Big Lots GRAND CHERRY FP-1829 Mounting instructions

ASSEMBLY INSTRUCTION SHEET
ITEM# FP-1829
SKU# 810385720
DESCRIPTION: GRAND CHERRY FIREPLACE
CUSTOMER SERVICE NO.:
1-888-878-8820
Email:[email protected]

A
C
PARTS LIST
TOP 1pc
F
D
BASE 1pc
ELECTRIC FIREPLACE
INSERT 1pc
B
GH I
J L
FRONT PANEL 1pc
TOP RAIL 1pc SIDE RAIL 2pcs
LEFT SUPPORT
1pc
RIGHT SUPPORT
1pc
K
LEFT SIDE PANEL
1pc
RIGHT SIDE PANEL
1pc
SIDE TRIM 2pcs
E
POST 2pcs
Warning:
1. Need at least two adults to assemble this fireplace.
2. Assemble on soft , smooth surface to protect finish from being
scratched .
3. DO NOT use power tools.
4. Remove all packaging material, make sure all parts are present
before assembly.
5. Estimated Assembly Time: 30 minutes. Exact assembly times
will vary based on skill level and past assembly experience.
Customer Service
For the missing or replacement of wooden panels, hardware, or
electric fireplace insert, please contact Vendor Customer Service at
1-888-878-8820
Working hour: Mon.-Fri., 8:30am - 5:30pm Pacific Standard Time.
CARE INSTRUCTIONS:
1. Clean periodically by wiping the product with a soft clean cloth.
2. Do not expose your product to any liquids. All liquids should be
wiped up immediately with a soft, slightly damp cloth in the
direction of wood grain.
3. Do not expose your product to strong or direct sunlight, near heat
outlets or air conditioning units, open windows or dampness.
Excessive exposure to sunlight and heat can cause fading of your
furniture finish. Extreme temperatures and humidity changes can
cause wood cracking and splitting.
4. Clean using a glass/mirror cleaner and soft cloth. Do not use
cleaning products containing abrasives, as these will scratch
glass/mirror.
!

ASSEMBLY INSTRUCTION
H1
H2
H4
H5
72 pcs
1 pc
ALLEN WRENCH
FLAT WASHER
4 MM
∅1/4"*16MM
SPRING WASHER ∅1/4"
LONG BOLT ∅1/4*1-1/4" 12 pcs
72 pcs
Figure 1
H6 6 pcs
#8*12MM
Step 1
Place Left side panel (D) face down on a smooth soft surface. (The side
with the most holes should be facing up.) Align the holes of Bracket
(H8) with the holes of Left side panel (D) with the tenons facing
outward as shown in figure 1. Secure the Bracket (H8) to the Left side
panel (D) with Flat washer (H4), Spring washer (H3), and Short bolt
(H2) using Allen wrench (H5). DO NOT fully tighten bolts in this step
for later adjustment. Repeat this procedure to attach Bracket (H8) to
Right side panel (E) and Front panel (C) as shown in figure 1.
PARTS LIST
H7
H3
SHORT BOLT ∅1/4*5/8" 60 pcs
20 pcs
H8
ROUND HEAD SCREW
BRACKET
D
D
Tenons facing outside.
H2
H3
H4
H5
10 pcs
H8
C
H8
H8
BRACKET

ASSEMBLY INSTRUCTIONASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION
Step 2
With assistance from another adult, place Left side panel (D) onto its side.
Insert the tenons of Side trim (F) into the corresponding holes of Left side
panel (D). Secure Side trim to Left side panel (D) with Long bolt (H1),
Spring washer (H3) and Flat washer (H4) using Allen wrench (H5) as
shown in figure 2. DO NOT fully tighten bolts in this step for later
adjustment. Repeat process to attach remaining Side trim (F) to Right side
panel (E).
D
F
H3
H4
H1
H5 B
D
E
B
D
H2
H3
H4
H5
Figure 2 Figure 3
Step 3
With assistance from another adult, insert the tenons of Left side panel
(D) into the corresponding holes of Base (B). Secure Left Side panel (D)
to Base (B) with Short bolt (H2), Spring washer (H3), Flat washer (H4)
using Allen wrench (H5) as shown in figure 3. DO NOT fully tighten
bolts in this step for later adjustment. NOTE: The Left side panel (D)
should be supported until secured in place to prevent the panels from
tipping and causing damage or injury. Repeat this process for the Right
side panel (E).
Trim on the side panel
should be on top.
Trim on the side panel
should be on top.

