MOUNTING A NYLON HOLSTER OR ACCESSORY:
WARNING! WHEN MOUNTING A HOLSTER, NEVER HAVE A FIREARM IN THE HOLSTER.
ALWAYS REMOVE, UNLOAD AND SECURE ANY FIREARM PRIOR TO PLACING A HOLSTER ON THE
MOUNTING PLATFORM.
1. Remove the two threaded twist knobs.
2. Lift up remove the mounting plate from its interlocking pocket position.
3. Place the mounting plate through the belt loop of the holster or accessory.
4. With the holster or accessory attached, place the interlocking end of the mounting plate into the
interlock pocket of the mounting disk.
5. Line up the holes and screw the two threaded twist knobs into place to secure the mounting plate
and holster or accessory to the mounting disk. (Note: Once your holster or accessory is mounted,
you may need to adjust the positioning of the disk. See Adjusting the Mounting Disk.)
MOUNTING A SERPA®CQC®HOLSTER OR SERPA QUICK DISCONNECT SYSTEM ADAPTER:
WARNING! WHEN MOUNTING A HOLSTER, NEVER HAVE A FIREARM IN THE HOLSTER.
ALWAYS REMOVE, UNLOAD AND SECURE ANY FIREARM PRIOR TO PLACING A HOLSTER ON THE
MOUNTING PLATFORM.
1.Remove the two threaded twist knobs.
2.Lift up and remove the mounting plate from its interlocking pocket position.
3.Store the threaded twist knobs and mounting plate in a safe place.
4.A) If mounting an injection-molded holster, remove the belt loop or paddle attachment per the
manufacturer instructions and store the belt or paddle attachment in a safe place. B) If mounting
a Quick Disconnect System Adapter, be sure any holster and/or desired Quick Disconnect System
Adapter has been removed and is ready for mounting.
5.A) If mounting an injection-molded holster, align the holes of the molded disk to the desired ride/
cant adjustment height of the holster and secure it using the screws provided with the holster. B)
If mounting a Quick Disconnect System Adapter, align the holes of the molded disk to the desired
holes on the adapter and secure using the screws provided with the adapter. (Note: Once your
item is mounted, you may need to adjust the positioning of the disk. See Adjusting the Mounting
Disk Angle.)
MOUNTING A NYLON HOLSTER OR ACCESSORY:
WARNING! WHEN MOUNTING A HOLSTER, NEVER HAVE A FIREARM IN THE HOLSTER.
ALWAYS REMOVE, UNLOAD AND SECURE ANY FIREARM PRIOR TO PLACING A HOLSTER ON THE
MOUNTING PLATFORM.
1. Remove the two threaded twist knobs.
2. Lift up remove the mounting plate from its interlocking pocket position.
3. Place the mounting plate through the belt loop of the holster or accessory.
4. With the holster or accessory attached, place the interlocking end of the mounting plate into the
interlock pocket of the mounting disk.
5.Line up the holes and screw the two threaded twist knobs into place to secure the mounting plate
and holster or accessory to the mounting disk. (Note: Once your holster or accessory is mounted,
you may need to adjust the positioning of the disk. See Adjusting the Mounting Disk.)
MOUNTING A SERPA®CQC®HOLSTER OR SERPA QUICK DISCONNECT SYSTEM ADAPTER:
WARNING! WHEN MOUNTING A HOLSTER, NEVER HAVE A FIREARM IN THE HOLSTER.
ALWAYS REMOVE, UNLOAD AND SECURE ANY FIREARM PRIOR TO PLACING A HOLSTER ON THE
MOUNTING PLATFORM.
1. Remove the two threaded twist knobs.
2.Lift up and remove the mounting plate from its interlocking pocket position.
3. Store the threaded twist knobs and mounting plate in a safe place.
4. A) If mounting an injection-molded holster, remove the belt loop or paddle attachment per the
manufacturer instructions and store the belt or paddle attachment in a safe place. B) If mounting
a Quick Disconnect System Adapter, be sure any holster and/or desired Quick Disconnect System
Adapter has been removed and is ready for mounting.
5. A) If mounting an injection-molded holster, align the holes of the molded disk to the desired ride/
cant adjustment height of the holster and secure it using the screws provided with the holster. B)
If a Quick Disconnect System Adapter, align the holes of the molded disk to the desired
holes on the adapter and secure using the screws provided with the adapter. (Note: Once your
item is mounted, you may need to adjust the positioning of the disk. See Adjusting the Mounting
Disk Angle.)
BLACKHAWK.com
BLACKHAWK! • Overland Park, KS U.S.A • 1.800.379.1732 • BH416 0615 • PGIM011BO
®
and
mounting
and
BLACKHAWK.com
BLACKHAWK! • Overland Park, KS U.S.A • 1.800.379.1732 • BH416 0615 • PGIM011BO
®
