Biostar J1800TH User guide

J1800TH Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the contents
here and specially disclaims any implied warranties of merchantability or fitness
for any purpose. Further the vendor reserves the right to revise this publication
and to make changes to the contents here without obligation to notify any party
beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the brand
and product names are trademarks of their respective companies.
Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied

Table of Contents
Chapter 1: Introduction ...............................................................1
1.1 Before You Start......................................................................... 1
1.2 Package Checklist..................................................................... 1
1.3 Motherboard Specifications ....................................................... 2
1.4 Central Processing Unit (CPU).................................................. 3
1.5 Rear Panel Connectors ............................................................. 3
1.6 Motherboard Layout .................................................................. 4
Chapter 2: Hardware Installation................................................5
2.1 Connect Cooling Fans............................................................... 5
2.2 Install System Memory .............................................................. 5
2.3 Expansion Slots......................................................................... 6
2.4 Jumper Setting .......................................................................... 7
2.5 Headers & Connectors .............................................................. 9
Chapter 3: UEFI BIOS & Software.............................................14
3.1 UEFI BIOS Setup .................................................................... 14
3.2 BIOS Update ........................................................................... 14
3.3 Software................................................................................... 18
Chapter 4: Useful Help ..............................................................21
4.1 Driver Installation..................................................................... 23
4.2 AMI BIOS Beep Code.............................................................. 24
4.3 Troubleshooting....................................................................... 24
Appendix: SPEC In Other Languages......................................26
Arabic ......................................................................................................... 26
French ........................................................................................................ 27
German....................................................................................................... 28
Italian.......................................................................................................... 29
Japanese.................................................................................................... 30
Polish.......................................................................................................... 31
Portuguese ................................................................................................. 32
Russian....................................................................................................... 33
Spanish....................................................................................................... 34

J1800TH
1
CHAPTER 1: INTRODUCTION
1.1 Before You Start
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with sufficient
lighting.
Always disconnect the computer from power outlet before
operation.
Before you take the motherboard out from anti-static bag,
ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.
Avoid touching the components on motherboard or the rear
side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the case after
installation. Loose parts will cause short circuits which may
damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be 0 to
45 degrees Celsius.
To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
1.2 Package Checklist
Serial ATA Cable x2
Rear I/O Panel for ATX Case x1
Quick Installation Guide x1
Fully Setup Driver DVD x1
Note: The package contents may be different due to the sales region or models in which it was sold.
For more information about the standard package in your region, please contact your dealer or sales
representative.

Motherboard Manual
2
1.3 Motherboard Specifications
Specifications
CPU Support Intel® Celeron® J1800 processor
Memory
Supports Dual Channel DDR3L 1066/1333 (1.35V/1.5V)
2x DDR3L SO-DIMM Memory Slot, Max. Supports up to 16 GB Memory
Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L module
* Please refer to www.biostar.com.tw for Memory support list.
Storage 2x SATA 3Gb/s Connector, Supports Native IDE, AHCI Mode
LAN Realtek RTL 8111G
10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex capability
Audio Codec ALC662, 5.1 Channels, High Definition Audio
USB 6x USB 2.0 port (1 on rear I/Os and 5 via internal header)
1x USB 3.0 port (1 on rear I/Os )
Expansion Slots 1x mini PCIe Slot
Rear I/Os
1x DC-IN 19V Jack
1x VGA Port
1x HDMI Port
1x USB 3.0 Port
1x USB 2.0 Port
1x LAN port
2x Audio Jack (Mic-In, Line-Out)
Internal I/Os
2x SATA 3.0Gb/s Connector
1x SATA Power Connector
1x 2-Pin Power Connector
1x Front Panel Header
1x Front Audio Header
2x USB 2.0 2x5 Header (each header supports 2 USB 2.0 ports)
1x USB 2.0 1x5 Header
2x 4-Pin Fan Connector
1x Front Panel Display Connector (LVDS)
1x Front Panel Display Brightness Connector
1x Monitor Switch Header
1x Internal Stereo Speaker
1x Clear CMOS Jumper
1x LVDS Voltage Jumper
2x LVDS Jumper
1x Front Panel Display Voltage Jumper
1x Digital Microphone Header
Form Factor Thin Mini-ITX Form Factor, 170 mm x 170 mm
OS Support
Windows 7 / 8 / 8.1
Biostar reserves the right to add or remove support for any OS with or without
notice.

