Blaupunkt AVMC 1.0 User manual

Enjoy it.
Operating and Installation Instructions
ALL-VIEW-MONITORING CAMERA
AVMC 1.0

Safety Notes
This vehicle security system has been manufactured
according to established safety guidelines. However,
dangers may still occur if the safety notes in this manual
is not observed. This manual is intended to familiarize the
user with the reverse camera important functions. Read
this carefully, prior to using the product. Keep this manual
in an easily accessible location. In addition, do observe the
instructions of the devices used in conjunction with this
all-view monitoring camera.
Attentions
•
•
•
•
•
•
•
•
•
•
This manual may be updated from time to time without
any notice. Please visit www.blaupunkt.com/ase for latest
manual.
CAUTIONS
Disclaimer
In no event shall Blaupunkt be liable for any direct,
indirect, punitive, incidental, special consequential
damages to property or life and whatsoever arising out
of or connected with the use or misuse of our products.
USA & CANADA: This product is not intended for sale in
the United States and Canada. If purchased in the U.S. or
Canada, this product is purchased on as-is basis. No
warranty, whether expressed or implied is provided in
the U.S. or Canada.
1
Assign a mounting location that will not obstruct
driver in any circumstances. Or cause injuries to
drives and passengers in case of emergency brake
or accidents.
Ensure all wires are connected properly, and that
the unit is functioning well before tting the unit
into the mount.
Any unauthorized installation, disassembly or
modication may cause malfunction to the unit and
void warranty of the unit.
Always use only the parts that are included with
the units only.
Do not damage vehicle components when drilling
holes for the mount.
Vehicle may dier from the description provided
here. Consult an authorized Blaupunkt dealer or ve-
hicle’s manufacturer if the information provided here
does not t your specic installation requirement.
This unit is applicable for front, rear and side camera
use. Consult an authorized Blaupunkt dealer during
installation.
Unit does not record video.
Avoid automatic car wash or high-pressure water
to prevent water and pressure from damaging the
camera or causing it to fall o.
Do not install this unit near heater outlet.

SPECIFICATION
2
Features
Chip Model
Camera Specications
Eective Pixels
Image Resolution
Maximum Frame Rate
Dynamic Range
Sync System
Signal Noise Ratio
Video Signal
Exposure Control
White Balance
Illumination Min.
Operating Voltage
Power Input Range
Operating Temperature
Accessories
IMX8307(Camera)+NVP2431(Processing)
1/3 inch (6mm)
1297x977=L27MP
1000 TVL
720p HD 60fps
Support Standard Dynamic Range
Internal
≥48dB
1.0Vp-p at 75ohm
Automatic
Automatic
0.001 Lux/F2.0
3.5V~5.5V
3.5V~5.5V
-20~75°C
Front & Rear Camera
4x Extension Cord
(Yellow - 6.5m)/ (Red - 3.9m)/
(Blue - 4.0m)/ (Black - 4.0m)
Hole Saw Rear Camera
Bracket
3M Tape 4x Grommet
Side Camera (Left/ Right)
1x Wire Hardness (0.2m)
4x Tapping Screws
4x Machine Screws

a) Front Camera c) Side Camerab) Rear Camera
3
WIRING DIAGRAM
INSTALLATION LOCATION
HDMI 4G-
4G+
GPS
WIFI
BLACK
Connec
t
YELLOW
RED
BLUE
BLACK
YELLOW
RED
BLUE
FRONT
REAR
LEFT
RIGHT
FRONT
CAMERA
REAR
CAMERA
LEFT SIDE
CAMERA
RIGHT SIDE
CAMERA

1.0
•
•
•
•
•
3.0
•
3.1
3.1.1
3.1.2
2.0
•
•
•
Vehicle Settings
Select to choose your car model
Select to choose your car color
Select to choose your preferred trace
Select to choose your preferred angle mode
Select “Save”to conrm the settings
Calibration
Key in the password“0000” to access the
Calibration Interface
Calibration Template
Auto Sitching (4 Options)
Manual Sitching (2 Options)
View Angle Adjustment
Select the desired viewing angle, then press the
up, down, left or right symbols for proportional,
horizontal, vertical oset adjustment
Select “Reset” to initialise the settings
Select “Save”to conrm the settings
4
FUNCTIONS
AVM UI Interface
1
3
2
1
2
3
4
5

5
FUNCTIONS (AUTO SITCHING)
Requirement for Calibration :
a)
b)
c)
d)
The Placement of Calibration Cloth
a)
b)
The front & rear calibration chessboard cloths should close to the front and rear of the car body to reduce the
blind spots.
When installing the left and right cameras, the front and rear of the car must be on a horizontal line.
Calibration Template
Option 1
a) Calibration Cloth Size :
• Front & Rear : 4.4x1.2m
• Left & Right : 1.6x1.2m
b) Square Dimension : 60x60cm
Option 2
a) Calibration Cloth Size :
• Front & Rear : 4.8x1.2m
• Left & Right : 1.6x1.2m
b) Square Dimension : 1.0x1.0m
Option 3
a) Calibration Cloth Size :
• Front & Rear : 4.4x1.2m
b) Square Dimension : 1.0x1.0m
Option 4
Surrounded by Calibration
Cloth
Installation Tools : 2-4 pcs of measuring tape
Venue : at least 12M (L) x 6M (W) empty space with the relatively at ground (should not on slopes or uneven
ground)
Environment : Daily brightness is most suitable for adjustment, water on the ground will aect the calibration.
Adjustment : During the steps of calibrating marking point, it is advised to have 1-2 people in the car, and the indi-
viduals should not get in and out of the car during calibration process. (The weight of the car will be changed due
to get in and out of the car, which is resulting the car to move up and down and causes the marking points error)
3.1.1 Auto Sitching

