Black Widow BWS 1000 Series User manual

INSTRUCTION
MANUAL
IMPORTANT ___
READ THIS INSTRUCTION MANUAL THOROUGHLY! To avoid instal¬
lation problems, please read ail contents of this instruction manual. Do¬
ing so will prevent needless errors in wiring and will aid you in making
this a trouble-free installation!
INTRODUCTION ______
Congratulations! You have just purchased the BWS-SERIES 1000,
Black Widow Remote Vehicle Security System alarm. Below is a de¬
scription of your alarm and how it works.
TRANSMITTER
Your remote controlled Black Widow transmitter is used to arm and dis¬
arm your alarm system. An audible chirp (single when arming/double
when disarming) will be heard when button is depressed.
Your transmitter is powered by a small 12 volt battery which has an es¬
timated life of one to two years. This is the same kind of battery that is
used in some cigarette lighters. Failure of the small red light (L.E.D.) to

come on when the transmitter is activated is a probable indication that
your battery needs replacing.
The panic feature of your alarm system may be activated by pressing
and holding the transmitter for 3 seconds. The siren will sound until the
transmitter button is pressed again.
SIREN/RECEIVER
The most important feature of the Black Widow alarm is its ability to be
armed and disarmed from outside the vehicle. This eliminates the need
for any delay in entry.
When the Black Widow alarm is set off, the siren will sound for 45-60
seconds. Following that, the alarm will automatically reset and continue
to monitor all entries. The built-in memory of the BWS-1000 allows the
owner to know if his car has been tampered with.
The system will not respond to any entry within the first ten seconds of
being armed. This prevents any false triggering of the alarm stemming
from the chirping sound of the siren.
INSTALLATION INSTRUCTIONS _
NOTE: Before mounting the alarm, note the serial and code numbers
and write them in the space provided below. You will need
these numbers to order replacement parts.
SERIAL NUMBER CODE NUMBER
1) MOUNT SIREN/RECEIVER
Mount siren in engine compartment tilted downward to prevent water
build-up. Keep away from extreme sources of heat. For maximum sound
dispersion, mount siren in a position that will provide a direct path to
the ground.
2) SHOCK SENSOR
Turn the adjustment screw clockwise all the way, then back off slowly
until vehicle can take a solid slap to the body to trigger the sensor.
NOTE: Excess shock sensitivity is the #1 cause of false alarms!
3) MOUNT L.E.D.
Extra flashing L.E.D.’s may be connected if desired. Mount and secure
LED. so that it is visible such as on dashboard or rim of door.

TERMINALS/WIRING
# COLOR FUNCTION
NOTES:
1) Grey Accessories Pulsing ground output. For connection to Ignition
Kill, L.E.D.’s, Power Door Locks, Trunk Release, etc.
2) Blue
3) Black
4) Red
5) Brown
Loop
Sensors, Negative trigger input. Connect this wire to Glass
Pin Switches Sensor, Mass Sensor and/or Negative Door Pin
Switches.
Ground Black wire oh molex. Connect to a clean, solid chassis
ground. Note: The long black wire from the Siren/Re¬
ceiver Module is for the Antenna Lead. Do not ground
this wire!
+12V Main Power. Connect to Battery {+) with 5 Amp fuse
at Battery end of wire. On some vehicles with small or
single bulb interior lights, or if the Battery is located
in the trunk, it may be necessary to connect this wire
to the inlet {unfused) side of the fuse box to provide
reliable current sensing.
Current Cut to defeat current sensing if necessary.
Sensing
OPTIONAL ITEMS
The following items can be ordered as additional features for your alarm.
See your dealer.
BWS-500 BATTERY BACK-UP
BWS-410 AUDIBLE BEEPER
BWS-390 LEATHER
TRANSMITTER CASE
BWS-350 FLASHING CIRCUIT,
BWS-340 POWER DOOR
LOCK MODULE
BWS-200
BWS-A-280
MAS-2
BWS-SS-057
SPDT RELAY
BRS-007
GLASS SENSOR
360°
SHOCK SENSOR
MASS SENSOR
MOTION SENSOR
RELAY SOCKET

SPECIFICATIONS
POWER SUPPLY.
TRANSMITTER RANGE.
DIGITAL CODE.
MAX CURRENT DRAW.
NEGATIVE OUTPUT.
ENTRY DELAY.,.,..
CURRENT SENSING REQUIREMENT
AUTOMATIC RESET...
TRIGGERS.
..12 Volts Neg. Ground
.Approx: Up to 100 Feet
.,. Pre-Coded/1 of 20,000 avail.
No more than 15 mA (Disarmed)
.1 Amp Constant (Armed)
....... 0 seconds
.-.6 of a Volt
...60 Seconds
.Negative Existing Pins,
Auxiliary Grounding Pins, Grounding Sensors
SIREN POWER.......120 dB, 20 watts
R.F. CONTROL.310 mHz
LIMITED LIFETIME WARRANTY
DAVID LEVY CO., INC., or its agents will, within one (1) year from date
of sale to you, repair or replace said product or any part thereof, at the
option of DAVID LEW CO., INC. or its agents, if said product or part is
found to be defective in workmanship or materials when properly con¬
nected and operating on specified power requirements.
Obligations of DAVID LEW CO'., INC. or its agents toward this warran¬
ty, do not apply when said product is damaged due to unreasonable or
unintended use, used in commercial or industrial operations, not reason¬
ably maintained, factory seal is broken by anyone other than DAVID
LEW CO., INC . or an authorized repair facility, or damaged while in
consumer possession.
DAVID LEW CO., INC. or its agents will not assume any labor costs
for the removal and re-installation of any product found to be defective
or for the cost of transportation to DAVID LEW CO., INC. or its agents.
Such costs are the responsibility of purchaser.
This warranty is not transferable and extends only to the original pur¬
chaser. This warranty does not cover damage to accessories used in
connection with the product or any damage to products resulting from
alteration, improper installation, misuse or abuse, or acts of God.
Copyright 1991. DAVID LEVY CO., INC.
DLP0191275