Karakoram Prime Quick setup guide

PAGE 1 OF 6
Prime Instructions_A05
Prime Splitboard System
www.splitboardbindings.com
Assembly and Use Instructions
Hardware:
-M3 Allen Wrench (Highback Fwd Lean, Heel Lever Size Adjustment)
-Cresent Wrench or 8 mm socket
Women's: W6-W8
Large:11.5-13
(Heel Lever Size Adjustment)
(Binding Hardware, Interfaces)
Medium: 8.5-11
Tools:
-M4 Allen Wrench
Size Chart:
Small: 6-8
Scan QR Code for
video instructions or visit
Patented US8469372B2, US8733783B2, US9138628B2, 9937407B2 and Patents Pending
1x Ride Mode 2.0 - Left
2x Dual-Speed Risers
with Heel Lockdown
2x Tour Modes
1x Ride Mode 2.0 - Right
8x
Ride Mode 2.0
M6x14mm Flathead Screw
M6x10mm Buttonhead Screw
6x Tour Mode
4x for DualSpeed Risers
6x extra for Tour Mode with thin core boards
instagram.com/karakorambc
(L and R)
www.karakoram.com
2x Bindings
facebook.com/karakorambc
10x M6x8mm Buttonhead Screw

6x
Set Toeside Stance Angles Preset Angles:
Front Foot: 30° max, -10° min
Back Foot: 10° max, -30° min
For greater than 10° on Back Foot
PAGE 2 OF 6
Prime Instructions_A05
4x M6x8mm Buttonhead
Screw
Angles in 3° increments
Left
Production Splitboard Installation
1.
2.
M6x10mm Buttonhead Screw
Use M6x8mm Buttonhead
for thin core boards
Riser Positions:
-Prime Connect: All the way back
-Prime SL: All the way back
-Prime-X: All the way forward
C. Reinstall Hardware
Angle Plate
A. Remove Hardware
B. Flip Angle Plates
Right

PAGE 3 OF 6
Prime Instructions_A05
3.
Loosely tighten screws on1.
toeside and heelside of Ride
Mode 2.0
Align heelside angle to2.
match toeside angle
Match alignment arrows and align3.
seam marks with seam of splitboard
Tighten screws4.
Test fit bindings5.
R
8x M6x14mm Flathead Screw
Seam Mark Alignment
Arrows
Alignment
Arrows
Seam Mark
Seam of Splitboard
Heelside Angle

4a. Binding Size Adjustment- PRIME SL
Size Setting:
S: 6-7
M:8.5-9.5
L: 11.5
W: W6-W7
Size Setting:
S: 7-8
M:9.5-11
L: 12-13
W: W7-W8
Forward Lean Adjustment:
Bindings come set
at 11°/18° fwd lean
USE 4b. for Prime-X
and X-Carbon
PAGE 4 OF 6
Prime Instructions_A05
LARGE POSITION
22°
11°
3.
!loose on ride mode.
mount to Ride Mode or if binding is
Only adjust if binding is too tight to
Loosen Toestay screws1.
Adjust Toestay fore/aft as desired2.
Tighten Toestay screws
5. Binding Adjustment
0°
0°
SMALL POSITION
10°
11°

PAGE 5 OF 6
Prime Instructions_A05
4b. Binding Size Adjustment- PRIME-X and X-Carbon
ATTENTION
If adjusting to LARGE POSITION, you MUST shift the
Toestay and the Heelstay to the LARGE POSITION.
!
LARGE POSITION
(Bindings come in this position)
SMALL POSITION
Heelstay
(Under rubber pad)
E.
Tighten all ScrewsF.
Reinstall Forward Screws in LARGE POSITION
D.
Forward Screws
To shift bindings to LARGE POSITION:
Remove six Forward ScrewsA.
Loosen two Rear ScrewsB.
Slide Heelstay forwardC.
Shift Toestay forward
Rear Screw
Toestay

Prime Splitboard System Use Instructions
Attach binding to Ride2.
Mode, aligning Toe Catch
and Ride Mode Toe
Attachment
Close Heel Lever and Lanyard3.
Ride Mode:
Open Heelcup Lever1.
Dual-Speed Riser:
Operation:
Slide basket of ski pole under tall riser to flip up1.
Flip riser to short position or long position with tip of ski pole2.
Lower riser by pushing on tall riser towards tail of ski3.
Heel Lock Operation:
Flip Heel Lock up1.
Close Heelcup Lever to2.
engage pins with Heel Lock
PAGE 6 OF 6
Prime Instructions_A05
Heel Lock
0° Rise
Slide basket
under here Short 12° Rise
V
Toe Pins
Tall 20° Rise