Blaupunkt CDC RF6ir User manual

C-RF6ir
6-Disc FM Modulator CD Changer with Infrared
Sensor - For Use With Any FM Vehicle Radio
Changeur de CD a capteur infrarouge
/modulateur FM a 6 disques
.-
Cambiador de Discos Compactos Para 6 Discos
con Sensor lnfrarojo y Modulador de FM Para Uso
con Cualquier Radio FM de Vehiculo
Cambiador CD para 6 discos corn Modulador FM
corn Sensor lnfravermelho para uso coin qualquer
Radio FM de Automovel
@BLAUPUNKT
Bosch Group

Owner’s Record
The model and warranty numbers are located on the rear of the unit. Record the warranty in the space
provided below. Refer to these numbers whenever you call upon your Blaupunkt dealer regarding this
product.
Model No. CDC-RF6ir
Warranty Number
FCC Warning
The equipment has been tested and found to comply with the limits for a Class B device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and, if not installed and used in accordance with instructions, may cause harmful
interference with radio communications. However, there is no guarantee that radio interference will not
occur in particular installation.
l The shielded interface cable recommended in this manual must be used with this equipment in order
to comply with limits for a digital device pursuant to Sub-part B of Part 15 of the FCC rules.
l Because the laser beam used in this compact disc changer is harmful to the eyes, do not attempt to
disassemble the cabinet. Refer servicing to qualified personnel only.
l You are cautioned that any changes or modifications not expressly approved in this manual could
void your warranty and authority to operate this equipment.
l If you have any questions or problems concerning your unit that are not covered in this manual,
please contact your Blaupunkt dealer.
CAUTION
The use of optical instruments with this product will increase eye hazard.
Because the laser beam used in this compact disc changer is harmful to the eyes, do not attempt to
disassemble the cabinet. Refer servicing to qualified personnel only.
Safety Certification
This Compact Disc Player is made and tested to meet exacting safety standards, It meets FCC
requirements and complies with safety performance standards of the U.S. Department of Health and
Human Services.
Staple Your Sales Receipt Here
2

Table of Contents
Before installing and operating this unit, please
read this manual thoroughly and retain it for Antes de instalar y operar esta unidad, por favor
future reference.
lea este manual detenidamente y guardelo para
referencia en el futuro.
English
Owners’s Record .................................................
2
FCC Warning........................................................
2
Features ...............................................................
4
Precautions .......................................................... 4
Before lnstallating and Testing The System..
......
.
Electrical
Connections........................................
.6
Installation
............................................................
7
Specifications ...................................................
.12
Magazine & Compact Discs .............................
.13
Location of Controls ......................................... .14
Operating
Instructions
......................................
.15
Optional Wireless
Fiemoto Control.. .................
.16
Switching to A
Second CD Changer..
...............
Switching to Radio or Cassette
16
.........................
16
Troubleshooting Guide ..................................... .17
Error Codes........................................................
18
Avant d’installer et de faire fonctionner cet
appareil, veuillez lire attentivement ce manuel et
le conserver afin de pouvoir le consulter a
I’avenir si nkcessaire.
lndice
Apuntes del Propietario .................................... .35
Advertencia de
la FCC.. .................................... .35
Caracteristicas .................................................. .36
Precauciones .....................................................
36
Antes de lnstalar y
Probar el Sistema
..............
.36
Conexiones Electricas ...................................... .38
Instalacion .......................................................... 39
Especificaciones
...............................................
.44
Compartimiento de Discos y Discos Compactos......4 5
Ubicacion de 10s Controles ............................... 46
lnstrucciones de Operation
............................. .47
Control
Remoto Inalambrico Optional..
...........
.48
Cambio
a un Segundo Cambiador..
.................. .48
Cambio a Ejecucion de Radio o de Cinta.. ......
.48
Guia de
Detection de Problemas .................... .49
Codigo de Errores
.........
.
....................................
50
Antes de instalar e operar esta unidade, por
favor leia este manual minuciosamente e
guarde-o para futura referencia.
Sommaire
Archive du proprietaire
.....................................
.19
Avertissement de la FCC .................................. .19
Caracteristiques ................................................. 20
Precautions aprendre ...................................... .20
Avant de monter et de tester le systeme ..........20
Raccordements electriques ............................... 22
Installation
.......................................................... 23
Specifications ................................................... .28
Compartiment CD & disques compacts.. .........29
Emplacement des commandes .......................
.30
Mode d’emploi-Fonctionnement g&&al..........3 1
Commande a distance sans fil optionnelle..
.....3 2
Comment passer A un second changeur
de disques compacts
.........................................
32
Comment passer au mode Radio & Cassette..
. ..3 2
Guide de depannage ........................................
.33
Codes d’erreurs ................................................
.34
indice
Registro do
Proprietario
.....................................
51
Avis0 da FCC
....................................................
.51
Caracteristicas ................................................... 52
PrecaucBes ........................................................
52
Antes
de lnstalar e Testar o sistema................. .52
Conexoes Eletricas ............................................
54
Instalacao ...........................................................
55
Especificacdes.. ................................................ .60
Porta-discos e Discos Laser
............................
.61
Localizacao dos Controles ...............................
.62
Instrucoes
de Funcionamento.. ........................ .63
Controle Remoto sem
Fio Optional
.................
.64
Mudando para urn Segundo Cambiador CD..
... .
Mudando para
o Radio e Toca-fitas.. ................ .64
Guia para
Soluc%o de Problemas .................... .65
Mensagens de Erro
........................................... .66
3

