Bison BA832 User manual

1
Item Qty Description Item Qty Description
A 1 Portable Base and Pole Assembly J 1 Acrylic Backboard Hardware (pkg. w/ backboard)
B 1 Extension Arm Assembly K 1 Backboard (pkg. separately)
C 2 Upper Backboard Support Brackets (BA832/833) L 1 Goal (pkg. separately)
D 2 Lower Backboard Support Brackets (BA832/833) M 1 Goal Mounting Hardware (pkg. separately)
E 4 Backboard Mounting Angles (BA832/833) N 4 5/16” X 1 1/2” Carriage Bolt (BA832)
F 8 5/16” X 1” Hex Bolts (BA832/833) O 1 Locking Pin
G 12 5/16” Flange Nuts (BA832/833) P 1 Lock Knob
P A R T S L I S T
H 8 5/16” Flat Washers (BA832/833) Q 1 Backboard Mounting H-Frame (BA833XL)
I 1 Height Indicator Labels (attached to base)
Warning!
Do not release the height adjustment handle or loosen the telescoping pole lockbolt until the system is
completely assembled as the telescoping tubes are under spring tension and may cause damage or injury to
the assembler.
 Inspect all contents prior to installation. Report any missing parts to dealer immediately.
 Carefully read all instructions before proceeding. Pay special attention to the safety instructions on the next page.
 Save this instruction in the event that the manufacturer must be contacted in the future for maintenance
information.
Date: 11/27/2018 Rev: 8 B.A. N.J.C. File: \pub\ba833 Ref#: 930306
—— Instruction Manual ——
BA832/833/833XL
Portable/Adjustable Basketball Systems Customer Service
[phone]
1. This basketball system is shipped partially
preassembled. After removing the system from its
shipping skid open the lower padded front of the
unit by removing the Lock Knob (P) and pulling
forward on the top of the lower pad. Remove the
unassembled parts and hardware. See Figure 1.
2. For BA832/833 open the rear ballast storage
compartment by removing 4 screws. Do not
remove the bottom 2 pivot screws. Pivot rear
cover open and place 12 each 4”x 8”x 16” solid
Concrete CAP Blocks and 3 each 4”x 8”x 8” Solid
Concrete CAP Blocks into the compartment.
Make sure that the weight is evenly distributed.
Reposition the rear cover.
See Layout 1.
P
Figure 1

2
3. For BA833XL open the rear ballast storage compartment by
removing 4 screws. Do not remove the bottom 2 pivot screws.
Pivot rear cover open and place 24 each 4”x 8”x 16” solid
Concrete CAP Blocks into the compartment. Make sure that the
weight is evenly distributed. Reposition the rear cover.
See Layout 2.
4. Rotate the Extension Arm Assembly (B) to the playing position.
See Figure 1
5. For Model BA833XL use the instructions supplied with the
Backboard Mounting H-Frame (Q) you have purchased and
pre-assemble the Backboard (K) and the Backboard Mounting
H-Frame (Q). See Figure 2.
6. For Model BA833, mount the Upper Backboard Supports (C)
and Lower Backboard Supports (D) to the Extension Arm
Assembly (B) using the 5/16”X 1” Hex Bolts (F), 5/16” Flat
Washers (H) and the 5/16” Flange Nuts (G). Do not tighten at
this time. For Model BA832 only requires the Upper Backboard
Supports (C), discard Lower Backboard Supports (D).
See Figure 3 & 4.
7. Mount the Backboard Mounting Angles (E) to the Backboard
Supports (C) and (D) as shown in Figure 3, using the 5/16”X 1”
Hex Bolts (F) and 5/16” Flange Nuts (G). Do not tighten at this
time. See Figure 3 & 4.
Note:
If your warning label becomes
damaged or lost, call the
manufacture for a replacement.
BA832/833
Layout 2
BA833XL

3
8. On BA832 systems attach 2 Backboard Mounting Angles (E) to the Backboard (K) using 5/16 x 1 1/2”
Carriage Bolts (N), 5/16” Flat Washers (H) and 5/16” Flange Nuts (G). On BA833 systems attach the 4
Backboard Mounting Angles (E) to the Backboard (K) using the Acrylic Backboard Hardware (J).
Follow the instructions provided with the hardware marked “BAACRYLIC”. See Figure 4 and 5.
9. Mount the Backboard (K) and Goal (L) to the Extension Arm Assembly (B) using the hardware
provided with the Goal (M). See Figures 2,4, and 5.
10. Tighten all hardware assuring that the goal and backboard are level.
11. Install net provided with goal.
12. To adjust the height of the rim loosen the telescoping lock bolt, then loosen the lock handle while
gripping the adjustment handles. Adjust the pole upwards until the top of the goal measures 10’ from the
playing surface. Lock the pole at that height and apply the 10’ Height Indicator Label (I) to the plated
inner tube. Line up the arrows on the 10’ label to the already attached “Rim Height Indicator” label.
Adjust the pole downward so that the goal measures 9’ 6” from the playing surface. Lock the pole and
apply the appropriate height indicator label to the plated inner tube. Continue to lower the goal at 6”
increments, being careful to lock the pole each time, and apply the appropriate height labels until the
height of 8’ from playing surface is reached. See Figure 6
13. To roll the system, unscrew the Lock Knob (P) to release the lower front padding. This will lower the
unit to the portable position. To lock in place push padding to the original position and tighten the Lock
Warning!
The recent popularity of adjustable height basketball systems has increased the risk of dental injury,
particularly to young players, due to players getting their teeth caught in the net.
G
E
F
EC
B
GH
F
D
Figure 3
BACKBOARD MOUNTING
GOAL HARDWARE (M)
(provided with goal)
GOAL (L)
BACKBOARD (K)
H - FRAME (Q)
Figure 2

4
Knob (P) . See Figure 1
14. For storage or transport through a normal 78” tall double doorway: remove the Locking Pin (O)
then pivot the extension arm, backboard and goal downwards. Store the Locking Pin (O) in the extension
arm. See Figure 1.
15. To roll the system, unscrew the Lock Knob (P) to release the lower front padding. This will lower the
unit to the portable position. To lock in place push padding to the original position and tighten the Lock
Knob (P) . See Figure 1.
Warning!
Never use the backboard to push or pull the system as
unwarranted backboard breakage will likely occur.
Figure 4
K
Figure 5 Figure 6