.
Finally install the bottom cover to the shaft of the motor by rotating it clockwise (Fig.11).
Fig. 8 Fig. 9

6 | P a g e
Fig. 10 Fig. 11
USING YOUR CEILING FAN
Pairing Transmitter and Receiver –when 2 or more DC ceiling fans are installed in one location
When two or more fans are located near each other, you may want to have the receiver/transmitter for each fan set to a
different code, so that the operation of one fan does not affect the operation of the other fans.
The DIP switches for the transmitter (remote hand piece) are located in the battery compartment of the transmitter.
Configuring the DIP switches will allow a unique transmission code assigned to each fan ceiling.
NOTE: Ensure that you have installed an all - pole disconnection switch in the fixed wiring for each fan, when using DIP
code function.
NOTE: Ensure power to the Receiver is ON prior to pairing the transmitter with the receiver.
Transmitter/Receiver pairing for ceiling fan 1:
Turn off both ceiling fans 1 and 2 via the mains supply to the receiver.
Slide the cover of the battery compartment of the transmitter to access the DIP switches. This will be transmitter
1.
Change the position of the DIP switches in the remote transmitter 1, so that it will be different to transmitter 2.
Fig. 8
Install the 12VDC battery in the compartment. Please make sure the polarity of the battery is correct.
Turn on the power to receiver 1. Keep the power OFF to receiver 2. (Each ceiling fan must have its own isolation
switch, so that only the ceiling fan that needs to be paired with the transmitter will be ON).

7 | P a g e
Press and hold the SET button of transmitter 1 for 6 seconds within 60 seconds of switching the power to the
receiver of ceiling fan 1.
Now the transmitter should be paired with the receiver of ceiling fan 1. Turn ON/OFF or change the speed of
ceiling fan 1 by the transmitter to check the operation.
Setting DC Ceiling fan 2:
Turn off both ceiling fans 1 and 2 via the mains supply to the receiver.
Slide the cover of the battery compartment of the transmitter to access the DIP switches. This will be transmitter
2.
Change the position of the DIP switches in the remote transmitter 2, so that it will be different to transmitter 1.
Fig. 8
Install the 12VDC battery in the compartment. Please make sure the polarity of the battery is correct.
Turn on the power to receiver 2. Keep the power OFF to receiver 1. (Each ceiling fan must have its own isolation
switch, so that only the ceiling fan that needs to be paired with the transmitter will be ON).
Press and hold the SET button of transmitter 2 for 6 seconds within 60 seconds of switching the power to the
receiver of ceiling fan 2.
Now the transmitter should be paired with the receiver of ceiling fan 2. Turn ON/OFF or change the speed of the
ceiling fan 2 by the transmitter to check operation.
Note: The pairing of Transmitter and Receiver is not required if only one ceiling fan is installed. When more than
two ceiling fans are installed near each other, please refer to the instruction above.
Fig. 8
Remote Control Buttons
○
1 - FAN SPEED CONTROL BUTTON:
There are 6 available speeds. ○
I button is for the lowest speed, and
○VI button is for the fastest speed.
NOTE: WHEN YOU TURN ON THE FAN FOR THE FIRST TIME OR
SWITCH THE MAIN POWER TO THE CONTROLLER, YOU NEED
TO START THE FAN ON HIGH “○ VI ”SPEED FIRST AND THEN
CHOOSE A LOWER SPEED.
Fig. 9

8 | P a g e
test
5-10 SECONDS IS REQUIRED TO ALLOW THE DC FAN TO RESPOND TO THE REMOTE EACH SPEED OR FAN
DIRECTION SELECTIONS, AS DC FANS INCORPORATE A SENSOR CONTROL WHICH CONTROLS THE POWER
TO THE MOTOR.
○
2 - FAN OFF BUTTON:
Press the button to turn the fan off.
○
3 - REVERSE FUNCTION BUTTON:
Press the button to activate the reverse running function. The fan must be operating to activate the reverse function.
THE RECEIVER PROVIDES THE FOLLOWING LEVEL OF PROTECTION AGAINST:
Lock position: the receiver has a built in safety feature to protect against obstruction during operation. The motor
will be locked from operation and will disconnect from power after 30 seconds of interruption. Please remove
obstacles before re-starting. To reset, simply turn off the power supply to the fan motor and re-start.
Over 80W protection: When the receiver detects power consumption which is greater than 80W, the receiver
power will be stopped and operation will immediately discontinue. Turn the receiver power on after 5 seconds to
restart the fan.
REPAIRING THE FAN RECEIVER & REMOTE PAIRING
Should the remote and receiver lose control after installation or during use, the pairing of the remote and the receiver
must be repaired. Below are the operating symptoms and method to repair the pairing of the DC ceiling fan remote and
receiver.
Issues:
Loss of control - Fan is only running at high speed after installation
Loss of control - No reverse function after installation
Loss of control - Remote cannot communicate with the receiver
Solution:
If the fan runs at the highest speed continuously, it means the wiring of the installation is correct. When the fan operates
on high speed only, or fails to operate in reverse function or any other command/s, it is recommended to repair the
communication pairing of the remote and receiver. Please follow the steps below:
A. Remove the battery cover on the remote. Make sure the battery is installed correctly and the red LED light
indicator will be flashing. This means the remote function is okay.