Features
Congratulations on your purchase of your Blaupunkt CDC-RF6ir FM Modulator CD Changer. This unit
is designed to convert CD sound into FM signals (89.1 MHz or 88.7 MHz) and play them through any
FM car stereo. This unit features:
For Use With Any Electronically-Tuned FM
Vehicle Radio
Includes:
l Changer
l Wired Remote Control
l FM Modulator
l Disc Magazine
l Cables
l Mounting Hardware
Features Include:
l Disc and Track Select
l Audible Cue/Review
l Pause/Play
l Switchable Output Frequency:
89.1 MHz/88.7 MHz
l Anti-Shock & Vibration Mechanism
Precautions
4 Optional Wireless Remote Control:
l Disc and Track Mix and Repeat
l Disc and Track Scan
n Power Requirement:
l 12 V DC Vehicle Battery
n Compact, Space-Saving Dimensions:
l 25Ox64x178mm
l 9 718 x 2 l/2 x 7 in. (W x H x D)
l Fits in Many Gloveboxes
l Vertical, Horizontal, or 45” Installation
l The use of optical instruments with this product will increase eye hazard.
l Because the laser beam used in this compact disc changer is harmful to the eyes, do not attempt to
disassemble the cabinet. Refer servicing to qualified personnel only.
l This CD Changer is designed to be operated only on +12 volt DC negative ground systems. The unit
cannot be used on +24 volt or positive ground systems.
l If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside the
vehicle, allow the unit to cool off before operating your unit. The unit may not operate correctly in
extremely hot or cold temperatures. The unit is equipped with a built in self protection circuit. When
the temperature reaches a preset level, the protection circuit halts all unit operation. If this should
happen, open a window and allow the car to cool.
l You are cautioned that any changes or modifications not expressly approved in this manual could
void your warranty.
- .
l If you have any questions or problems concerning your unit that are not covered in this manual,
please contact your Blaupunkt dealer.
Before Installation and Testing the System
@I/<?#&*>@! To avoid the aggravation of costly mistakes and serious damage that could make you feel
this way - please carefully follow all of the instructions. You’ll be glad you did!
General Recommendations
l If you’re not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt
installation technician.
l Design and specifications subject to change without notice.
l We recommend making all electrical connections and testing the system before installing the unit.
4

