Big Dipper K006RG SEVEN STARS User manual

SEVEN STARS
Big Dipper Laser Science And Technology Co., Ltd
REV: 1.01
LASERDISPLAYSYSTEM
USER MANUAL
Please read this manual carefully before operating
®
®

LASER DISPLAY SYSTEM USER MANUAL
Model：K006RG
Notices information
1. This is 3B laser product .Avoid eyes direct exposure to the
laser light.
2. Operate abide by the user manual .Do not disassemble or
repair the system by yourself. When there is a problem, please
contact technician, or your local dealer.
3. Installation should be done by professional technician.
4. Please set the laser product far away from those things as
strobe light.
5.The system should be kept dry .please don’t exposure the
system to wet or dust-laden environment need water proof
environment in the open air
6. Do not touch the system by wet hand or pull the power cable
forcefully.
7. The work temperature is 10-40℃,so the laser conduct doesn’t
work normally until it reach the work temperature when taking it in
from cold environment .
8. Do not turn on or off the system frequently, and avoid keep it
working for long time.
9. Prevent from strong vibration or G-shock to the system.
10. Prevent other harmful objects from entering the system.
11. Keep at least 1 meter between the system and the objects in
the lighting.
Page 1

12. Connect the power cable after the system has been
installed.
13. Before powering on the system, be sure the power cable is
connected into the power socket well.
14. Turn off the system for 25 minutes after running constantly
for three hours, ensure that the system is able to cool down in a
suitable environment.
15. Turn on the computer after the laser display system is on,
or you must power on the computer again.
16. When to be transported, use the original package to avoid
Shaking.
17. This sign indicates separate collection for electronics and
electrical equipment.
Inspection information
In order to use the product securely and properly, please read the
manual before using and follow the instructions strictly to prevent
personal safety trouble and product damage caused by misuse.
Take care of the product, check the possibility of the product
damage caused by transportation and check all the machine and
listed accessories are present upon receipt of the product.
1 x LASER display system 1 x User manual
1 x Power cable
Installation
1. Be sure that there is no flammable or explosive subjects nearby.
The least clear proximity from the system should be 1.5 meters. At
the same time, keep more than half a meter between the wall and
LASER display system.
Page 2
Remark: When Master-slave mode , any unit can be master.
When they aren’t synchronous , the slave will catch up with master ,
then to be synchronous .
2. When the 10th code is OFF: DMX control.
Maintenance
Clean the lens regularly. Do not use a wet cloth or chemicals; use a
damp cloth. The maintenance period depends of the usage
frequency and surrounding conditions of the LASER display system.
It recommended that the system should be cleaned every 15 days.
Warning
Power off any related system before maintenance.
Declare
The end-user of this product should abide by the above instructions
and warnings. Performing actions which was advised not to do so as
stated by this manual may void the warranty of this laser display
system.
All products made from Big Dipper Laser Company have anti - fake
identification. please verify the anti-counterfeit label at the bottom
of the case to ensure the interests of consumers.
Page 7

Remark
On the DMX 512 mode, the LASER display system will shut off if the
DMX 512 signal intermit.
ADDRESS SETTING:
DMX address setup
1. When the 10th code is ON, the function of 1-9 codes is the
following
The 1st code is OFF------Sound control mode (host LASER)
The 1st code is ON------AUTO play mode (host LASER)
The 2nd code is ON------ (passivity LASER)
Page 6
2. Be sure the power socket output voltage matches that off the
LASER display system.
3. Ensure the fan and the exhaust is not blocked.
4. The LASER display system should be statically fixed.
5. It is essential to be earthed well for the sake of safety.
Back panel
Key-press function instruction
1. Fan
2. DMX512 signal output socket
3. DMX512 signal input socket
4. Binary address switch
5. Power socket
6. Power switch
Page 3
218-255 Anticlockwise rotate (automatic)
10 Displa y
mode
0-63 Normal display
64-127 Dot and line display
128-191 Subsection display
192-255 Dot Display
11 Wave
0-10 No wave
11-200 Wave frequency from low to high
201-255 Frequency and fixed extent from low
to high
12 color
0-31 Yellow
（
Red Green
）
32-63 Green
64-95 Red
96-127 Break off color separation（
red and
green 2 colors）
128-159 8 dots color separation（red, green and
yellow 3 colors
）
160-191 16 dots color separation（red, green
and yellow 3 colors）
192-223 Red, green, yellow 3 color flows
224-255 Change color by sound
13 Gradu ally-dr
aw
0-1 No gradually draw
2-150 Manual gradually draw
151-250 Gradually draw circularly
251-255 Sound control gradually draw

Technical Parameters
Model
Parameters K006RG
1 LASER diode Red/green
2
Power supply
AC100-240V, 50/60HZ
3 LASER power R >100Mw G>60mW
4
Scanner angle
±15°
5
Control mode
Sound/Auto-play/
Single pattern by DMX/Master-slave
6 DMX 13
7 Effect 3D laser with high speed scanner can
display hundreds of beam and
graphics with move, strobe, rotate,
zoom, gradually draw etc.
tridimensional effects.
8
Dimensions 214*160*135MM
9
Net weight/
Gross weight 1.35/1.4KGS
Page 4
DMX channel setting
Channel No. DMX512
value Content
1 Control
mode
0-63 Shut off the LASER diode
64-127 Sound mode
128-191 AUTO mode
192-255 Manual mode
2 Pattern
0-167
Static pattern
168-255 Dynamic patterns
3 Strobe 0-255 8 grade speed (0~255)/30=(0~8)
4 Horizontal
move
0-167 Manual move
168-188 Automatic move circularly from left to right (have spring function)
189-209 Automatic move circularly from right to left (have spring function)
210-255 Automatic move around circularly
5 Vertical
move
0-167 Manual move
168-188 Automatic move circularly from up to down(have spring function)
189-209
Automatic move circularly from
down to up(have spring function)
210-255 Automatic fluctuate circularly (from up to down and down to up)
6 Zoom
0-10 No zoom
11-104 Manual zoom
105-154 Automatic zoom out
155-204 Automatic zoom in
205-255 Automatic zoom circularly
7 Horizontal
stretch
0 No stretch
1-150 Manual stretch
151-255 Automatic stretch
8 Vertical
stretch
0 No stretch
1-150 Manual stretch
151-255 Automatic stretch
9 Rotation 0 No rotate 1-180 Manual Rotate
181-217 Clockwise rotate (automatic)
Page 5