9 | P a g e
test
B. Turn off the main supply to the receiver for more than 30 seconds and turn on the main supply to receiver again.
Press and hold the SET button on the remote for 6 seconds within 60 seconds of turning the power on to the
receiver.
C. Press the buttons on the remote to run the fan. In general, performing point A, B, and C should repair the remote
and receiver and will allow full control of the fan. If not, please do the next step.
D. The DIP switches on the fans are set up at the factory. The DIP switch can be changed to any location in 16 options.
(Eg. up-up-down-down).

10 | P a g e
test
E. Please repeat the (A)-(C) steps to check the function.
If the issues still persist after following point (A) to (D) and there is still no control, then please contact the local retailer
for a new remote or transmitter.
NOTE: For your safety, a new receiver must be installed by a licensed electrician.
NOTE: While repairing the DC ceiling fan remote and receiver is in process, the fan operates at highest speed with
REVERSE mode automatically for 90 seconds, and then operates with FORWARD mode for 90 seconds. During the
paring process, do not press any key on the remote.
BALANCING / WOBBLING TROUBLESHOOTING
Please note that not all ceiling fans are the same, even in the same model—some may move more or less than others.
Movement of a couple of centimetres is quite acceptable and does not suggest that the fan will fall down.
Even though all blades are weighted and grouped by weight, it is impossible to eliminate wobble altogether. This should
not be considered a fault. Ceiling fans tend to move during operation due to the fact that they are not generally rigidly
mounted.
You may do the following action to reduce the wobbling:
1) Check all the blade mounting screws are tightened and securely.
2) Wobbling problems may result from inconsistent blade level. To check blade level, measure the distance from each
blade tip to the ceiling.
Note: If measurements are inconsistent:
- Check that the blade mount screws are not over tightened or loose, which can cause the blade tip to not sit
level;
- An out of shape blade can cause wobbling, check by removing the blade and lay it on a flat surface. A good flat
blade will lay flat on the surface.
3) Blade tracking may be checked simply by use of a household ruler as shown in the below figure. Place the ruler
vertically against the ceiling and even with
the outside leading edge of a blade. Note
the distance of the edge of a blade is the
same as the others. Turn the blade slowly
by hand to check the remaining blades. If a
blade is not in alignment, the blade is either
out of shape/warped or the blade screws
are not evenly tightened or loose.
BALANCING KIT Fig. 12
1. A balancing kit is provided to balance the ceiling fan on initial installation. Please refer to the instruction on how to
use the balancing kit, that is included.
2. The balancing kit can be used to assist re-balancing if the ceiling fan becomes un-balanced overtime. Do not
discard the balancing kit, retain for future use.

11 | P a g e
test
FAN CARE AND WARRANTY INFORMATION
Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid
scratching the paint/plated finish. Please make sure the fan is not operating when cleaning.
Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the
possibility of an electrical shock.
WARRANTY SERVICE
The manufacturer’s warranty covers actual faults that may develop, but NOT minor complaints, e.g. noise from motor
run—ALL ELECTRIC MOTORS AREAUDIBLE TO SOME EXTENT.
WOBBLE
Ceiling fans tend to move during operation due to the fact that they are not generally rigidly mounted—if they
were, they could generate excessive ceiling vibration and stress on their mountings.
Movement of a couple of centimetres is quite acceptable and does not suggest the fan will fall down.
Ceiling fans are mounted very securely on steel brackets with rubber cushioning or with ball-joints to allow free
movement.
Please note that not all ceiling fans are the same, even in the same model—some may move more or less than
others.
NORMAL WEAR AND TEAR
Threaded components working slightly loose or blade carriers even slightly bent due to vigorous cleaning or bumping
can cause extra wobble and noise. THIS IS NOT COVERED UNDER WARRANTY- but a little care and maintenance
can reduce or prevent this problem.
BUMP-IN-THE-NIGHT
This is outside the manufacturer ’s warranty. If a fan has a fault, it will be noticeable at all times. Naturally, when
everything is quiet at night, you will be more inclined to hear small noises which may not be noticeable at other times.
Even slight power fluctuations and mains frequency signals superimposed in your electricity supply may cause a
change in fan motor noise, this is normal.
FAN LIGHT
Except for actual faults in manufacture, which are extremely rare, FAN LIGHTS AND GLOBES ARE NOT COVERED
UNDER YOUR FAN WARRANTY. Noises and vibration etc. are often more accentuated when a fan light is fitted.
For instance a fan light glass that has not been tightened or worked loose can cause a rattle. Again, care and
maintenance will reduce this.

