Unior 1510 User manual

art. 1510
WARNING:
* always read the instruction before using power tools
* always wear safety googles
* wear hearing protection
OPERATING INSTRUCTION
1. Warning
1.1 Air pressure
The air pressure must be restricted at or less than maximum presure 90
psi (6.2 bar), do not exceed it.
1.2 Air line
Use an air hose between the compressor and the tool. The corresponding
hose internal diameter is recommended in the attached table in the data
sheet. Compressed air is cooled and its water content separated as soon as
the air leaves the compressor. However some of the water is condensed in
the piping, and can enter the tool mechanism and cause damage. An air filter
and on oiler should be installed between the compressor and the tool. Use a
recommended compressor in the date sheet or larger for each tool.
Code Air inlet Pad ø thread Stroke Free speed Inner - Hose Max. Air pressure Air consumption Vibration (m/s2) Weight
617733 1/4" 150 - 5/16" 2,5 mm 10000 RPM 8 mm 6,2 bar 368 l/min <2,5 1186 g
617713 1/4" 150 - 5/16" 5 mm 10000 RPM 8 mm 6,2 bar 368 l/min <2,5 1186 g
1.3 Air hose
Clean the hose with a blast of compressed air before connecting
the hose to air tool. This will prevent both moisture and dust within
the hose from entering the tool an causing possible rust or
malfunction. To compensate for unusually long hose (over 25ft)
the line pressure should be increased accordingly.
1.4 Approved eye protection, mask, hearing protection and gloves
shall be worn when operate this tools.
1.5 The working place shall be ventilated.
1.6 Release the on-off device in case of air supply failure.
1.7 Release the start and stop switch in case of a failure of energy
supply.
1.8 Use only a lubricant recommended by the manufacturer.
Pneumatic sander

2.3 Adjusting central vacuum
When turning this button, you can adjust central
vacuum adjustment.
3. Maintenance
3.1 Lubrication
Before connecting the hose, apply 4 to 5 drops of
#60 spindle oil at the inlet. Use of a thicker oil can
lead to reduced performance or malfunction. Also
oil every 3 to 4 hours of operation.
3.2 Storage
Avoid storing the tool in a location subjected to
high humidity. If the tool is left as it is used, the
residual moisture inside the tool can cause rust.
Before storing and after operation, oil the tool at
the air inlet with spindle oil and run it for a short
time.
3.3 Ordering service part
For further operational and handling information or
for replacement of parts and components contact
the outlet from where you purchased the tool or
the service division of your company.
Tool
Leader hose Oil here daily Air hose Nipple
Coupler Oiler
Filter
2. Operation method
2.1 On-off switch
The on-off switch is on the outside of the grip. It
is a "hold-to-run" type. This tool stops rotation in
a few seconds after releasing the lever. For the
sake of safety, please ensure it has completely
stopped before touching.
2.2 Speed adjuster
You can adjust the speed by rotation the knob.
Speed is indicated by letters H and L. H for high
speed and L for low speed.
WARNING:
1. The tool should not be used in potentially explosive atmospheres.
2. Disconnect the air hose before changing or adjusting anything.
3. Prevent loose clothes, long hair etc from coming into contact with the revolving spindle,
as this could cause injury.
4. Excessive high air pressure that exceeds the recommended maximum pressure may cause
injuries to the user.
5. Keep your body in well balanced position and always wear gloves to reduce the risk of
becoming trapped due to torque between handle and work piece.
6. Prolonged exposure to vibration can cause injury.
7. Slip/ trip/ fall is a major reason of serious injury. Beware of excess hose left on the
workplace floor.
8. Wearing correct breathing protection could avoid inhaling dust or debris from work process
that can be harmful to your health.

EC Dec aration of Conformity
Unior d.d.
Kovaška cesta 10, 3214 Zreče, SLOVENI A
Declares under its own responsibility that the following product,
Artic e 1510 - Pneumatic sander
is in conformity with essential safety and health requirements of council Directive
98/37/EEC /june 1998, and folowing provisions of the harmonized standards
mentioned below: prEN 792/ EN 292-1/ EN 292-2/ EN 28662/ DIN 45635-1/ DIN
45635-20/ ISO 8862.
Zreče, December 2006
Gorazd Korošec, President
Name and signature of the authorized person
№ Code Description Qty.
1510.1 617934 Motor housing 1
1510.2 617935 Nut housing 2
1510.3 617936 Housing cover 1
1510.4 617937 Reverse valve 1
1510.5 617938 Muffler insert 1
1510.6 617939 O-Ring 1
1510.7 617940 Pin 1
1510.8 617941 Air regulator 1
1510.9 617942 Valve bushing 1
1510.10 617943 O-Ring 1
1510.11 617944 O-Ring 1
1510.12 617945 Valve pin 1
1510.13 617946 Pin 1
1510.14 617947 Suction tube 1
Spare parts:
Warranty:
Unior d.d. offers one year free charge service warranty to products supplied
by Unior d.d. and authorized dealers.
All products are warranted under following conditions:
* one year from the date of purchase for tools with Unior brand name.
* the free charge service only applies to defects in material and
workmanship. The guarantee becomes invalid if the tool has been
improperly used or has been repaired using non genuine spare parts
and/or has been modified or repaired by someone other then UNIOR d.d.
authorized service representatives.
1510.12 617945 Valve pin 1
1510.13 617946 Pin 1
1510.14 617947 Suction tube 1
1510.15 617948 Pad cover 1
1510.16 617949 Trigger 1
1510.17 617950 Pin 1
1510.18 617951 Muffler insert 1
1510.19 617952 Throttle valve seat 1
1510.20 617953 Throttle gate 1
1510.21 617954 Pin 1
1510.22 617955 Throttle valve spring 1
1510.23 617956 Air inlet 1
1510.24 617957 Muffler body 1
1510.25 617958 Muffler insert 2
1510.26 617959 Cover 1
1510.27 617960 Vacuum adapter 1
1510.28 617961 O-Ring 1
1510.29 617962 Hose adapter 1
1510.30 617963 Snap ring 1
1510.31 617964 End plate gasket 1
1510.32 617965 Pin 1
1510.33 617966 Bearing 1
1510.34 617967 Rear end plate 1
1510.35 617968 Rotor 1
1510.36 617969 Rotor blade 5
1510.37 617970 Cylinder 1
1510.38 617971 Front end plate 1
1510.39 617972 Bearing 1
1510.40 617973 Key 1
1510.41 617974 Crank shaft (2,5mm) for 617733 1
1510.42 617975 Crank shaft (5mm) for 617713 1
1510.43 617976 Snap ring 1
1510.44 617977 Bearing 1
1510.45 617978 Bearing seal 1
1510.46 617979 Bearing shield 1
1510.47 617980 Oil seal 1
1510.48 617981 Random shaft 1
1510.49 617982 Retaining ring 1
1510.50 617983 O-Ring 1
1510.51 617984 Cap sealing ring 1
1510.52 617985 6" sander pad (Select) 1
1510.53 617986 Wrench 1
1510.54 617987 Protective casing 1
1510.55 617988 Suction casing (Select) 1
1510.56 617989 Dirt pocket (Select) 1