Big Lots HF170192 User manual

Item No. : HF170192
Page 1 of 10
SKU No. : 810392478
Description: 48IN CHERRY CORNER FIREPLACE
Assembly Instruction
Option A Option B
Clean with a dry soft rag.
To prevent serious injury or death, this product is equipped with a wall anchoring
system. Before this product can be used, the wall anchoring system must be
installed as directed in the assembly instructions.
For spare parts, please contact Homestar Customer Care
E-Mail: [email protected]Tel: [phone]

Page 2 of 10
Screwdriver Allen Key
16pcs
(Not included) (Included)
Tools Required Box
A
16pcs
B
16pcs
C
9pcs
D
8pcs
E
2pcs
F
1
4
5
6
7
8
2
3

Page 3 of 10
STEP1
STEP2
1
3
2
C
E
x4
x4
B
A
1
4
Attach side panels (part 2) and
(part 3) to base panel (part 1)
using bolts (part A), spring
washer (part B) and flat washer
(part C) by Allen Key as shown
in the diagram.
Slide the front panel as
shown in the diagram.
Insert the wood dowel (part E)
to the ouside hole of base panel
(part 1) first.
Fully tighten all bolts in this step.

STEP4
Page 4 of 10
STEP3
C
C
E
E
EE
B A
x6
x4
4
5
B
A
Attach front panel (part 4) to side
panels (part 2) and (part 3) using
bolts (part A), spring washer
(part B) and flat washer (part C)
by Allen Key as shown in the
diagram.
2
3
Attach top panel (part 5) to
side panels (part 2) and
(part 3) using bolts (part A),
spring washer (part B) and
flat washer (part C) by Allen
Key as shown in the diagram.
2
3
Fully tighten all bolts in this step.
Fully tighten all bolts in this
step.
Insert the wood dowel (part E)
to the ouside hole of side panel
(part 2) and (part 3) first.

Page 5 of 10
STEP6-A
STEP5
x1
66
C
B
A
Attach support foot (part 6) to base
panel (part 1) using bolts (part A),
spring washer (part B) and flat
washer (part C) by Allen Key as
shown in the diagram.
Option A: Using on flat wall
1
Fully tighten all bolts in this step.
U
U
T
Z
Z
Z
ZZ
Z
Z
Please refer to Insert manual to assembly
the insert trims first as below on page E-3.

Page 6 of 10
STEP7-A
Please make sure the insert trims
have been assembly first.
Then carefully slide the firebox into
the completed Mantel and center
in the opening.

Page 7 of 10
STEP8-A
INSTALLATION INSTRUCTIONS:
F
F
Z
Z
Z
Securing the firebox to the mantel by
using six Screws (Z) as insert manual.
This Tip Restraint should be attached to a wall stud where possible. If Placement does not align
with a wall stud, the plastic wall anchor must be used.
1. Using the 5/8” screw provided, attach the bracket to the top wood panel of the mantel inserting
the screw through the smaller hole in the bracket. Fully tighten the screw.
2. Place the fireplace mantel in the desired location and mark the location of the installed bracket
on the wall. Remove the mantel.
3. Locate a spot about 2” below the mark made for the first bracket. Secure the second bracket to
the wall with the 2” screw provided. If the screw hits a wall stud then fully tighten the screw and
the plastic anchor does not need to be used. If no wall stud is located, remove the screw and
insert the plastic wall anchor. Attach the bracket to the plastic wall anchor and fully tighten the
screw.
4. Replace the mantel back into the desired location. The brackets should be aligned vertically.
5. Lace the end of the restraint strap trough the larger hole in each bracket. Bring the ends of the
strap together and slide the flat end of the restraint strap through the locking end and draw it
through until all slack is removed.
6. Confirm the strap is securely laced and locked.

Page 8 of 10
x1
C
B
A
STEP6-B
STEP7-B
7
Option B: Using on corner wall
Please make sure the insert trims
have been assembly first.
Then carefully slide the firebox into
the completed Mantel and center
in the opening.
Attach support panel (part 7) to base
panel (part 1) using bolts (part A),
spring washer (part B) and flat
washer (part C) by Allen Key as
shown in the diagram.
Fully tighten all bolts in this step.
For corner using, please do not
assemble the support foot (part 6).
And take care to keep the support
foot for future flat wall use.
Z
Securing the firebox to the mantel by
using six screws (Z) as insert manual.

Page 9 of 10
x3
x1
C
B
A
D
STEP8-B
STEP9-B
8
8
7
Attach support panel (part 7)
to top triangle panel (part 8)
using bolts (part A), spring
washer (part B) and flat
washer (part C) by Allen Key
as shown in the diagram.
Attach top panel (part 5)
to top triangle panel (part 8)
using screw (part D) by
screwdriver as shown in
the diagram.
Fully tighten all bolts in this step.

Page 10 of 10
STEP10-B
8
INSTALLATION INSTRUCTIONS:
F
F
F
F
This Tip Restraint should be attached to a wall stud where possible. If Placement does not align
with a wall stud, the plastic wall anchor must be used.
1. Using the 5/8” screw provided, attach the bracket to the top wood panel of the mantel inserting
the screw through the smaller hole in the bracket. Fully tighten the screw.
2. Place the fireplace mantel in the desired location and mark the location of the installed bracket
on the wall. Remove the mantel.
3. Locate a spot about 2” below the mark made for the first bracket. Secure the second bracket to
the wall with the 2” screw provided. If the screw hits a wall stud then fully tighten the screw and
the plastic anchor does not need to be used. If no wall stud is located, remove the screw and
insert the plastic wall anchor. Attach the bracket to the plastic wall anchor and fully tighten the
screw.
4. Replace the mantel back into the desired location. The brackets should be aligned vertically.
5. Lace the end of the restraint strap trough the larger hole in each bracket. Bring the ends of the
strap together and slide the flat end of the restraint strap through the locking end and draw it
through until all slack is removed.
6. Confirm the strap is securely laced and locked.