Billebro BI-LD003A User manual

Instruction Manual
LED PAR 56
Model: BI-LD003A
PROFESSIONAL LED ·PROFESSIONAL LIGHTING

At first, thank you for purchasing the device. For the sake of safety and regular operation
of this projector, please read this manual carefully before using and operating.
Packing list：
：：
：
。。。。。。 a set of device
。。。。。 one user’s guide
User instruction：
：：
：
1. After unpacking, please check whether the projector has been damaged by transport such
as screw loosening, reflecting mirror broken, etc.
2. Check before electrification. Check whether the projector has been laid correctly
and stably, whether the voltage of the power is adapted to the requirement, otherwise we’ll
not be responsible for the damage of the light.
3. This projector is the first class protected equipment. Notice that while using the ground wires
have to connect to the earth properly by professionals. Please examine the electrics and
voltage before powering on it. Keep sure the supplied voltage stable and required. We
suggest customers apply a voltage regulator if necessary. It’ll check itself in seconds after
being electrified, could be used.
Technical Parameters:
Rated Voltage: AC230V
Rated Frequency: 50Hz
Rated power: 30W
Diodes Quantity: 151pcs diodes（10mm LED）
Channels: 4 Channels
Control signal: Standard DMX-512 signal
Function Model: DMX-512 controlled, Automatic, Master/slave
Working environment: Indoor use
Packing size: 23X23X35cm
FUNCTION MODEL SETTING:
This unit applies to Switch-address code, which is the choice of the mode of the performing
control and the address-code, the 10th address-code is the switch of the transferring of the
DMX-512 signal control, music control and automatic control. The mode set, details as
following
ON OFF Function
1，10 2，3，4，5，6，7，8，9 Connected one by one, then controlled by
DMX512
9，1，2，3,4，5，6，7，8，10 strobe
1,9 2,3,4,5,6,7,8 RGB strobe in turns slowly
2，9 1，3，4，5，6，7，8，10 RGB strobe in turns with increased speed
1，2，3，9 4，5，6，7，8，10 RGB color and patterns changed in times

DMX-512 Function:
The device adopts international standard DMX-512 signal, with totally 4 channels, details as
below:
Channels 512 Value Function
0-152 turn on from dark to bright
153-242 Strobe with speed increased
CH1 243-255 complete brighten
CH2 0-255 Red when CH1 turn on,brighten adjustable
CH3 0-255 Green when CH1 turn on,brighten
adjustable
CH4 0-255 Blue when CH1 turn on,brighten adjustable
Signal Connection
1. This product is assembled with DMX input and output 3 pins XLR socket, while all
connection is that Pin 1 is connected to the ground, Pin 2 is connected the negative pole
signal, Pin 3 is connected the Positive pole signal.
2. This product applies for 3 pins XLR socket, the connection of many units as following:
DMX512 CONTROLLER
INOUT
1
2
IN
OU T
P O W ER
I N
O U T
P OW E R
IN
OU T
P OW E R
N OTICE: 1. No overloading connection, the same branch without over 32 units.
2. Terminal matching connection，connect a resistance of1 20 ohms between the
Foot 2 and Foot 3 of DMX output Pin 3 socket of the last equipment of the branch.
DMX-512 address code set:
This unit is equipped with 4 channels, while the address code of the first light is 1, the
second is 2, the third is 3, and so on.
Detailed DMX-512 address code set as following:
Lighting NO. Original address（ID Value）Binary Code Dialing（ON）
1 1 1、10
2 2 1、5、10
3 3 1、6、10
4 4 1、5、6、10
5 5 1、7、10

Notice about Master-slave synchronization:
1. When the master machine is running, the light will send DMX-512 signals, however, it can’t
be connected to the controller, otherwise, they will interrupt each other , thus that can not
be synchronized.
2. While many lights are using master-slave synchronization, only one of them can be master,
or they can’t be synchronized.
The connection of Master-slave synchronization as below:
Safety Notice:
PLS be sure to turn off the device before installation and maintenance
PLS be sure when operating the device you have good ventilation.
This device is design for indoor use. PLS keep it dry whenever using. Install and
maintenance should be done by an Authorised dealer or service agent.
Do not use other voltage that not complied with the instruction showed.
Do not stare at the lighting source, it may damage you eyes.
Don not operate unless there is stable voltage.
Don not use it in a moist environment.
Maintenance:
We suggest that clean the light with professional glass cleaning and downy cloth. Keeping the
light clean regularly can not only get the largest power of the light.
6 6 1、5、7、10
7 7 1、6、7、10
8 8 1、5、6、7、10
9 9 1、8、10
10 10 1、5、8、10
··· ······ ······