Miller M-15 User manual

OWNER’S MANUAL
1996 MILLER Electric Mfg. Co.
October 1996 FORM: OM-180 516A
Use above FORM number when ordering extra manuals.
M-15, M-25, M-40, And M-40AL Guns (Euro-Connector)
1. Specifications
Air-CooledGuns For GMAW And FCAW Welding
M-15 Rated At 150 Amperes Using CO2Shielding Gas. Feeds .023 To .035 in (0.6 To 0.9 mm) Hard Or
Flux Cored Wires.
M-25Rated At 200 Amperes Using CO
2
Shielding Gas. Feeds .030 To .045 (0.8 To 1.1 mm) Hard Or Flu
x
M-25Rated At 200 Amperes Using CO2Shielding Gas. Feeds .030 To .045 (0.8 To 1.1 mm) Hard Or Flux
Cored Wires (Also Feeds .023 in (0.6 mm) Wire – See Parts List)
M-40 Rated At 400 Amperes Using CO2Shielding Gas. Feeds .035 To 5/64 in (0.9 To 2.0 mm) Hard Or
Flux Cored Wires.
ST-801 727 M-40ALRated At 275 Amperes Using Mixed Shielding Gas; Feeds .047 in (1.2 mm) Aluminium Wire
2. Safety Precautions For GMAW Guns
A. Symbol Usage
Means Warning! Watch Out! There are possible hazards with this
procedure!The possible hazards are shown in the adjoining symbols.
This group of symbols means Warning! Watch Out! Possible ELECTRIC SHOCK and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions to avoid the hazards.
YMarks a special safety message.
.Means NOTE; not safety related.
B. GMAW Gun Hazards
WARNING
The symbols shown below are used throughout this manual to call attention to and identify possible
hazards. When you see the symbol, watch out, and follow the related instructions to avoid the hazard. The
safety information given below is only a summary of the more complete safety information found in wire
feeder and welding power source manuals. Read and follow all Safety Standards.
ELECTRIC SHOCK can kill.
1. Always wear dry insulating gloves.
2. Insulate yourself from work and ground.
3. Do not touch live electrode or electrical parts.
4. Repair or replace worn, damaged, or cracked gun
or cable insulation.
5. Turn off welding power source before changing
contact tip or gun parts.
6. Keep all covers and handle securely in place.
HOT SURFACES can burn skin.
1. Allow gun to cool before touching.
2. Do not touch hot metal.
3. Protect others from contact with hot metal.
FLYING PIECES OF METAL or DIRT can
injure eyes.
1. Wear safety glasses with side shields or face
shield.
WELDING WIRE can cause puncture
wounds.
1. Keep hands and body away from gun tip when
triggeris pressed.
OVERUSE can damage gun and void
warranty.
1. Followrated duty cycle.
2. Allow cooling period.
3. Reduce current or reduce duty cycle before
startingto weld again.
1. Read and follow these instructions and all safety
blocks carefully.
2. Have only trained and qualified persons install
,
operate,or service this unit.
3. Call your distributor if you do not understand the
directions.
4. For WELDING SAFETY and EMF information
,
read wire feeder and welding power source
manuals.

OM-180 516 Page 2
3. Installing Gun
Ref. ST-801 728
1 Gun Securing Collar
2 Gun End
Insert gun end into receptacle and
tightencollar.
See wire feeder manual for thread-
ing procedure.
1
2
Duty Cycle is percentage of 10 minutes that gun
can weld at rated load without overheating.
Definition
6 Minutes WeldingContinuous Welding 4 Minutes Resting
4. Duty Cycle
Model Duty
Cycle At Amperes Shielding Gas
M-15
M-25 100%
150
120
200
CO2
Mixed Gases
CO2
Model Duty
Cycle At Amperes Shielding Gas
M-15
M-25 60%
200
150
300
CO2
Mixed Gases
CO2
Minutes
0
10
M-40 400 CO2525 CO2
275 Mixed Gases 400 Mixed Gases
M-40AL
M-40
M-40AL

OM-180 516 Page 3
5. Removing Nozzle, Contact Tip, And Adapter, Changing Liner, And Cleaning Gun
Casing
Ref. ST-801 729
YDisconnectgun first.
1 Nozzle
2 Contact Tip
3 Adapter
.Check to make sure wire size
stamped on contact tip
matches actual wire size.
Head
Tube
Lay gun cable out
straightbefore installing
new liner.
Remove nozzle,
contact tip, adapter,
and wire outlet guide.
Remove
liner.
Blow out
gun casing.
3/8 in
3/4 in
(20 mm)
Liner
Stickout Install
Liner
.Thread wire according to
weldingpower source/wire
feeder manual.
Reassemble gun in
reverse order from
taking it apart.
123
3/8 in (7/16 in for M-25)