Before Installation and Testing (continued)
Transport Lock SCWWS
The mechanism in the CD changer is “locked” into place during
shipment by three transport screws. Be sure to remove the screws prior
to testing the system and installation.
To keep dust out of the unit, which could cause a malfunction, place the
enclosed seals over the screw holes after the Transport Lock Screws
have been removed.
Reset Button
A Reset Button is located on the front panel of the
Commander and must be activated with a pen tip or other
thin object, as it is recessed to prevent accidental
engagement. Press the Reset Button under the following
circumstances:
1. After connections have been made for initial testing.
2. After installation, when all wiring is completed.
3. If abnormal disc operation is encountered, the Reset
Button should be pressed to clear the system to
return to normaloperation.
4. After disconnecting and reconnecting the car battery, etc.
ID (Identity) Switch for 2nd CD Changer
To connect a second CDC-RF 6 changer, you
must use Blaupunkt’s CDC-RF BRIDGE,
which is sold separately. When an
additional CD changer has been connected
using this unit, the ID switch is used to
indicate the number of each respective
changer unit.
l The ID switch is initially set to “1” when
shipped.
l When only one changer is connected, the
switch should be set to “1”.
l When two changers are connected, one
of the unit’s switches should be set to “2”
using a ballpoint pen or similar fine-tipped
tool.
1
2
CD
I
1st unit
2nd unit (additional changer unit)
Setting the Radio Frequency
.
You must select and test the radio frequency that the changer will use before
you mount the FM Modulator.
Set the radio frequency setting to 89.1 using the switch on the back of the
FM Modulator. Test the operation of the changer. (See page 15) If a clear
signal cannot be obtained on 89.1 MHz, change the position of the
frequency-select switch to 88.7.
The radio sensitivity is slightly reduced when the FM Modulator is connected.

Electrical Connections
Electrical Connections
l Caution: before making connections, disconnect the ground wire terminal of the car battery to avoid
shcrt circuits.
l Use this unit only with negative ground 12 Volt (1 l- 16 Volt) direct current (DC).
l Be sure to use the supplied changer cord. Using a cord other than the one supplied may cause
noise or damage.
l Be sure to connect the changer cord to the FM Modulator before mounting. If you attach the
changer cord to the modulator and the cord projects down toward the back of the modulator,
remove the cord and attach the other end of the cord to the modulator.
Power Connections - To prevent short circuits and@ serious damage:
l Disconnect the vehicle battery’s negative terminal before making connections.
Note - If the changer is to be installed in a car that is equipped with an on-board drive or navigation
computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory
may be lost. Under these conditions, use extra caution to avoid causing a short circuit during
installation.
l Connect leads according to the wiring diagram.
l Connect the yellow lead to a constant source of power which has passed through the vehicle’s fuse unit.
l Connect the red power input lead only after the other leads are connected. And be sure to connect it
to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the
accessory position or on position.
l Connect the black lead to a grounded metal part of the vehicle. We recommend grounding all audio
system black ground leads (head unit, external amplifier, etc.) to a common point.
Modulator
output
,
Radio Antenna
Input (in back)
FM Radio ’
(6 pin)
-
Yellow
Fuse 5A To Battery
t 0
Ip
DIN Connection Cord (6
pin)
Commander 11
CD Changer
6

