Biostar BIPV10-IAP User guide

BIPV10-IAP Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents
Chapter 1: Introduction ........................................ 2
1.1 Before You Start ................................................................................ 2
1.2 Package Checklist............................................................................. 2
1.3 Mainboard Specification................................................................... 3
1.4 Rear Panel.......................................................................................... 4
1.5 Mainboard Layout ............................................................................ 6
Chapter 2: Installation.......................................... 7
2.1 CPU...................................................................................................... 7
2.2 Fan Header......................................................................................... 7
2.3 System Memory.................................................................................. 8
2.4 Power Supply ..................................................................................... 9
2.5 Onboard Slot/Connector/Header/Jumper.................................... 10
Chapter 3: BIOS Setup ........................................ 23
3.1 Main Menu........................................................................................ 25
3.2 Advanced Menu............................................................................... 28
3.3 PCI/PnP Menu.................................................................................. 39
3.4 Boot Menu ........................................................................................ 42
3.5 Chipset Menu.................................................................................... 44
3.6 Exit Menu.......................................................................................... 49
Chapter 4: Useful Help ........................................ 53
4.1 Driver Installation Note.................................................................. 53
4.2 AMI BIOS Beep Code....................................................................... 54
4.3 Troubleshooting............................................................................... 55

Mini-ITX Mainboard Manual
2
CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU START
Thank you for choosing our product. Before you start installing the
mainboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the system from power outlet
before operation.
Before you take the mainboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on mainboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the system from dangerous area, such as heat
source, humid air, and water.
Please switch on/off the machine normally. That is, DO
NOT pull out power cord directly from the mainboard
or the system may damage.
1.2 PACKAGE CHECKLIST
Mini-ITX Mainboard x 1
Fully Setup Driver CD x 1
I/O Bracket x 1
SATA Cable x 1 (Optional)

BIPV10-IAP
3
1.3 MAINBOARD SPECIFICATION
Specif ica tio n
CPU
Intel Atom CPU On-board
D425 @1.8GHz (TDP 10W)
Pineview-D Processor
Optional for:
N455 @1.66GHz (TDP 6.5W)
N550 dual core @1.5GHz (TDP 8.5W)
D525 dual core @ 1.8GHz (TDP 13W)
FSB Supports up 800 MHz
Chipset Intel NM10 Express Chipset
Graphic Intel Pineview-D integrated graphics engine
Max Shared Video Memory is 384 MB
--LVDS by CH7036 (24 bit single CH,
support up to 1366x768)
--Integrated VGA scale up to SXGA+
1400x1050)
Super I/O
ITE IT8728 + FINTEK F81216D
Provides the most commonly used legacy
Super I/O functionality.
128pin type
Environment Cont rol in it iat ives,
H/W Monitor
Fan Speed Controller
Main
Memory
SO-DIMM (204pin) Slot x 1
Supports DDR3 800 MHz
DIMM supports 512MB / 1GB / 2GB / 4GB
Max Memory Capacity 4GB
Registered DIMM or ECC DIMM is not
supported
* N455/N550 only support up to 2GB
SATA Chips et built - in Serial ATA controller SATA Version 2.0 specific ation compliant
Data transfer rates up to 3.0 Gb/s
LAN Realtek RTL 8111E 10 / 100 / 1000 Mb/s auto negotiation
Ha lf / Fu ll dup lex capab ility
Sound
Codec
Realtek ALC662
5.1 channels audio out (only for x3 audio
jack version)
High- Defin ition A udio s uppo rt
Amplifier Realtek ALC105 Class D, 2 channel Max. 2.8W
PCI slot x1
PCI Express x1 Slot x1Slot
Mini PCI-E Slot x1
SATA2 Connector x2
Power Connector for SATA x1
Front Panel Header x1
Parallel Connector x1
Digital I/O Connector x1
System Fan Header x2
On Board
Connectors
& Headers
Clear CMOS Header x1