12 | P a g e
test
TROUBLESHOOTING CHECKLIST
Always check the “Troubleshooting Checklist”included in this booklet before calling for service.
For your safety, ensure the ceiling fan is OFF before carrying out any troubleshooting.
TROUBLE
PROBABLE CAUSES
SUGGESTED REMEDY
1. Fan will not start
(Warning: The
ceiling fan must be
switched OFF and
the assistance of a
licensed electrician
may be required.)
A. Fuse or circuit breaker blown.
Check main and branch circuit fuses or circuit
breakers.
B. Loose power connections to
the fan. (Normally occurs during
installation.)
Check power connection to the fan. This must
be performed be a licensed electrician.
C. No response from the remote
transmitter.
- Battery is low. Replace batteries.
- Check if correct remote transmitter is
paired with the receiver.
D. Switch the fan ON via the
mains switch.
Check if there is power to the fan.
2. Fan
Wobbles.
(Refer to Wobble
section of the
manual for further
information.)
A. Fan blades are not horizontal
to the ceiling.
Refer to “wobbling fixing” section of manual.
- The blade may require adjustment at the
blade mounting screws.
- The blade is out of shape, thus causing
wobbling. A new blade set will be required
to be replaced. Contact retailer for further
details.
B. Blade screws are loose.
Make sure all screws are securely fastened.
C. Blades are out of shape.
Remove blade and lay on a flat surface to check if
blades are out of shape. Contact retailer for further
details.
3. Fan sound is
noisy.
A. Top canopy is touching the
ceiling.
Lower canopy from ceiling to ensure minimum
1/10th in. clearance.
B. Loose fan blade screws.
Re-tighten all screws on the fan blades but
never over-tighten.
C. Ceiling fan not secured against
ceiling.
Re-tighten all screws in the hanging bracket or
plate.
D. Incorrect speed controller.
Change the controller to the one supplied.
(Must be performed by a licensed electrician.)
4. Mechanical
noise.
A. Allow at least for 8 hours
settling-in period.
5. Light will not
turn ON. (Optional
light kit ONLY.)
The globe/lamp has failed.
Replace globe/lamp.
WARNING: THE CEILING FAN MUST BE SWITCHED OFF BEFORE TROUBLE SHOOTING IS PERFORMED.
NOTES TO INSTALLERS
Some fans wobble more than others—even in the same model.
Fan lights can rattle but are not covered under warranty.
Fan wall controllers make a slight buzzing noise and get warm especially on a lower setting.
These occurrences are not covered by the manufacturer’s warranty.

13 | P a g e
test
TECHNICAL INFORMATION
DC FAN models
Rated Voltage
Rated power (motor)
Battery for remote
ICF72 –72 in. ceiling fan
110VAC
35W
1 x 12V 23AE
ICF96 –96 in. ceiling fan
110VAC
35W
1 x 12V 23AE
WARRANTY CONDITIONS
Ventamatic, Ltd. extends this warranty to the original retail purchaser of its model or, if this unit is purchased and installed by a
building contractor, then to the original owner of the home. No subsequent purchaser of the unit or of a home in which it is
installed is entitled to any of the benefits of this warranty.
This product is warranted against defects in materials and workmanship for a period of one (1) year from the date of original retail
purchase. No other parts or components are warranted. There is no warranty for defects caused by abuse, faulty installation, or
the like. Repairs or replacement parts supplied under this warranty are warranted only for the period of this warranty; that is, one
(1) year from the date of the original retail purchase of the unit.
In the event of a defect or malfunction, we will replace or repair the defective part or component only and return the new or
repaired part to you freight prepaid. You must bear all other expenses incurred in obtaining repairs, including labor required for
field repair or replacement, and the cost of shipping the defective part to us. You must also bear the cost of repair to or
replacement of any part or component and the shipping charges incurred for the repair or replacement and return to you of any
part or component not covered by this warranty, including parts or components damaged by you.
The company reserves the right to demand and receive written evidence of the date of purchase before undertaking to perform its
obligations under this warranty. You should, therefore, retain your sales slip and attach a copy of it to the warranty claim.
In order to obtain the repair or replacement of this unit, you must select one of the following methods:
A. Return to factory.
Return postage prepaid only the part or component which you believe to be defective to the following address:
Ventamatic, Ltd
100 Washington Street
Mineral Wells, TX 76067
Complete and enclose a written claim and attach a copy of your sales slip or other proof of purchase.
B. Return to place of purchase.
It is suggested that you first contact the dealer to ascertain if they will honor the warranty.
There is no informal dispute settling mechanism available in the event of a controversy involving this warranty.
Any and all implied warranties which may exist terminate upon the expiration of this warranty one (1) year from the date of the
original retail purchase. Some states do not allow limitations on how long an implied warranty lasts, so this limitation may not
apply to you.
Ventamatic, Ltd. is not liable to you for incidental or consequential damages arising out of a defect or malfunction of a unit or its
installation or out of any alleged breach of this warranty. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so this limitation may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.