Bihui BLFVTB User manual

1
BLFVTB Original instructions
Read before use

2
Read the manual
Danger: Risk of injury and equipment damage.
General safety instructions for power tools
WARNING Read all safety instructions, instructions, illustrations and technical data
provided with this power tool. Failure to follow the instructions below may result in electric
shock, fire and / or serious injury.
Keep all safety and instructions for the future.
The term "power tool" used in the safety instructions refers to mains operated power tools (with
power cord) or to battery operated power tools (without power cord).
1) job security
a) Keep your work area clean and well lit. Disarray or unlit work areas can lead to accidents.
b) Do not work with the power tool in a potentially explosive environment in which
flammable liquids, gases or dusts are present. Power tools generate sparks that can ignite
the dust or vapors.
c) Keep children and other persons away while using the power tool. With distraction, you can
lose control of the power tool.
2) Electrical safety
a) The plug of the power tool must fit into the socket. The plug must not be changed in any
way. Do not use adapter plugs together with electrically grounded power tools.
Unmodified plugs and matching sockets reduce the risk of electric shock.
b) Avoid body contact with grounded surfaces such as pipes, heaters, stoves, and
refrigerators. There is an increased risk of electric shock if your body is grounded.
c) Keep power tools away from rain or moisture. The penetration of water into a power tool
increases the risk of electric shock.
d) Do not misuse the power cord to carry the power tool, hang it up, or unplug it from the
power outlet. Keep the connection cable away from heat, oil, sharp edges or moving
parts. Damaged or entangled leads increase the risk of electric shock.
Symbols
The following are the icons that are used for the tool. Make sure you fully understand them before
using them.

3
b) Wear personal protective equipment and always safety goggles. Wearing personal
protective equipment such as a dust mask, non-slip safety shoes, hard hat or ear protection,
depending on the type and use of the power tool, reduces the risk of personal injury.
c) Avoid unintentional startup. Make sure that the power tool is switched off before
connecting, receiving or carrying it to the power supply and / or the battery. Keeping
your finger on the switch when you are wearing the power tool or plugging the power tool into
power can cause an accident.
d) Remove setting tools or wrenches before turning on the power tool. A tool or key located in
a rotating part of the power tool can cause injury.
e) Avoid an abnormal posture. Ensure a secure footing and maintain balance at all times.
This allows you to better control the power tool in unexpected situations.
f) Wear suitable clothing. Do not wear loose clothing or jewelry. Keep hair and clothing away
from moving parts. Loose clothing, jewelry or long hair can be caught by moving parts.
g) If dust extraction and collection equipment can be installed, they must be connected and
used properly. Using a dust extractor can reduce dust hazards.
h) Do not weigh yourself in false safety and do not overstep the safety rules for power tools,
even if you are familiar with the power tool after many uses. Careless action can lead to
serious injuries within fractions of a second.
4) Use and treatment of the power tool
a) Do not overload the power tool. Use the appropriate power tool for your work. With the
right power tool you work better and safer in the specified power range.
b) Do not use a power tool whose switch is defective. A power tool that can not be turned on or
off is dangerous and must be repaired.
c) Unplug the power cord and / or remove a detachable battery before making any
adjustments to the device, changing the tool bits, or putting the power tool away. This
precaution prevents the unintentional start of the power tool.
d) Store unused power tools out of the reach of children. Do not allow persons to use the
power tool that are unfamiliar or have not read these instructions. Power tools are
dangerous when used by inexperienced people.
e) Maintain power tools and insert tools with care. Check that moving parts are working
properly and do not jam, that parts are broken or damaged enough to impair the
functioning of the power tool. Have damaged parts repaired before using the power
tool. Many accidents are caused by badly maintained power tools.
suitable for outdoor use. Using an extension cord suitable for outdoor use reduces the risk
of electric shock.
f) If operation of the power tool in a damp environment is unavoidable, use a residual
current device. Using a residual current circuit breaker reduces the risk of electric shock
3) safety of persons
a) Be attentive, pay attention to what you are doing and be reasonable about working with a
power tool. Do not use a power tool when you are tired or under the influence of drugs,
alcohol or medication. A moment of carelessness when using the power tool can cause
serious injury.
e) When working outdoors with a power tool, only use extension cables that are also