ASSEMBLY INSTRUCTIONASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION
Figure 4
Step 4
With assistance from another adult, insert the tenon of Post (G) into the
corresponding hole of Base (B). The trim on Post (G) should align with the
Side trim (F) on the Left side panel (D). Secure the Post (G) to the Left side
panel (D) using Bracket (H7), Flat washer (H4), Spring washer (H3) and
Short bolt (H2) using Allen wrench (H5) as shown in figure 4. DO NOT
fully tighten bolts for later adjustment. NOTE: Post (G) should be supported
until secured in place to prevent the posts from tipping and causing damage
or injury. Repeat this process to attach the remaining Post (G) to the Right
side panel (E).
Figure 5
Step 5
Align the holes of Left support (H) with the holes in Post (G). NOTE:
The tenons on Left support (H) should be facing up. Secure Left
support (H) to Post (G) with Bracket (H7), Flat washer (H4), Spring
washer (H3) and Short bolt (H2) using Allen wrench (H5) as shown in
figure 5. DO NOT fully tighten bolts for later adjustment. Repeat the
process to attach the Right support (I) to remaining Post (G).
Trim on the side panel
should be on top.
B
D
E
G
G
GD
H2
H3
H4
H5
B
H
I
D
G
G
E
H
G
H2
H3
H4
H5
H7
H7

ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION
Step 6
Align the tenons of the Left support (H) and Right support (I) with the
holes in Front panel (C). The parts may need to be slightly adjusted for
Front panel (C) to fit properly. Secure Front panel (C) to Posts (G) with
Bracket (H7), Flat washer (H4), Spring washer (H3) and Short bolt
(H2) using Allen wrench (H5) as shown in figure 6. DO NOT fully
tighten bolts for later adjustment.
Figure 6 Figure 7
Step 7
With assistance from another adult, insert the tenons of Side rail (K) into
the corresponding holes of Base (B) with the glossy side facing the front
of the mantel. The holes in Left support (H) should align with the holes in
Side rail (K). Secure Side rail (K) to Left support (H) with Flat washer
(H4), Spring washer (H3) and Short bolt (H2) using Allen wrench (H5) as
shown in figure 7. DO NOT fully tighten bolts for later adjustment. Use
the same process to attach remaining Side rail (K) to Right support (I).
H2
H3
H4
H5
H7
C
C
H
I
G
G
B
B
C
C
K
H
I
B
K
K
H
I
K
H
H3
H4
H5
H1
G
H
I
C

ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION
Figure 8
Step 8
With assistance from another adult, place Top rail (J) onto the tenons of
Side rail (K) with the glossy side facing the front of the Mantel. The
Side rails may need to be slightly adjusted for the Top rail (J) to fit
properly. Align the holes of Top rail (J) with the holes of Left support
(H) and Right support (I). Secure the Top rail (J) to Left support (H),
Front panel (C) and Right support (I) with Flat washer (H4), Spring
washer (H3) and Long bolt (H1) using Allen wrench (H5) as shown in
figure 8. DO NOT fully tighten bolts for later adjustment.
Figure 9
Step 9
With assistance from another adult, align the tenons of the Left side panel (D),
Post (G), Front panel (C), Post (G) and Right side panel (E) with the
corresponding holes in Top (A). Be careful not to pinch you fingers when
lowering Top (A) into position. Several parts may need to be moved slightly to
allow Top (A) to fit properly. Attach Top (A) to Left side panel (D), Front
panel (C) and Right side panel (E) using Flat washer (H4), Spring washer (H3)
and Short bolt (H2) using Allen wrench (H5) as shown in figure 9. Adjust all
remaining parts to minimize any gaps and tighten all bolts from steps 1-9.
H2
H3
H4
H5
Make the Left and Right
support(H & I) tightly
close to the center.
D
A
C
G
D
H
C
I
H
I
C
C
A
K
K
J
C
B
B
K
K
J
C
H
I
H3
H4
H5
H1
J
K
H
C
B
C
A
E
G
G

Assembly is now complete.
Note: Please read the operating manual for the Electric Fireplace Insert and
Electric Fireplace Insert remote control before using Fireplace.
MADE IN CHINA
ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION
Step 10
Place the Electric fireplace insert (L) into the assembled Mantel from
the back. Slide the Electric fireplace insert (L) into the opening of the
assembled Mantel and center so the space around the insert and rails is
equal. Secure the Electric fireplace insert to the back of the assembled
Mantel with Round head screws (H7) using Phillips screwdriver (not
provided) as shown in figure 10.
Figure 10 PRINTED IN CHINA
L
Not provided
L
H6
K
K
K