Bircher Reglomat RFGate 2 User manual



ON
12
2032
2032
+
+
ON
1234


   

 
12
Operating instructions
Startup
Sa ety and warning instructions
General
RFGate 2
➔Installation, startup, modification and retrofitting of the system may only be carried out by an electrician.
➔Switch off the operating voltage before working on the system.
➔The control unit may only be used to protect against dangers at crushing and shearing points on automatic gates (designated use).
Any other use is prohibited.
➔It is recommended to change the batteries annually.
Radio transmission system for evaluation of safety edges. The system consists of a transmitter unit and a receiver unit.
2
Electrical connection
1
Transmitter Receiver
Transmitter
PCB Transmitter
Terminals
Battery1 CR2032
Battery 2 CR2032
LED (activation)
DIP - Switch
Push button
Antenna
Receiver
PCB Receiver
Terminals
LED 1 (system readiness)
Push button
DIP - Switch
LED 2
(Programming mode)
Buzzer
Antenna
Con iguration Receiver / Transmitter3
1. Transmitter: insert the enclosed batteries (type CR2032). Important: insert battery 1 first and then battery 2! Unless this order is observed,
correct function is not guaranteed. The batteries must be suitable for use at temperatures of -20°C and above.
2. Connect receiver to supply voltage. (Note correct polarity for DC.)
The system has no fuse protection. It is advisable to include a fuse protection of minimum 100mA and maximum 250mA into the external power.
3. Configuration Receiver / Transmitter (➔chapter 3)
4. Carry out programming (➔chapter 4).
At startup, a minimum distance of 1m must be observed between the transmitter and receiver.
Safety edges
Transmitter inputs Receiver Output* (power off state) Test Remarks
Safetyedge
8k2
Limit
switch
0 V
+ 12 / 24 V
Test
CBS
Output*
1234567
8k2
CS
CB
We recommend:
1. Use a cable with a diameter
between 3,5 – 7,0 mm.
2. Use a cable with 6 cores
(from 0,25 mm2to 0,5 mm2).
Receiver functions Setting DIP-Switch Description
Power consumption:
“On”
11332244
ONON
Standard setting for safety operation
“Off”
11332244
ONON
Lover power consumption of transmitter ➔For storage only! Not for safety operation!
Transmitting frequency
Frequency 1
22331144
ONON
Setting MUST match that of transmitter, Frequency 869,85 MHz
(if frequency 2 is disrupted externally)
Frequency 2
22331144
ONON
Setting MUST match that of transmitter, Frequency 868,95 MHz,
Test input
NC
33
112244
ONON
Test contact NC, activated = contact open (npn transistor off)
NO
33
112244
ONON
Test contact NO, activated = contact closed (npn transistor on)
Automatic
frequency adjustment
“On”
44
112233
ONON
Automatic frequency adjustment switched on (only at very strong disrupted surroundings)
“Off”
44
112233
ONON
Automatic frequency adjustment switched off
*
*
*
*
*Factory settings
Standard:
with current control:
7
6
7
6
npn
open
collector
potentional free contact
or
Transmitter Receiver (Outputs / LEDs)
Safety edge Limit switch LED Out ut C-S Out ut C-B LED 1 LED 2
not actuated open OFF closed 8k2 ON OFF
actuated open flashes open closed OFF OFF
not actuated closed OFF closed 8k2 ON OFF
actuated closed flashes closed 8k2 ON OFF
Signal status (DIP-Switch at factory settings)

7023-06-0004c06/09
Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen, Switzerland, www.bircher-reglomat.com
Technical data
8Contact data
7Declaration o con ormity
Programming4
6
Manufacturer: Bircher Reglomat A , Wiesengasse 20, CH-8222 Beringen, Switzerland, declares
if used according to manufacturer's specifications, fulfills the fundamental requirements in acc. with Machinery directive 98/37/EC and EMC directive 2004/108/E
with following standards: EN 300 220, EN 301 489, EN 60730, EN 954-1 (Cat. 2)
Receiver Transmitter
Supply voltage 12 /24 VAC DC
Supply voltage
2x lithium battery 3 V DC
type CR2032 suitable for
down to -20°C
Transmitter memory 10
Output Relay, 24V, 0,5A,
micro disconnection 1B
Power
consumption
0.5 W @ 12 V,
1,2 W @ 24 V
Power
consumption
When transmitting: 17 mA,
in standby: 16 µA
Rated Transient
Over Voltage 330 V
Testing signal (Input)
or
eneral
Dimensions 130 x 35 x 15 mm
Working temperature - 20°– +55° C
Range > 10 m
Software Class A
Frequency bands 868.95 MHz & 869.85 Mhz
Protection class
acc. to IEC 60529 IP 55
Pollution degree 2
Ball pressure test
acc. to IEC 695-10-2
PCB: 125° C
Wrap: 75° C
Installation
5
A minimum distance of 1 m must be observed between the transmitter and receiver.
1. Install transmitter on gate. Please note: cable outlet at bottom!
2. Wire safety edge to transmitter.
3. Install receiver and wire to control unit.
The devices RF ate transmitter and RF ate receiver must be mounted on separate surfaces.
Transmitter functions Setting DIP-switch Description
Safety edge type
Safety edge
resistance
11
22
ONON
Standard safety edge resistance 8.2 kohm
Safety edge
contact
11
22
ONON
Safety edge (NO, without terminating resistor) ➔no safety category 2!
Transmitting frequency
Frequency 1
22
11
ONON
Setting MUST match that of receiver, Frequency 869,85 MHz
Frequency 2
2
2
1
1
ONON
Setting MUST match that of receiver, Frequency 868,95 MHz
*
*
*Factory settings
Activate programming mode
Receiver:
Activate programming mode
Store transmitter code (Programming mode has to be activated)
Store transmitter code
Store additional transmitter codes
Reached maximal amount of transmitters (10)
(Transmitter memory full)
Finish programming
Reset
1.5 s
1.5 s
1.5 s
release
release
release
Receiver: 1 x Bee
Receiver : 1 x Bee
10 sec Bee
Receiver :
2 x Bee
Delete all stored codes
(Receiver) 3.5 s
1.5 s
Receiver :
Receiver :
Wait 10 sec
1 x Bee
release
Receiver : 1 x Bee Receiver : Series of
Bee s
...
...
Receiver :
Receiver:
Transmitter:
Transmitter:
Receiver:
Transmitter:
Transmitter:
Transmitter
Safety edge
4. Switch on voltage.
5. Carry out test by actuating the connected safety edge in different gate positions, particularly the open and closed positions.
7
6
7
6
npn
open
collector