4
c) Keep the unused battery away from paper clips, coins, keys, nails, screws, or other small
metal objects that could cause the contacts to bridge. A short circuit between the battery
contacts can cause burns or fire.
d) If used incorrectly, liquid may leak from the battery. Avoid contact with it. In case of
accidental contact, rinse with water. If the fluid gets into your eyes, seek additional
medical attention. Leaking battery fluid may cause skin irritation or burns.
e) Do not use a damaged or modified battery. Damaged or altered batteries can behave
unpredictably and cause fire, explosion or injury.
f) Do not expose a battery to fire or high temperatures. Fire or temperatures over 130 ° C can
cause an explosion.
g) Follow all charging instructions and never charge the battery or the cordless tool outside
the temperature range specified in the operating instructions. Incorrect charging or
charging outside the permitted temperature range can destroy the battery and increase the
risk of fire.
6) service
a) Only have your power tool repaired by qualified personnel and only with original spare
parts. This ensures that the safety of the power tool is maintained.
b) Never wait for damaged batteries. All battery maintenance should only be done by the
manufacturer or authorized service centers.
Follow the instructions for lubricating and changing accessories.
3
h) Keep handles and grips dry, clean and free of oil and grease. Slippery handles and gripping
surfaces do not allow safe operation and control of the power tool in unforeseen situations.
5) Use and treatment of the cordless tool
a) Charge the batteries only with chargers recommended by the manufacturer. A charger
suitable for a particular type of battery may cause a fire when used with other batteries.
b) Use only the appropriate batteries in the power tools. Use of other batteries may cause
injury or fire.
h) Keep handles and grips dry, clean and free of oil and grease. Slippery handles and gripping
surfaces do not allow safe operation and control of the power tool in unforeseen situations.
5) Use and treatment of the cordless tool
a) Charge the batteries only with chargers recommended by the manufacturer. A charger
suitable for a particular type of battery may cause a fire when used with other batteries.
b) Use only the appropriate batteries in the power tools. Use of other batteries may cause
injury or fire.
f) Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges
become less jammed and easier to guide.
g) Use power tools, accessories, tools etc. according to these instructions. Take into
account the working conditions and the activity to be performed. The use of power tools
for other than intended applications can lead to dangerous situations.

5
Instructions for use of Vacuum lifter
1. Always make sure that you have a firm footing. Make sure that there are no people under the unit
when using the unit in a high location.
2. Do not carry heavy objects weighing more than 30 kg.
3. Keep the working surface of the object to be transported flat and free of debris on the surface to
ensure good sealing performance during machine operation.
4. The battery is sufficiently charged to ensure that operation is not interrupted due to insufficient
power.
5. Make sure that the goods can be brought to their destination in a good environment and are not
damaged by environmental damage.
KEEP INSTRUCTIONS
WARNING: Do not follow the relevant product safety rules to familiarize yourself with the
product (experience with repeated use). Do not follow the relevant product safety rules to
familiarize yourself with the product (experience with repeated use).
Improper use or failure to observe the safety instructions in the manual may result in serious injury.

6
IMPORTANT SAFETY INSTRUCTIONS FOR THE BATTERY CASSETTE
Before using the battery, read all instructions and warnings on the charger, the battery, and the
product that uses the battery.
-Do not disassemble the battery.
-If the operating time has become too short, stop operation immediately. There is a risk of
overheating, burns and even explosion.
-If electrolyte gets in your eyes, rinse with clean water and seek medical attention immediately. This
can lead to vision loss.
- Do not short the batteries:
(1) Do not touch the terminals with conductive material.
(2) Do not store the battery in a container with other metal objects such as nails, coins, etc.
(3) Do not expose the battery to water or rain.
A battery short circuit can cause a strong current flow, overheating, possible burns and even a
malfunction
-Do not store the device and the battery in places where the temperature can reach or exceed 50 °
C.
- Do not burn the battery even if it is badly damaged or worn out completely. The battery can
explode in case of fire.
- Be careful not to drop or hit the battery.
-Do not use damaged batteries.
- The battery is subject to the dangerous goods laws. Any transfer by a third party or carrier should
strictly adhere to the packaging and label requirements. Please read the detailed rules for the local
market and pay attention to them. Please protect it with a knock and fix the battery firmly to avoid
movement of the packaging.
- Always follow the local laws for the disposal of used batteries.
- Make sure that the battery is used for a particular tool. Improper or misuse may result in fire,
overheating, explosion or electrolyte leakage.