Mini-ITX Mainboard Manual
4
Specif ica tio n
Speaker Box Connector x1
Amplifier Connector x2
PS/2 Keyboard/Mouse Connector x1
AT/ATX Power Switch Header x1
USB 2.0 Connector x1
LVDS Connector x1
LCD Power Select Header x1
LCD Backlight Power ON/OFF Header x1
LCD Backlight Inverter Connector x1
Inverter Power Select Header x1
Backlight Brightness Adjust Header x1
Serial Connectors (RS-232) x3
Power Connector (4pin) x1
Back Panel
I/O
DC Jack x1
RJ-11 Port x1
PS/2 Keyboard x1
Serial Port x3
VGA Port x1
RJ-45 Port x1
USB2.0 Port x4
Audio Jack (Line-out/Mic) x2
for cash drawer
Optional for x 3 (Line-in/Line-out/Mic)
Board Size
170 mm (W) x 170 mm (L) Mini-ITX
OS
Support
Windows XP/XPE, Linux Biostar reserves the right to add or remove
support for any OS with or without notice.
1.4 REAR PANEL
PS/2
Keyboard JCOM1B
Mic In
(Center/SUB)
Line Out
(F r on t )
USB 2.0 x 2 JCOM1A
RJ-45
VGA
COM3
DC RJ-11 USB 2.0 x 2

BIPV10-IAP
5
(1) DC 12V-in pin define
Pin Assignment
1 +12V DC_In
2 GND
3 GND
4 +12V DC_IN
Pin
1
Pin
2
Pin
3
Pin 4
(2) RJ-11 pin define (Pin #1 ~6 from right to left)
Pin 1
Pin 6
Ver. 1.0
Pin Define Status Pin Control Pin GPIO ADD
1 CASE OPEN#2 CASE OPEN#2 --- 63 A25H (bit3)
2 CASH1 _P --- CASH1 _P 40 A23H (bit0)
3 CASE OPEN# CASE OPEN# --- 36 A22H (bit6)
4 CASH_PWR --- --- --- ---
5 CASH2_P --- CASH2_P 47 A23H (bit7)
6 GND --- --- --- ---
Ver. 1.2
Pin Define Status Pin Control Pin GPIO ADD.
1 CASE OPEN#2 CASE OPEN#2 --- 63 A25H (bit3)
2 CASH1 _P --- CASH1 _P 14 A20H (bit4)
3 CASE OPEN# CASE OPEN# --- 64 A25H (bit4)
4 CASH_PWR --- --- --- ---
5 CASH2_P --- CASH2_P 47 A23H (bit7)
6 GND --- --- --- ---

Mini-ITX Mainboard Manual
6
1.5 MAINBOARD LAYOUT
JP 9
CN1
JVGA1
US B_
KBMS1
JRJ45US B1
JCOM1
A B
JAUDIO2
JCOM 5
JCOM6JCOM4
JPC5
JPC4
JPC6
JP1
JSFA N1
BAT1
SATA2
SATA1
JPRNT1
JDIO1
JP C2
JP C1
JSPK2
JSPK1
PCI1
PE1
JAT1
JCMOS 1
JPANEL1
BIOS
JSFAN2
JUSB1
J HDD1
LVDS -OUT 1
JC1
JBL1
JBL2
PEX1
DIMMA1
JKBMS1
JSPK3
JP WR1
JLV1
JPC3
JLV2
Intel
Atom
CPU
CPU1
NM10
Note: represents the 1■st pin.

BIPV10-IAP
7
CHAPTER 2: INSTALLATION
2.1 CPU
The mainboard includes an embedded Intel Atom N455/N550/D525/D425
processor, and a heatsink has been installed to provide sufficient cooling.
2.2 FAN HEADER
The fan header supports cooling-fans built in the system. The fan cable
and connector may be different due to the fan manufacturer.
JSFAN1: System Fan Header
Pin Assignment
1 Ground
2 +12V Smart
Fan Control (By
Fan)
3 FAN RPM rate
sense
1
3
JSFAN2: System Fan Header
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate
sense
13
Note:
System Fan Headers support 3-pin head connectors. When connecting with wires onto
connectors, please note that the red wire is the positive and should be connected to
pin#2, and the black wire is Ground and should be connected to GND.

Mini-ITX Mainboard Manual
8
2.3 SYSTEM MEMORY
DIMMA1: Memory Module (204pin SO-DIMM)
2 Align a DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
3 Insert the DIMM firmly into the slot until the retaining chip snap back in
place and the DIMM is properly seated.
Memory Capacity
DIMM Socket Location DDR3 Module Total Memory Size
DIMMA1 512MB / 1GB / 2GB / 4GB Max is 4GB.