J1800TH
3
1.4 Rear Panel Connectors
Note 1: Since the audio chip supports High Definition Audio Specification, the function of
each audio jack can be defined by software. The input / output function of each audio jack
listed above represents the default setting. However, when connecting external microphone
to the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.
Note 2: Maximum resolution:
HDMI: 1920 x 1200 @60Hz
VGA: 2560 x 1600 @60Hz
1.5 Central Processing Unit (CPU)
The motherboard is equipped with an onboard Intel procrssor and a CPU cooler.
Model Name: Onboard CPU:
J1800TH Intel® Celeron® J1800 processor (Dual core, 1M Cache, 2.58 GHz)

Motherboard Manual
4
1.6 Motherboard Layout
Note 1: ■represents the 1st pin

J1800TH
5
CHAPTER 2: HARDWARE INSTALLATION
2.1 Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and
connector may be different according to the fan manufacturer. Connect the fan
cable to the connector while matching the black wire to pin#1.
SYS_FAN1/2: System Fan Header
Pin
A
ssignment
1 GND
2 +12V
3 Fan RPM rate sense
4 Smart Fan Control
Note: SYS_FAN1/2 support both 4-pin (PWM mode) and 3-pin (DC-Mode) smart fan
control. When connecting with wires onto connectors, please note that the red wire is the
positive and should be connected to pin#2, and the black wire is Ground and should be
connected to GND.
2.2 Install System Memory
A. DDR3L SO-DIMM Module (1.35V/1.5V)
Step 1: Align a DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

Motherboard Manual
6
Step 2: Insert the DIMM firmly into the slot until the retaining chip snap back in place
and the DIMM is properly seated.
Note1: The DIMM must be installed to DIMMA1 slot first.
Note2: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
B. Memory Capacity
DIMM Socket Location DDR3L Module Total Memory Size
DIMMA1 512MB/1GB/2GB/4GB/8GB Max is 16GB
DIMMB1 512MB/1GB/2GB/4GB/8GB
C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DIMMA1 DIMMB1
Disabled O X
Enabled O O
(O means memory installed, X means memory not installed.)
Note: The DRAM bus width of the memory module must be the same (x8 or x16)
2.3 Expansion Slots
MPCIE1: mini PCI Express slot
The mini PCIe slot supports half-length mini PCIe card.
Note1: Read the related expansion card's instruction document before install the expansion
card into the computer.
Note2: The slot does not support mSATA SSD.

J1800TH
7
2.4 Jumper Setting
The illustration shows how to set up jumpers. When the jumper cap is placed on
pins, the jumper is “close”, if not, that means the jumper is “open”.
Pin opened Pin closed Pin1-2 closed
JCMOS1: Clear CMOS Jumper
Placing the jumper on pin2-3, it s user to restore the BIOS safe setting and the
CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
Pin 1-2 Close:
Normal Operation (default).
Pin 2-3 Close:
Clear CMOS data.
※Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Load Optimal Defaults and save settings in CMOS.

Motherboard Manual
8
JRESOL_SEL1: LVDS Resolution Jumper
This jumper selects LVDS resolution.
Pin 1-3 & 2-4 Close:
1600 x 900 (default)
Pin 1-3 & 4-6 Close:
1920 x 1080
Pin 3-5 & 2-4 Close:
1366 x 768
Pin 3-5 & 4-6 Close:
N.A.
JLVDS_POWER1: LVDS Voltage Jumper
This jumper sets different screen voltage.
Pin 1-2 Close: 5V (default).
Pin 2-3 Close: 3.3V
JLVDS_BK1: Front Panel Display Voltage Jumper
This jumper selects the required operating voltage for the backlight panel.
Pin 1-2 Close: 19V (default).
Pin 2-3 Close: 12V
Caution: Incorrect voltage selection may damage the LVDS panel or inverter board.

J1800TH
9
2.5 Headers & Connectors
SATA_POWER1: SATA Power Connector
This connector provides the appropriate power connection to support both
HDDs and ODD.
Pin
A
ssignment
1 3.3V
2 3.3V
3 3.3V
4 Ground
5 Ground
6 Ground
7 5V
8 5V
9 5V
10 Ground
11 NC
12 Ground
13 12V
14 12V
15 12V
SATA1/2: Serial ATA Connectors
These connectors connect to SATA hard disk drives via SATA cables. It satisfies
the SATA 2.0 specification and with transfer rate of 3.0Gb/s.
Pin Assignment
1 Ground
2 TX+
3 TX-
4 Ground
5 RX-
6 RX+
7 Ground
JSPK1: Internal Stereo Speakers Header
The connector is for connecting Internal Stereo Speakers.
Pin Assignment
1 SPKRN
2 SPKRP
3 SPKLN
4 SPKLP

