Black & Decker BWDS User manual

INSTRUCTION MANUAL
WASHER DRYER STAND
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR
ANY REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet, call
844-299-0879 from 10:30 a.m. to 6:30 p.m. EST Mon. - Fri. to speak with an
agent. Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
CATALOG NUMBER
BWDS

Page 2
Thank you for purchasing our
BLACK+DECKER product. This
easy-to-use manual will guide you
in getting the best use of your
washer dryer stand.
Remember to record the model and
serial numbers. They are on a label
on the rear.
Staple your receipt to your manual. You will need it to obtain warranty service.
Model number
Serial number
Date of purchase
PRODUCT REGISTRATION
CONTENTS
SAFETY INFORMATION
Important Safety Instructions.............................................................................................................................................. 2
SET UP & USE
Parts List....................................................................................................................................................................................3-4
Assembly Instructions.......................................................................................................................................5-9
CLEANING & CARE.............................................................................................................................................. 10
TROUBLE SHOOTING & WARRANTY
Customer Service.................................................................................................................................................. 10
Limited Warranty .....................................................................................................................................................................11
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
1. READ ALL INSTRUCTIONS BEFORE USE
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
WARNING:
• Maximum Weight for Dryer Rack 100 lbs. Do not exceed maximum
weight limit.
• This dryer must be anchored to a wall using anti-tip
brackets to avoid tipping.
• Some assembly parts may cause choking. Keep away from children.
• Do not lean on, or allow children to play or climb on the washer dryer
stand. Do not allow children to hang from the door of the dryer when
seated on the top of the washer dryer stand because this could cause
tipping.

Page 3
SET UP & USE
PARTS LIST
Tools Required: Screwdriver and Drill

Page 4Page 4
SET UP & USE
ID DESCRIPTION QUANTITY
A LEFT DRYER SUPPORT 1
A1 RIGHT DRYER SUPPORT 1
A2 NON-SLIP PAD 4
B LEFT BASE 1
B1 RIGHT BASE 1
C UPPER LEFT FRONT VERTICAL POLE 1
C1 UPPER RIGHT FRONT VERTICAL POLE 1
D UPPER LEFT REAR VERTICAL POLE 1
D1 UPPER RIGHT REAR VERTICAL POLE 1
E LOWER LEFT REAR VERTICAL POLE 1
E1 LOWER RIGHT REAR VERTICAL POLE 1
F LOWER LEFT FRONT VERTICAL POLE 1
F1 LOWER RIGHT FRONT VERTICAL POLE 1
G HORIZONTAL SUPPORT BEAMS 3
H ANTI-TIP BRACKET 2
I CONNECTING RAIL 2
J DIAGONAL SUPPORT RAIL 2
K LONG BOLTS 6
L SHORT BOLTS 4
M SCREWS 12
N BUTTERFLY NUT 10
O DRYWALL SCREWS WITH ANCHOR 2 sets

Page 5
SET UP & USE
ASSEMBLY INSTRUCTIONS
1. Using the diagram below as reference to position the poles, INSERT E (LOWER
LEFT REAR VERTICAL POLE) and F (LOWER LEFT FRONT VERTICAL POLE) into
B LEFT BASE.
Use (1) M (SCREW) to secure on each side.
2. Insert D (UPPER LEFT REAR VERTICAL POLE) into E (LOWER LEFT FRONT
VERTICAL POLE).
Insert C (UPPER LEFT FRONT VERTICAL POLE) into F (LOWER LEFT FRONT
VERTICAL POLE), Line up I (CONNECTING RAIL) with the holes on the front and
rear poles as shown and secure using (1) M (SCREW) on each side.