BIPV10-IAP
9
2.4 POWER SUPPLY
JPWR1: ATX Power Source Connector (4-pin)
This connector provides +12V to system power circuit.
Pin Assignment
1 +12V
2 +12V
3 Ground
12
34
4 Ground
JHDD1: SATA Power Connector
This connector provides power connection of SATA devices.
Pin Assignment
1 +12V
2 GND
3 +3.3V
4 +5V
1 4

Mini-ITX Mainboard Manual
10
2.5 ONBOARD SLOT/CONNECTOR/HEADER/JUMPER
PCI1: Peripheral Component Interconnect Slot
This mainboard is equipped with 1 standard PCI slot. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards. This PCI
slot is designated as 32 bits.
PCI1
PE1: Mini PCI-E Slot
This mainboard is equipped with 1 Mini PCI-E Slot.

BIPV10-IAP
11
PEX1: PCI-Express x1 Slot
-PCI-Express 1.1 compliant.
-Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.
-PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
SATA1/SATA2: Serial ATA Connectors
These next generation connectors support the thin Serial ATA cable for primary
internal storage devices. The current Serial ATA interface allows up to 3.0
Gbit/s data transfer rate.
Pin Assignment
1 GND
2 TX+
3 TX-
4 GND
5 RX-
6 RX+
7 GND
147
SATA2
SATA1

Mini-ITX Mainboard Manual
12
JUSB1: USB 2.0 Connector
The mainboard provides 1 front USB pin connector, allowing up to 2 additional
USB 2.0 ports up to maximum throughput of 480 Mbps. Connect the USB
cable into the pin header for using high-speed USB interface peripherals.
Pin Assignment Pin Assignment
1 +5V (fused) 2 +5V (fused)
3 USB5- 4 USB7-
5 USB5+ 6 USB7+
7 Ground 8 Ground
9 Key 10 NC
1
210
9
JPANEL1: Front Panel Header
This 10-pin header includes Power-on, Reset, HDD LED, and Power LED
connection. It allows user to connect the system case’s front panel switch
functions.
91
210
Pin Assignment Function Pin Assignment Function
1 Key N/A 2 Power LED+
3 HD LED+ 4 Power LED+
5 HD LED- HDD LED 6 Power LED-
Power LED
7 Reset GND 8 Power
9 Reset Reset Button 10 Power GND
Power Button

BIPV10-IAP
13
JDIO1: Digital I/O Connector
This connector offers 4-pair of digital I/O functions and address is set in BIOS.
The default address is:
zDI01 -> 48CH BIT6-> GPIO6
zDI02 -> 48CH BIT7-> GPIO7
zDI03 -> 48DH BIT0-> GPIO8
zDI04 -> 48DH BIT1-> GPIO9
zDO01 -> 48DH BIT2-> GPIO10
zDO02 -> 48DH BIT5-> GPIO13
zDO03 -> 48DH BIT6-> GPIO14
zDO04 -> 48DH BIT7-> GPIO15
Pin Assignment
1 5V
2 Digital-In-6
3 Digital-Out-10
4 Digital-In-7
5 Digital-Out-13
6 Digital-In-8
7 Digital-Out-14
8 Digital-In-9
9 Digital-Out-15
1
2
9
10
10 GND
JKBMS1: Keyboard/Mouse Connector
The mainboard provides a PS2 pin header to attach a PS2 keyboard/mouse.
Pin Assignment
6 JUSBLAN1_POWER
5 GND
4 KB_DATA
3 KB_CLK
2 MS_DATA
1 MS_CLK
1
6

Mini-ITX Mainboard Manual
14
JCMOS1: Clear CMOS Header *
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
mainboard.
31
Pin 1-2 Close: (Default)
Normal Operation.
13
3
1
Pin 2-3 Close:
Clear CMOS data.
Clear CMOS Procedures:※
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
JAT1: AT/ATX Power Switch Header *
This header is for switching between AT and ATX power.
31
Pin 1-2 Close:
For AT Power
13
3
1
Pin 2-3 Close: (Default)
F o r AT X Po we r

BIPV10-IAP
15
JCOM1A/JCOM1B/JCOM3: Serial Port Connectors
The motherboard has 3 Serial Port Connectors for connecting RS-232 Port.
Pin Assignment
1 Carrier detect (DCD)
2 Received data (RXD)
3 Transmitted data (TXD)
4 Data terminal ready (DTR)
5 Signal ground (GND)
6 Data set ready (DSR)
7 Request to send (RTS)
8 Clear to send (CTS)
JCOM 1A
JCOM 1B
JCOM3
9 Ring or 5V or 12V (JCOM1A)
Ring or 5V (JCOM1B/JCOM3)
* Do not support RI wake up
JCOM4/JCOM5/JCOM6: Serial Port Connectors
The motherboard has 4 Serial Port Connectors for connecting RS-232 Port.
Pin Assignment
1 -PDCD
2 PSIN
3 PSOUT data
4 -PDTR
5 GND
6 -PDSR
7 -PRTS
8 -PCTS
9 -PRI
JCO M 4 JCO M 6
JCO M 5
1
9
2
10
10 5V or 12V