Motherboard Manual
10
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header supports HD and AC’97 audio front panel connector.
HD Audio AC’97
Pin Assignment Pin Assignment
1 Mic Left in 1 Mic In
2 Ground 2 Ground
3 Mic Right in 3 Mic Power
4 GPIO 4 Audio Power
5 Right line in 5 RT Line Out
6 Jack Sense 6 RT Line Out
7 Front Sense 7 Reserved
8 Key 8 Key
9 Left line in 9 LFT Line Out
10 Jack Sense 10 LFT Line Out
Note1: It is recommended that you connect a high-definition front panel audio module to this
connector to avail of the motherboard's high definition audio capability.
Note2: Please try to disable the "Front Panel Jack Detection" if you want to use an AC'97 front
audio output cable. The function can be found via O.S. Audio Utility.
PANEL1: Front Panel Header
This connector includes Power-on, Reset, HDD LED and Power LED
connections. It allows user to connect the PC case’s front panel switch functions.
Pin Assignment Function Pin Assignment Function
1 HDD_POWER_LED HDD LED 2 POWER_LED_MAIN Power LED
3 HDD_LED# 4 POWER_LED_ALT
5 GND Reset Switch 6 POWER_SWITCH# Power Switch
7 RESET_SWITCH# 8 GND
9 +5V_DC Power 10 Key None

J1800TH
11
F_USB1: Front Panel Dual USB 2.0 Header
The connector extends USB ports to the front panel of your system.
Pin Assignment
1 +5V DC
2 +5V DC
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
8 Ground
9 Key
10 NC
F_USB2: Internal Dual USB 2.0 Header
The connector connects to internal USB devices such as webcam, card reader
and touch panel.
Pin Assignment
1 +5V DC
2 +5V DC
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
8 Ground
9 Key
10 Key
F_USB3: Internal Single USB 2.0 Header
The connector connects to internal USB devices such as webcam, card reader
and touch panel.
Pin Assignment
1 +5V DC
2 USB-
3 USB+
4 Ground
5 Key
Note: This USB port is shared with mini PCIe slot.

Motherboard Manual
12
FPD1: Front Panel Display Brightness Connector
This connector provides an additional connector for powering the inverter or
driver board.
Pin Assignment
1 BKLT EN
(
volta
g
e:3.3V
)
2 BKLT PWM
3 BKLT PWR**
4 BKLT PWR**
5 BLK GND/Bri
g
htness GND
6 BLK GND/Bri
g
htness GND
7Bri
g
htness U
p
8Bri
g
htness Down
LVDS1: 40-pin LVDS Connector
This connector provides an internal 40-pin connector for flat panel display and
backlight connectivity.
Pin Assignment Pin Assignment
1 ODD_Lane3_P 2 ODD_Lane3_N
3 ODD_Lane2_P 4 ODD_Lane2_N
5 ODD_Lane1_P 6 ODD_Lane1_N
7 ODD_Lane0_P 8 ODD_Lane0_N
9 EVEN_Lane3_P 10 EVEN_Lane3_N
11 EVEN _Lane2_P 12 EVEN _Lane2_N
13 EVEN _Lane1_P 14 EVEN _Lane1_N
15 EVEN _Lane0_P 16 EVEN _Lane0_N
17 EDIE_GND 18 LCD_VCC*
19 LCD_VCC* 20 LCD_VCC*
21 N/C 22 EDID_3.3V
23 LCD_GND 24 LCD_GND
25 LCD_GND 26 ODD_CLK_P
27 ODD_CLK_N 28 BKLT_GND
29 BKLT_GND 30 BKLT_GND
31 EDIE_CLK 32 BLK_ENABLE
33 BKLT_PWM_DIM 34 EVEN_CLK_P
35 EVEN_CLK_N 36 BKLT_PWR**
37 BKLT_PWR** 38 BKLT_PWR**
39 N/C 40 EDIE_DATA
Note: * Voltage selected by JLVDS_POWER1. ** Voltage selected by JLVDS_BK1.