Page 6
SET UP & USE
3. Align A (LEFT DRYER SUPPORT) and insert into C (UPPER LEFT FRONT
VERTICAL POLE) and D (UPPER LEFT REAR VERTICAL POLE), use (1) M (screw)
on each side to secure.
Follow the same steps to assemble the right side:
INSERT E1 (LOWER RIGHT REAR VERTICAL POLE) and F1 (LOWER RIGHT
FRONT VERTICAL POLE) into B1 RIGHT BASE. Use (1) M (SCREW) to secure on
each side.
Insert D1 (UPPER RIGHT REAR VERTICAL POLE) into E1 (LOWER RIGHT REAR
VERTICAL POLE).
Insert C1 (UPPER RIGHT FRONT VERTICAL POLE) into F1 (LOWER RIGHT FRONT
VERTICAL POLE),
Line up I (CONNECTING RAIL) with the holes on the front and rear poles as
shown and secure using (1) M (SCREW) on each side.
Align A1 (RIGHT DRYER SUPPORT) and insert into C1 (UPPER RIGHT FRONT
VERTICAL POLE) and D1 (UPPER RIGHT REAR VERTICAL POLE), use (1) M
(SCREW) on each side to secure.
C
AA1
D1
E1 F1
B1
C1
Left side Right side
D
II
B
EF

Page 7
4. Attach G (HORIZONTAL SUPPORT BEAMS) to the top and bottom of the left rear
pole and the top of the left front pole as shown.
Insert K (LONG BOLT) through the holes of the pole and N (BUTTERFLY NUT) on
the opposite side of the pole. Turn the BUTTERFLY NUT clockwise to secure but
do not tighten completely.
5. Secure the right side with K (LONG BOLTS) and N (BUTTERFLY NUT), but do not
tighten completely.
N
SET UP & USE
K
N

Page 8
6. Align the holes in H (ANTI-TIP BRACKET), J (DIAGONAL SUPPORT RAIL) and D
(UPPER LEFT REAR VERTICAL POLE) as shown. The other end of J (DIAGONAL
SUPPORT RAIL) should be attached to E1 (LOWER RIGHT REAR VERTICAL
POLE).
Insert L (Short bolt) through the hole in H (ANTI-TIP BRACKET) first to secure
with N (butterfly nut) on the opposite side.
7. Align the holes in H (ANTI-TIP BRACKET), J (DIAGONAL SUPPORT RAIL)
and D1 (UPPER RIGHT REAR VERTICAL POLE) as shown. The other end of J
(DIAGONAL SUPPORT RAIL) should be attached to E (LOWER LEFT REAR
VERTICAL POLE).
Use N (butterflynut) and L (Short bolts) to secure.
SET UP & USE
E1
D
Butterfly Nut
D1 D
HH
J
J
E1 E

Page 9
SET UP & USE
8. Tighten all the screws and butterfly nuts and move the stand to where you intend
to attach it to the wall.
9. Mark the position on the wall where the holes on H (ANTI-TIP BRACKET) will
connect to the wall to mark the location of O (DRYWALL SCREWS WITH
ANCHOR). Drill a hole in the wall slightly smaller than the diameter of the plastic
wall anchor. Insert the wall anchor securely into the hole so the plastic anchor is
flush with the wall. Using a Philips head screwdriver, insert the screw through the
hole in the H (ANTI-TIP BRACKET) and into the plastic anchor.
10. Place A2 (NON-SLIP PAD) on both A (LEFT DRYER SUPPORT) and A1 (RIGHT
DRYER SUPPORT).
A2 A2
A2 A2

Page 10
CLEANING AND MAINTENANCE
Use water or a mild soap and water solution to clean your washer dryer stand. Do not
use abrasive cleaners which may scratch the surface.
SET UP & USE
TROUBLESHOOTING & WARRANTY
IMPORTANT
DO NOT RETURN THIS PRODUCT TO THE STORE
If you have a problem with this product, please contact the
BLACK+DECKER Customer Satisfaction Center at
844-299-0879 or [e-mail].
DATED PROOF OF PURCHASE, MODEL # AND SERIAL #
REQUIRED FOR WARRANTY SERVICE