Bison FH200 User manual

1
P A R T S L I S T FOR ONE PAIR OF GOALS
Item Qty Description Item Qty Description
A 2 Crossbar I 24 3/8” Flat Washer
B 4 Goal Side J 2 Net (Packaged Separately)
C 2 Spreader Frame K 50 Net Clips
D 4 Crossbar Bracket L 2 Hook and Loop Fastening Strap (Roll)
E 12 3/8” X 3” Hex Bolt M 4 3/8” X 4” Eyebolt
F 4 3/8” X 4” Hex Bolt N 4 Washer Plate
G 20 3/8” Hex Nut O 4 Ground Anchor (Packaged Separately)
H 20 3/8” Lock Washer
♦ Inspect all contents prior to installation. Report any missing parts to dealer immediately.
♦ Read all instructions before proceeding.
—— Instruction Manual ——
FH200
Official Outdoor Field Hockey Goal
Date: 1.24.08 Rev: I.R. B.A. N.J.C. File: \pub\fh200inst Ref#: 840025
Customer Service
[phone]
IMPORTANT SAFETY INSTRUCTIONS!
1. Check for structural integrity and proper connection hardware before every use. Replace damaged or
missing parts or fasteners immediately.
2. Ensure safety/warning labels are clearly visible (placed under the crossbar).
3. Securely anchor or counterweight movable field hockey goals at ALL times.
4. Always instruct players, managers, coaches, trainers, teachers, maintenance and all other personnel
who might come into contact with the goal on the safe handling of and potential dangers associated
with movable field hockey goals.
5. Always exercise extreme caution when moving goals and allow adequate manpower to move goals of
varied size and weights. Movable field hockey goals should only be moved by authorized and trained
personnel.
6. NEVER allow anyone to climb on the net or goal framework.
7. Most tip over injuries occur when goals are unattended. Unless area is secure fully disassemble or
store in a place where children cannot have access to them.
Warning!
It is imperative that all Portable Field Hockey Goals be used in accordance with the safety guidelines
contained in these instructions as well as those found on the safety warning labels attached to the goals.
Failure to do so can cause serious injury or death.

2
Notice:
Factory installed kick boards must face the inside of the goal with the tubular frame on the outside.
1. Using the 3/8” X 3” Hex Bolts (E), Washer Plate (N), 3/8” Lock Washers (H) and 3/8” Hex Nuts (G)
install a Crossbar Bracket (D) to the inside of each Goal Side (B). See Illustration.
2. Use the 3/8” X 3” Hex Bolts (E), 3/8” Flat Washers (I), 3/8” Lock Washers (H) and 3/8” Hex Nuts (G)
to assemble both Goal Sides (B) to Crossbar (A) by fitting Crossbar (A) over Crossbar Bracket (D) on
both ends. See Illustration.
3. In the top holes on both Goal Sides (B) use the 3/8” X 4” Hex Bolts (F), 3/8” Flat Washers (I), 3/8”
Lock Washers (H) and 3/8” Hex Nuts (G) to attach Spreader Frame (C) to Goal Sides (B).
See Illustration.
4. Use 3/8” X 4” Eyebolts (M), 3/8” Flat Washers (I), 3/8” Lock Washers (H) and 3/8” Hex Nuts (G) in
the bottom holes on both Goal Sides (B) to attach Spreader Frame (C) to Goal Sides (B).
See Illustration.
5. Once goal is assembled install Net Clips (K) along Crossbar (A) and upright poles on Goal Sides (B)
every 24”. The Net Clips (K) are designed to slip into the slot then twisted 90 degrees to attach. Drape
Net (J) over the outside of entire Field Hockey Goal, use the Net Clips (K) and cut pieces of Hook and
Loop Fastening Strap (L) as needed to secure Net (J) into position.
6. Insert Ground Anchors (O) into the ground directly behind each back corner of the goal and carabiner
clip to 3/8” X 4” Eyebolt (M). Securely anchor movable field hockey goals at ALL times.

3
A
D
E
E
F
GHI
GH
C
GH
M
I
I
I
N