Installation
.
Recommendations
l Carefully choose the mounting location so that the unit won’t interfere with normal driving.
l Avoid installing the unit it a place:
-Subject to temperatures exceeding 55 degrees C (131 degrees F) (such as in a car parked in direct
sunlight.)
-Subject to direct sunlight
- Subject to excessive vibration
- Near heat sources (such as heaters and heat ducts)
-Exposed to rain, moisture, excessive dirt and/or dust
l This unit should not be installed in any way except that which is authorized (on its side, on its end, at
a 45” angle or suspended). Installing it with its side facing down or upside down can cause
malfunctioning.
l The fuel tank must not be damaged by the installation.
1-
l The unit should not cover any wires or pipelines.
l The unit (and its installation) should not damage or interfere with access to the spare tire, tools or
other equipment in or under the trunk.
l For a safe and secure installation, be sure to use only the supplied mounting hardware.
l Press the reset button after completing the electrical connections and installation. The reset button is
located on the front of the chassis (See page 5).
l If you have any questions or problems concerning your unit that are not covered in this manual,
please contact your Blaupunkt dealer.
l Be sure to remove the transport screws (See page 5).
*
Anti-Vibration Setting
l This unit can be installed horizontally (to the floor or suspended), vertically, and at a 45” angle.
l Once the installation position has been chosen, set Anti-Vibration Setting Switches on both sides of
the unit using a screwdriver.
l The unit may skip if used with the wrong installation setting.
Type of Installation
Horizontal
Suspended
Vertical
45” angle
Setting
H
H
V
45”
Mounting Hardware
(1)
Bracket (L)
(4)
Tapping Screw
(M5x 12)
(1)
Bracket (R)
(2)
Bracket (B)
(4)
Hexagonal Bolt
(M6 x20)
(4)
Hexagonal Bolt
With Washer
(4)
Nut
(M6)
v
ti
(2)
Tapping Screw
(M3x12)
@q
(1)
DIN 8 Pin Cable
Seal
Double
Sided Tape
7

Horizontal Installation
l Confirm that Anti-Vibration
Switches on both left and
right sides are set to
position H.
l Attach bracket (L) and
bracket (Ft) using the
hexagonal bolts (M5 x 8).
l Attach brackets (L) and (R)
to their respective
brackets (B) using the
hexagonal bolts (M6 x 20)
and the hexagonal nuts
(M6).
0
l Pull back the carpet and determine
where to attach the unit.
l Stick the supplied double-sided tape
0
. Remove the hexagonal nuts and
take off the changer.
to the bottom of the brackets (B) and
peel off the paper backing.
l Affix the unit to the floor by pressing
in place.
CD
A
l Using a knife, cut “x”s in the carpet
directly above the brackets (6) bolts.
l Once more, use the hexagonal nuts
l Return the carpet to its original
Q
to attach the changer on top of the
carpet.
position allowing the bolts to
protrude through.
8

Vertical Installation
onfinn
that Anti-Vibration
Switches on both left and
right sides are set to position V,
l Attach brackets (L) and (R)
using the hexagonal bolts
(M5 x 8).
l Attach brackets (L) and (R) to
their respective brackets (B)
using the hexagonal bolts
(M6 x 20) and the hexagonal
nuts (MS).
l Pull back the carpet and determine
where to attach the unit.
l Stick the supplied double-sided tape
to the bottom of the brackets (B) and
peel off the paper backing.
l Affix the unit to the floor by pressing
in place.
l Once more, use the hexagonal nuts
to
attach the changer on
top of the

45’ Installation
l Confirm that Anti-Vibration
Switches on both left and
right sides are set to
position 45.
l Attach brackets (L) and (R)
using the hexagonal bolts
(M5 x 8).
l Attach brackets (L) and (R)
to their respective
brackets (B) using the
hexagonal bolts (M6 x 20)
and the hexagonal nuts
(M6).
I
I
l Pull back the carpet and determine
where to attach the unit.
l Stick the supplied double-sided tape
to the bottom of the brackets (B) and
peel off the paper backing.
l Affix the unit to the floor by pressing
in place.
0
A
l Using a knife, cut Y’s in the carpet
directly above the brackets (B) bolts.
l Return the carpet to its original
position allowing the bolts to
protrude through.
Q
l Remove the hexagonal nuts and
take off the changer.
e
l Once more, use the hexagonal nuts
to attach the changer on top of the
carpet.
10