J1800TH
13
LCD_SW1: Monitor Switch
This header allows user to turn on or off the flat panel display backlight.
Pin Assignment
1MOMSW
2GND
JDMIC1: Digital Microphone Header
The connector is for connecting a digital microphone.
Pin Assignment
1 +3.3V
2 DMIC_DATA
3 Ground
4 DMIC_CLK
5Key
ATXPWR1: ATX Power Source Connector
The connector is for connecting a DC-19V power source.
Pin Assignment
1 +19V_IN
2 GND

Motherboard Manual
14
CHAPTER 3: UEFI BIOS & SOFTWARE
3.1 UEFI BIOS Setup
The BIOS Setup program can be used to view and change the BIOS
settings for the computer. The BIOS Setup program is accessed by pressing
the <DEL> key after the Power-On Self-Test (POST) memory test begins
and before the operating system boot begins.
For further information of setting up the UEFI BIOS, please refer to the UEFI
BIOS Manual in the Setup DVD.
3.2 BIOS Update
The BIOS can be updated using either of the following utilities:
BIOSTAR BIOS Flasher: Using this utility, the BIOS can be updated from a
file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a
CD-ROM.
BIOSTAR BIOS Update Utility: It enables automated updating while in the
Windows environment. Using this utility, the BIOS can be updated from a file
on a hard disk, a USB drive (a flash drive or a USB hard drive), or a
CD-ROM, or from the file location on the Web.
BIOSTAR BIOS Flasher
BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and simple
way to update your BIOS via USB pen drive.
Note1: This utility only allows storage device with FAT32/16 format and single partition.
Note2: Shutting down or resetting the system while updating the BIOS will lead to system boot
failure.
Updating BIOS with BIOSTAR BIOS Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, copy and save the BIOS file into a USB flash (pen) drive.
3. Insert the USB pen drive that contains the BIOS file to the USB port.
4. Power on or reset the computer and then press <F12> during the POST process.
5. After entering the POST screen,
the BIOS-FLASHER utility pops
out. Choose [fs0] to search for the
BIOS file.

J1800TH
15
6. Select the proper BIOS file, and a
message asking if you are sure to
flash the BIOS file. Click Yes to
start updating BIOS.
7. A dialog pops out after BIOS flash
is completed, asking you to restart
the system. Press the [Y] key to
restart system.
8. While the system boots up and the full screen logo shows up, press <DEL> key to
enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
BIOS Update Utility (through the Internet)
1. Installing BIOS Update Utility from the DVD Driver.
2. Please make sure the system is connected to the internet before using this
function.
3. Launch BIOS Update Utility and
click the Online Update button on
the main screen.

Motherboard Manual
16
4. An open dialog will show up to
request your agreement to start the
BIOS update. Click Yes to start the
online update procedure.
5. If there is a new BIOS version, the
utility will ask you to download it.
Click Yes to proceed.
6. After the download is completed,
you will be asked to program
(update) the BIOS or not. Click Yes
to proceed.
7. After the updating process is
finished, you will be asked you to
reboot the system. Click OK to
reboot.
8. While the system boots up and the full screen logo shows up, press <DEL> key
to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
BIOS Update Utility (through a BIOS file)
1. Installing BIOS Update Utility from the DVD Driver.
2. Download the proper BIOS from http://www.biostar.com.tw/
3. Launch BIOS Update Utility and
click the Update BIOS button on
the main screen.

J1800TH
17
4. A warning message will show up
to request your agreement to start
the BIOS update. Click OK to start
the update procedure.
5. Choose the location for your BIOS
file in the system. Please select
the proper BIOS file, and then
click on Open. It will take several
minutes, please be patient.
6. After the BIOS Update process is
finished, click on OK to reboot the
system.
7. While the system boots up and the full screen logo shows up, press <DEL> key
to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
Backup BIOS
Click the Backup BIOS button on
the main screen for the backup of
BIOS, and select a proper location
for your backup BIOS file in the
system, and click Save.

Motherboard Manual
18
3.3 Software
Installing Software
1. Insert the Setup DVD to the optical drive. The driver installation program would
appear if the Auto-run function has been enabled.
2. Select Software Installation, and then click on the respective software title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process is completed, you will see the software icon showing on
the desktop. Double-click the icon to launch it.
Note1: All the information and content about following software are subject to be changed without
notice. For better performance, the software is being continuously updated.
Note2: The information and pictures described below are for your reference only. The actual
information and settings on board may be slightly different from this manual.
BIOScreen Utility
This utility allows you to personalize your boot logo easily. You can choose BMP as
your boot logo so as to customize your computer.
Please follow the step-by-step instructions below to update boot logo:
Load Image：Choose the picture as the boot logo.
Transform：Transform the picture for BIOS and preview the result.
Update Bios：Write the picture to BIOS Memory to complete the update.