BitFenix phenom mini-itx Operator's manual

Quick Installation Guide

Box Contents
* Contents and specificaons subject to change without noce.
•Phenom Mini-ITX Case
•Phenom Mini-ITX Quick Installaon Guide
oScrews:
Thumbscrews M3: x 4 (For 5.25" drive bay adapter)
Standard Screw 6-32 Hex: x 4 (For PSU)
Standard Screw 6-32*6mm Flat: x 7 (For MB)
Standard Screw 6-32*10mm Round: x 5 (For securing HDD trays)
Standard Screw M3*5mm Round: x 12 (For 2.5" SSD)
oAccessories:
Cable Clip: x 1
5.25" drive bay adapter: x 1
01

Removing side panels
a. Remove side panelsb.Remove thumbscrews
Basic Installaon
Front Top Back Side
a
b
02

d. If needed, add extra 6-32*10mm
Round screw for increased stability
Installing 3.5" drives
a. Remove hard disk tray b. Install drive by bending rails of
c. Slide tray into place
tray to the side
03

b. Install drive using M3*5mm Round
screws
c. Slide tray into place
a. Remove hard disk tray
Installing 2.5" drives
04

a. Remove FlexCage™ and posion
drive(s) on PSU cage
c. Remove FlexCage™ and posion
drive on floor
d. Secure with screws (M3*5mm Round)
b. Secure with screws (M3*5mm Round)
Installing 2.5" drives
05

Installing 2.5" drives
a. Slide drives into place b. Secure with screws (M3*5mm Round)
06

D. Reset buon
B. Headphone jack
C. Microphone jack
A. SuperSpeed USB3.0 ports
E. Power buon
D
E
A
B
C
07

a. b.Remove top filter Install fans
c. Secure with screws
Top Fan Installaon (120mm)
d. Replace top filter
08

Front Fan Installaon
b. Install fans (If necessary, remove
FlexCage™)
c. Secure with screws
a. Remove front panel by pushing
tabs from inside chassis
09

a. b.Install fan Secure with screws
Rear Fan Installaon
10

FlexCage™ Hard Disk Rack
Removing FlexCage™
b. Remove screws from boom of
HDD cage
a. Remove plasc rail
b. Pull to removea. Press tabs on HDD cage
11

Rotang FlexCage™
b. Secure screws from boom of
HDD cage
a. Remove and rotate the HDD cage
d. Insert HDD cage from other sidec. Rotate the plasc rail and secure
screws
a
b
12

Power Supply Installaon
b. Secure PSU Back Plate on PSU
(Standardscrew 6-32 hex)
a. Remove PSU Back Plate
d. Secure with screwsc. Slide PSU into place
13

a.
c.
b. Use A or B depending on device
d. Secure with screws
(
Thumbscrews M3 )
A B
Install device using M3*5mm Round
screws
Slide tray into place
Installing 5.25" drive bay adapter
14

PSU Filter
PSU Filter
15

Ver 1.0 : 2013/09
Bitfenix Co., Ltd.
3F, No.79, Sec. 1, Xintai 5th Rd.,
Xi Zhi District, New Taipei City, Taiwan, R.O.C.
For the most updated information, please visit our official website: http://www.bitfenix.com
© 2013 BITFENIX Co., Ltd. All Rights Reserved. All trademarks are registered to their respective owners.
16