Black & Decker KA1000 User manual

KA1000

2
English (Original instructions) 5
Deutsch (Übersetzung der Originalanleitung) 10
Français (Traduction des instructions d'origine) 16
Italiano (Traduzione delle istruzioni originali) 21
Nederlands (Vertaling van de originele instructies) 26
Español (Traducción de las instrucciones originales) 31
Português (Tradução das instruções originais) 37
Svenska (Översättning av de ursprungliga anvisningarna) 43
Norsk (Oversettelse av de opprinnelige instruksjonene) 48
Dansk (Oversættelse af de originale instruktioner) 53
Suomi (Alkuperäisten ohjeiden käännös) 58
Ελληνικά (Μετάφρασητωναρχικώνοδηγιών) 63

3
C
D
B
A
E

4
F1 F2
GH

5
ENGLISH
Intended use
Your Black & Decker sander has been designed for sanding
and polishing wood, metal, plastics and painted surfaces.
This tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
suchasinthepresenceofammableliquids,gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
inuenceofdrugs,alcoholormedication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Usepersonalprotectiveequipment.Alwaysweareye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other
condition that may affect the power tools operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.

6
ENGLISH
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Haveyourpowertoolservicedbyaqualiedrepair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@ Warning! Additional safety warnings for sanders
uHold the power tool by insulated gripping surfaces,
because the sanding belt / sanding base may contact
its own cord. Cutting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
uUse clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
uWarning! Contact with or inhalation of dusts arising from
sanding applications may endanger the health of the
operator and possible bystanders. Wear a dust mask
specically designed for protection against dust and fumes
and ensure that persons within or entering the work area
are also protected.
uThoroughly remove all dust after sanding.
uTake special care when sanding paint which is possibly
lead based or when sanding some woods and metal which
may produce toxic dust:
- Do not let children or pregnant women enter the work
area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
uThis tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
uThe intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.
Safety of others
uThis appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving
parts.
uInjuries caused when changing any parts, blades or
accessories.
uInjuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.

7
ENGLISH
Labels on tool
The following pictograms are shown on the tool:
:Warning! To reduce the risk of injury, the user must read the instruction manual.
Electrical safety
#This tool is double insulated; therefore no earth wire is required. Always check that the power supply
corresponds to the voltage on the rating plate.
uIf the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust cassette
3. Base
4. Tip holder
5. Sanding base tip
6. Finger attachment
7. Prole attachment
8. Screw
9. Sanding proles
In addition, this tool is supplied with some or all of the
following accessories:
Accessories
The accessories supplied with your sander depend upon the
model that you have purchased. All the accessories listed
below are available in our Piranha® range. If you require an
accessory that is listed below but is not supplied with your
sander please visit our website at www.blackanddecker.eu.
Item Description
Detailnger.
For small hard-to-reach areas. The detail
nger can be used for light sanding and
for sanding into corners.
Sandingproleattachment.
An attachment to hold the various
proles listed below.
Item Description
Concavecurvedsandingprole.
For detailed sanding to suit this shape.
Convexcurvedsandingprole.
For detailed sanding to suit this shape.
Pointedcurvedsandingprole.
For detailed sanding to suit this shape.
240 grit large detail sanding sheet
with two replacement tips.
For a ne nish for large detail sanding.
120 grit large detail sanding sheet
with two replacement tips.
For a medium nish for large detail
sanding.
60 grit large detail sanding sheet with
two replacement tips.
For a coarse nish for large detail
sanding.
High-glosslargedetailnishsheet
(grey) with two replacement tips.
For applying polish.
Cleaning sheet (red) for wood or metal
with two replacement tips.
For cleaning or polishing tasks on wood
or metal.
120gritdetailedngersandingsheet.
For a medium nish for detailed sanding.

8
ENGLISH
Item Description
120gritprolesandingsheet.
For a medium nish for prole sanding.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fittingsandingsheets(g.A&B)
uDetach the two additional diamond-shaped tips (10) from
the sanding sheet (11).
uHold the tool with the sanding base facing upwards.
uPlace the sanding sheet (11) onto the sanding base,
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (10) can be reversed and replaced
when worn.
uWhen the front part of the tip is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
uWhen the whole tip is worn, remove it from the sanding
base and t a new tip.
u The polishing foam and pads (12) can be tted the same
way as the sanding sheets.
For optimal dust collection, ensure the correct type of sanding
paper is used.
Tipofthesandingbase(g.C)
When the sanding base tip (5) or tip holder (4) is worn, it can
be reversed or replaced. Spare parts are available from your
Black & Decker dealer.
uRemove the screw (8).
uReverse or replace the worn part.
uFit and tighten the screw.
Fingerattachment(g.D)
The nger attachment is used for ne detail sanding.
uRemove the screw (8).
uRemove the diamond-shaped tip holder (4) from the
sanding base.
u Fit the nger attachment (6) onto the sanding base.
uFit and tighten the screw.
u Fit the appropriate sanding sheet onto the nger
attachment.
Proleattachment(g.E)
The prole attachment is used for contour sanding.
uRemove the screw (8).
uRemove the diamond-shaped tip holder (4) from the
sanding base.
u Fit the prole attachment (7) onto the sanding base.
uFit and tighten the screw.
Fittingandremovingasandingprole(g.F1&F2)
u Choose the sanding prole most suitable for your
application.
u Place one end of the sanding prole (9) into the recess at
the front end of the prole holder (7).
u Push the other end of the sanding prole until it clicks into
place.
u To remove the sanding prole, push it forward and pull the
rear end out of the prole holder (g. F2).
Fittingasandingsheetontoasandingprole(g.G)
u Align the sanding sheet with the sanding prole (9).
u Press the sanding sheet onto the sanding prole, making
sure that the sanding sheet follows the shape of the prole.
Fittingandremovingthedustcassette(g.H)
uSlide the dust cassette (2) onto the tool and make sure
that it is securely located.
uTo remove the dust casette, pull it to the rear and off the
tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u To switch the tool on, set the on/off switch (1) to position I.
u To switch the tool off, set the on/off switch to position O.
Emptyingthedustcassette(g.H)
The dust cassette should be emptied every 10 minutes of use.
uWhile holding the tool, pull the dust cassette (2) to the rear
and off the tool.
uRemove the cassette door (13).
uShake the door (13) and dust cassette (2) to empty the
contents.
u Ret the door (13) and dust cassette (2) onto the tool.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.

9
ENGLISH
Warning! Before performing any maintenance, switch off and
unplug the tool.
uRegularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Mainsplugreplacement(U.K.&Irelandonly)
If a new mains plug needs to be tted:
uSafely dispose of the old plug.
uConnect the brown lead to the live terminal in the new plug.
uConnect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
ZSeparate collection. This product must not be disposed of with normal household waste.
Should you nd one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
zSeparate collection of used products and packaging allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker ofce at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
KA1000 Type 1
Input voltage VAC 230
Power input W 55
No-load speed min-1 12,000
Weight kg 0.91
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 74.5 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 85.5 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to
EN 60745:
Vibration emission value (ah) 5.1 m/s2,
uncertainty (K) 1.5 m/s2
EC declaration of conformity
MACHINERY DIRECTIVE
%
KA1000
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-4
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
le and makes this declaration on behalf of Black & Decker.
_Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
18/04/2012

10
ENGLISH
Guarantee
Black & Decker is condent of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
uThe product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
uThe product has sustained damage through foreign
objects, substances or accidents;
uRepairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker ofce at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
products is available at www.blackanddecker.co.uk