OM-180 516 Page 4
6. Replacing Switch And/Or Head Tube (M-15 And M-25)
Ref. ST-800 795-A
3/4 in
Do not disturb cable connection between
cable connector and connector nut.
Remove handle lock-
ing nut. Slide handle.
Secure head
tube in vice. Remove shock washers from front and rear of
headtube.
Loosen jam nut.
Remove from vice
and turn head tube
out by hand.
Install both existing shock washers onto
new head tube, and hand-tighten head
tube into cable connector.
Place head tube in vice and tighten until
nuts are tight.
Remove from vice. Reposition handle and install
switch housing. Secure with handle locking nut.
YDisconnect gun first.
Removeswitch housing. Install new switch and
connect leads (polarity is not important). Reas-
semble in reverse order. If replacing head tube,
continueto end of figure.
1
3
2
45
6
9
78

OM-180 516 Page 5
ST-800 751-B
7/8 in
1/8 in
5/16 in
1 Secure head
tube in vice.
2 Remove switch
housing.
3 Loosen cable connec-
tor. Remove from vice
and turn head tube
out by hand.
Do not disturb cable connec-
tion between cable connector
and connector nut.
4 Slide handle.
1/8 in
5 Loosen set screws
on body and remove
head tube.
6 Install new head tube. Tighten set
screws to keep head tube in de-
sired position.
7 Hand-tighten head tube into cable connector. Place
head tube in vice and tighten to within 1/8 in (3 mm)
spacing between cable connector and body.
8 Reposition handle and
install switch housing
(see Section 8).
Install shock washer from
existing head tube.
YDisconnect gun first.
7. Replacing Head Tube (M-40)

OM-180 516 Page 6
ST-800 750
1 Switch Housing
2 Screw
Remove mounting screws from
switch housing.
3 Switch
4 Switch Leads
Carefullypull up on leads to remove
switch from housing.
5 Switch Lead Connectors
Remove switch lead connectors
from switch terminals and discard
old switch.
Push switch lead connectors onto
terminalsof new switch.
6 Switch Plunger
Insert switch back into switch hous-
ing until it snaps into place.
Install switch housing back onto
handle.
5/16 in
See Parts List for correct replacement parts.
Switch leads must
lay parallel.
1
2
4
3
6
5
8. Switch Replacement
9. Routine Maintenance
YDisconnectgun before maintaining.
Each Spool Of Wire
Blow Out
Gun
Casing
Clean
Nozzle
And Check
Contact Tip
3 Months
Control
Cord Gas Hose Gun Cable
Replace
Cracked
Parts

OM-180 516 Page 7
10. Troubleshooting
Trouble Remedy
Wire does not feed. Check contact tip. Check for kinks in gun cable.
Check gun trigger plug connection at welding power source/wire feeder.
Check, and if necessary, replace gun trigger switch.
Wire is not energized. Check contact tip.
Check gun trigger plug connection at welding power source/wire feeder.
Check, and if necessary, replace gun trigger switch.
Wire feeds unevenly. Check contact tip. Check for kinks in gun cable. Blow out liner and gun casing.
Weld porosity. Remove weld spatter buildup in nozzle.
Make sure inner support tube is tight in cable connector.
Check shielding gas flow/supply.
Wire feeding stops or does not feed
properlyduring welding. Straighten gun cable and/or replace damaged parts.
Adjust drive roll pressure (see wire feeder manual).
Change to proper drive roll groove (see wire feeder manual).
Readjust hub tension (see wire feeder manual).
Clean or replace wire inlet guide or liner if dirty or plugged.
Replace drive roll or pressure bearing if worn or slipping (see wire feeder manual).

OM-180 516 Page 8
11. Parts List
1
ST-801 725
234567 8
9
10
11
12 14 15
17 26
18
19
22
21
16
20
21 23
17
12
11 10
25
27
28
13*
*Includes Item 19
24
Figure 11-1. M-15 & M-25 Euro