6
FUNCTIONS (AUTO SITCHING)
3.
c)
Calibration Process
a)
b)
The front & rear calibration chessboard cloth should be centered and parallel to the front and rear of the car. It is
recommended to use a measuring tape to measure.
The width is the actual width of the car +20cm, and the length of the car is the distance between the front and
rear cloth.
After the calibration chessboard cloth is placed correctly, click on the vehicle parameter and enter the length &
width of the car, camera types, and the chip of the vehicle.
After entering the parameters, click“Start Stitching”, and wait for a few seconds to complete the stitching, then the
result of the stitching will be displayed.
Centralize the chessboard cloth Centralize the chessboard cloth
Length
Width
Front Rear

FUNCTIONS (AUTO SITCHING)
c) When the result of the automatic stitching is not ideal, you can enter the lens correction section, and perform lens
correction on the four cameras of the front, rear, left, and right.
7
Sitching Adjustment
Use the stitching adjustment and the centre point setting to adjust or calibrate the landmark lines, if the landmark
lines are incorrect or staggered.
Adjustment Method
a)
b)
c)
Left or right are curved : Adjust the center point to set the vertical value.
Left and right landmarks are not on a horizontal line : Adjust the center point set the left and right values.
Front and rear landmarks are staggered : Adjust the left rotation, right rotation, left shift and right shift by pressing
stitching adjustment for correction.

8
FUNCTIONS (MANUAL SITCHING)
Calibration Template
Option 1
a) Calibration Cloth Size :
• Front & Rear : 4.8x1.2m
b) Square Dimension : 60x60cm
The Placement of Calibration Cloth & Marking Point Sequence
a) Option 1
Option 2
a) Calibration Cloth Size :
• Front & Rear : 4.8x1.2m
b) Square Dimension : 1.0x1.0m
3.1.2 Manual Sitching
b) Option 2
Car Length
Car Length
Front Rear
Front Rear
Left Right
Left Right
Car
Width
Car
Width
Car Length
Car Width
Measuring
tape
Measuring
tape
Cheeseboard
Cheeseboard

FUNCTIONS
4.1
•
•
•
•
DVR Setting
Auto Record: O/On ( Default: On). The upper left corner of the 360° view interface and the main page interface
will not displays the recording“red dot”when turned the recording switch as “O”.
File Path (Storage Location): USB 2
Segment Size: 1min/ 3 min/ 5 min ( Default: 3 min )
Format the recorder memory card : All of the les will be deleted, if USB ash drive is formatted.
4.0
•
•
•
DVR
Select the prefered video le to enter the playback interface. There is 4 channels camera eld simultaneous
playback in default. Press on the play/pause, previous or next icons on the control menu panel (at bottom) and
fast forward/rewind by dragging the progress bar.
Video les in the lists can be deleted manually. Tick“ “ on the video les that needs to be deleted and click
the“trash bin”icon on the upper right corner to delete. Lock and protect the video les by pressing the “ “
icon on the upper right corner. The locked the video les can be unlocked by ticking the “ “ icon & pressing
the “ “ again.
The system is automatic loop recording when the head unit is turned on and the duration of each recording is
about 3 minutes. It can be set to 1 minute or 5 minute based on the user’s perference.
9

FUNCTIONS
5.0
•
6.0
Image Adjustment
The image brightness, contrast, colours, saturation, sharpness ratio of front & rear view, left and right
view can be adjusted accordingly.
System Settings
10

UI Interface
2D Horizontal
2D Streaming Front View
2D Zoomed In (Front Car Body)
2D Front View
All image are for reference only, actual display mode is subject to the real-time situation
Front, Left & Right Side View
2D Front Angle View
2D Streaming Rear View
2D Zoomed In (Rear Car Body)
11

UI Interface
Left & Right Side View
3D Rear View
3D All-Around View
3D Left Side View
3D Right Side View
12

TROUBLESHOOTING
Problem
Display monitor / car radio does not show surround
view.
Surround view does not show even after restarting
the display monitor/ car radio.
Surround view does not show even though power
supplies of the reverse light or the rear car plate light
is properly connected.
Solution
Restart the display monitor / car radio.
Examine if the power supplies is properly connected.
Examine if the power supply cables is damaged. Repair/
replace if the cables are damaged.
If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt
authorized dealer if problem persist.
13

Designed and engineered by Blaupunkt Competence Centre 1 321 21 001 20 01