Mini-ITX Mainboard Manual
16
JPC1: Voltage Switch Header for JCOM1A
This header is for controlling the Pin 9 of JCOM1A to switch Ring, 5V, or 12V.
2
1
Pin 1-2 Close:
Pin9=Ring (Default)
4
3
Pin 2-3 Close:
Pin9=5V
51
62
6
5
Pin 2-3 Close:
Pin9=12V
JPC2: Voltage Switch Header for JCOM1B
This header is for controlling the Pin9 of JCOM1B to switch Ring or 5V.
31
Pin 1-2 Close:
Pin9=5V
31
3
1
Pin 2-3 Close:
Pin9=Ring (Default)
JPC3: Voltage Switch Header for JCOM3
This header is for controlling the Pin9 of JCOM3 to switch Ring or 5V.
31
Pin 1-2 Close:
Pin9=5V
31
3
1
Pin 2-3 Close:
Pin9=Ring (Default)

BIPV10-IAP
17
JPC4: Voltage Switch Header for JCOM4
This header is for controlling the Pin10 of JCOM4 to switch Ring or 5V.
31
Pin 1-2 Close:
Pin10=5V (Default)
3
1
3
1
Pin 2-3 Close:
Pin10=12V
JPC5: Voltage Switch Header for JCOM5
This header is for controlling the Pin10 of JCOM5 to switch Ring or 5V.
31
Pin 1-2 Close:
Pin10=5V (Default)
31
3
1
Pin 2-3 Close:
Pin10=12V
JPC6: Voltage Switch Header for JCOM6
This header is for controlling the Pin10 of JCOM6 to switch Ring or 5V.
31
Pin 1-2 Close:
Pin10=5V (Default)
31
3
1
Pin 2-3 Close:
Pin10=12V

Mini-ITX Mainboard Manual
18
JP1: Voltage Switch Header for Cash Draw Connector (CN1)
This header is for controlling the Pin4 of CN1 to switch 12V or 24V.
31
Pin 1-2 Close:
CN1=24V (Default)
31
3
1
Pin 2-3 Close:
CN1=12V
JSPK1/JSPK2: Amplifier Connectors
The mainboard provides 2 amplifier connectors.
JSPK1
Pin Assignment
1 SPKRN
2 SPKRP
JSPK2
Pin Assignment
1 SPKLN
2 SPKLP
12
JSPK2 JSPK1
JSPK3: Speaker Box Connector
The mainboard provides a speaker box connector.
Pin Assignment
1 LINEOUTL
2 GND_AUD
3 GND_AUD
4 LINEOUTR
1
4

BIPV10-IAP
19
LVDS-CONN1: LVDS Connector
This connector is for devices requiring display interface such as LVDS.
This connector supports 18/24 bit single-channel panels up to 1366 x 768
It is strongly recommended to use the matching JOY DAY INDUSTRIAL -
A1252WV-SF-2X20PD01 connector.
21
4039
Pin Assignment Pin Assignment
1 NC 2 PVDD (+3.3V or +5V or +12V)
3 NC 4 PVDD (+3.3V or +5V or +12V)
5 GND 6 GND
7 NC 8 GND
9 NC 10 LVDS1_TX0- (Differential signal)
11 GND 12 LVDS1_TX0+ (Differential signal)
13 NC 14 GND
15 NC 16 LVDS1_TX1- ( (Differential signal)
17 GND 18 LVDS1_TX1+ (Differential signal)
19 NC 20 GND
21 NC 22 LVDS1_TX2- (Differential signal)
23 GND 24 LVDS1_TX2+(Differential signal)
25 NC 26 GND
27 NC 28 LVDS1_CLK- (Differential signal)
29 +5V 30 LVDS1_CLK+(Differential signal)
31 I2C_CLK 32 GND
33 +3.3V 34 LVDS1_TX3-(Differential signal)
35 NC 36 LVDS1_TX3+(Differential signal)
37 PVDD (+3.3V or +5V) 38 GND
39 PVDD (+3.3V or +5V) 40 I2C_DATA