OM-180 516 Page 9
Quantity
Description
Part
No.
Item
No. M-25
Figure 11-1. M-15 & M-25 Euro
Model
M-15
1 169 715 NOZZLE, slip type .500 orf flush 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 +169 724 NOZZLE, slip type .500 orf .125 recess 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 +169 725 NOZZLE, slip type .625 orf .125 recess 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 +169 726 NOZZLE, slip type .625 orf flush 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 +169 727 NOZZLE, slip type .625 orf .125 stickout 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2♦000 067 TIP, contact scr .030 wire x 1.125 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2♦000 068 TIP, contact scr .035 wire x 1.125 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 +000 069 TIP, contact scr .045 wire x 1.125 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 169 716 ADAPTER, contact tip 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 169 728 ADAPTER, contact tip 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 169 729 ADAPTER, nozzle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 170 470 RING, retaining 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 170 467 RING, retaining 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 170 471 O-RING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 170 468 O-RING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 169 717 WASHER, shock 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 169 730 WASHER, shock 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 169 718 TUBE, head 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 169 731 TUBE, head 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 169 738 NUT, locking handle 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 169 719 NUT, jam (gun end) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 169 732 NUT, jam 1 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 169 720 CONNECTOR, cable (gun end) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 169 733 CONNECTOR, cable 1 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 169 721 NUT, connector 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 169 734 NUT, connector 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 172 017 M15 UNICABLE CLAMP KIT, (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 172 018 M25 UNICABLE CLAMP KIT, (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 169 735 CLIP, compression 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 169 742 TUBE, support 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 169 743 CLAMP, inner 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 169 740 CLAMP, jacket 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 170 469 CLAMP, jacket 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 169 746 CONNECTOR, switch lead 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 169 739 SWITCH, trigger 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 172 691 HANDLE, (gun end) 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 169 741 STRAIN RELIEF, cable 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 602 177 SET SCREW 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 180 517 HANDLE, Euro 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24 180 514 COLLAR, threaded 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 173 521 CONNECTOR, feeder (consisting of) 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 079 974 O-RING, .500 ID x .103CS rbr 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 ♦172 258 KIT, liner monocoil .030/.035 wire x 15ft (consisting of) 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 +172 259 KIT, liner monocoil .035/.045 wire x 15ft (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28 079 975 O-RING, .187 ID x .103CS rbr 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
+These consumables are interchangeable for M-25 & M-25M models.
♦These consumables are interchangeable for all models.
BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS.

OM-180 516 Page 10
ST-801 726
Figure 11-2. M-40 Euro
123 4567 8
9
10
11
13 14
16 27
17
18
22
21
15
19
23
16
11 10
26
28
29
12
25
20 21

OM-180 516 Page 11
Description
Part
No.
Item
No.
Figure 11-2. M-40 Euro
Quanti
ty
1♦+169 724 NOZZLE, slip type .500 orf .125 recess 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 +169 726 NOZZLE, slip type .625 orf flush 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1♦+169 727 NOZZLE, slip type .625 orf .125 stickout 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1♦+169 725 NOZZLE, slip type .625 orf .125 recess 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1♦+176 243 NOZZLE, slip type tapered .375 orf x 2.640 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1♦+176 386 NOZZLE, slip type tapered .345 orf x 2.640 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1♦+176 238 NOZZLE, spot flat 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1♦+176 240 NOZZLE, spot inside corner 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1♦+176 242 NOZZLE, spot outside corner 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 +000 068 TIP, contact scr .035 wire x 1.125 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 +000 069 TIP, contact scr .045 wire x 1.125 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 +172 024 TIP, contact scr 1/16 wire x 1.125 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 +172 025 TIP, contact scr 5/64 wire x 1.125 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 +172 034 TIP, contact scr 3/64 wire x 1.125 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 169 728 ADAPTER, contact tip 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 169 729 ADAPTER, nozzle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 170 467 RING, retaining 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 170 468 O-RING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 169 730 WASHER, shock 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 169 744 TUBE, head 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 170 453 BODY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 170 452 CONNECTOR, cable 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 170 451 NUT, connector 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 169 690 M-40 UNICABLE CLAMP KIT, (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 170 461 CLIP, compression 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 170 459 TUBE, support 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 170 460 CLAMP, inner 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 170 457 CLAMP, jacket 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 169 746 CONNECTOR, switch lead 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 170 456 HOUSING, switch w/screws 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 170 454 HANDLE 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 170 455 SWITCH, trigger 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 170 458 STRAIN RELIEF, cable 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 602 177 SCREW, set .250-20 x .250 knrlpt sch stl 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 180 517 HANDLE, Euro 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24 180 514 COLLAR, threaded 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 180 515 CONNECTOR, feeder (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 180 515 O-RING, .500 ID x .103CS rbr 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 +172 259 KIT, liner monocoil .035/.045 wire x 15ft (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 +172 260 KIT, liner monocoil 1/16–5/64 wire x 15ft (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 +172 261 KIT, liner monocoil 3/64 aluminum wire x 15ft (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .
28 079 975 O-RING, .187 ID x .103CS rbr 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
♦OPTIONAL
+These consumables are interchangeable for both the M-40 and M-40AL models.
BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS.

OM-180 516 Page 12
Notes