7
Tips for getting the maximum battery life
- Charge the battery cartridge before you have completely discharged it. Stop working and charge
the battery if you notice less tool power.
- Never charge a fully charged battery cartridge. By overcharging the charge shortens battery life.
-Charge the battery with the room temperature at 10 ° C - 40 ° C. Leave a hot battery cool before
loading.
- Use the battery pack under the ambient conditions of 10 ° C -40 ° C.
- Charge the battery every six months if you do not use it for a long time.
Application
The device is suitable for handling wood, metal, glass, plastic, stone and other materials The
adsorption surface of the object to be transported must be level, free of foreign bodies and of a
certain smoothness.
ATTENTION : Please use only the right battery / charger as above. Any use of improper
batteries / chargers may cause injury or even fire.
KEEP INSTRUCTIONS
ATTENTION: Please only use the original battery. Any use of a non-original or new battery
can cause an explosion, even possible fire, personal injury, or property damage.

8
zV
Operating Instructions
AB
C
D E

9
Operating Instructions
7
8
10
9

10
2
3
2
WARRANTY
2 (TWO) years from date of sale (delivery note/receipt or in-
voice). Any malfunctions caused by inappropriate or incorrect
use of the machine will not be covered under the warranty.
Descriptions and illustrations are purely indicative. Without prejudice to the essential features
of the models described and illustrated herein, the Company reserves all rights at any time, and
without notice, to make product changes considered necessary for improvement or required
in the interest of product engineering and sale. Without the previous authorisation of
Genesis Global Systems, the partial or total reproduction of this manual, in any format or
by any means or process, is strictly prohibited,whether such reproduction be mechanical,
photographic or electronic.
Any of these activities will incur legal liability and may give rise to penal action being taken.
DECLARATION OF COMPLIANCE WITH EEC REGULATIONS
We declare under our responsibility that the machine de-
scribed in these instructions is in accordance with the di-
rectives: EN 55014-1:2017 · EN 55014-2:2015 · EN 61000-3-
2:2014 · EN 61000-3-3:2013 · EN 60745-1: 2009 + A11.
DISPOSAL OF WASTE EQUIPMENT BY USERS IN PRIVATE
HOUSEHOLDS IN THE EUROPEAN UNION
This symbol on the product or on its packaging in-
dicates that this product must not be disposed of
with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment
by handing it over to a designated collection point
for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that pro-
tects human health and the environment. For more information
about where you can drop off your waste equipment for recy-
cling, please contact your local city ofce, your household waste
disposal service or the shop where you purchased the product.
BLFVTB can be used for indoor and outdoor installation. It
replaces the traditional manual operation and helps to avoid
problems due to the incorrect distribution of the adhesive under
tiles and big slabs. The main features are: extreme
usefullness, safety, respect for the environment and easy use.
1- Suction Pad
2 - Sub-Handle
3 - Lithium Battery
4 - ON / OFF main switch
5 - Suction Pad
6 - ON / OFF vibration
TECHNICAL DATA
Battery Capacity: 16V LI-ion - 2,0 AH – 32 WH
Charging current: 1 A
Charging time: 2,5 H
Vibration frequency: 5000 ÷ 12000 rpm
Suction power: 25 kg
NOTE
• The machine must be stored in a dry place.
• Remove any dirt or dust from the machine after use.
• Store BLFVTB in its carry-case to avoid damage.
• It’s recommended to recharge the BLFVTB daily, for
frequent use. It is also suggested to recharge it, at least, once
a month if not used for long periods.
INSTRUCTIONS
A) Assembly the battery pack
B) Hold down the on/off button to switch ON the machine.
C)
Press shortly the on/off button to adjust vibration:
- level 1: Red (Min.)
- level 2: Red and Yellow (Med.)
- level 3: Red, Yellow and Green (Max.)
D)
At level 3, hold down on/off button to switch OFF the machine.
E) Red light on/off ashing, means battery is at low level, re-
charge the battery.
IMPORTANT NOTICE: THIS BATTERY PACK IS NOT WATER
PROOF. MALFUNCTION CAUSED BY USE WITH WATER, IT’S
OUT OF WARRANTY.
OPERATING PROCESS
•Place the machine on the tile surface, lock the suction lever
forwards, (see Pic 7), lift the tile and move it to the working
area. (see Pic 8).
•Suction lever forwards, turn “BLFVTB” in “Suction mode”
with this set up , the tiler can lift the tile and once it has been
layed, vibrate it (see Pic 9).
•Suction lever backwards (see Pic 7), turn “BLFVTB” in
“hammer working mode” with this set up, the tiler can vi-
brate the tile, sliding the machine on it.
• When the tile/slab is placed in position turn the
“BLFVTB” on and slide it over the surface of the slab
using a “rotatory movement” to facilitate the outflow of
the air un-der the tile in order to obtain the correct
distribution of the adhesive (see Pic 10).
Application


For the Perfect Finish

PROFESSIONAL TILING TOOLS