BlissLights Spright Move User manual

Manufactured by Blisslights
Phone: [phone]
Fax: [phone]
www.BlissLights.com
[email protected]
Assembled in the United States
Please ONLY use
manufacture
provided transformer
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 2 LASER PRODUCT
Diode Laser
Max. Output <1 mW
Wavelenghts 400 - 700 nm
Manufactured by: www.blisslights.com
BlissLights, Escondido, CA 92029
USER’S GUIDE

Notice 2
Before you begin 3
Parts List 3
Setting up the BlissLight Spright 4
Operating the BlissLights Spright 5
Installation Tips 5
Product Specications 6
Limited Warranty 7
Contents

CAUTION – Use of controls or adjustments or performance of
procedures other than those specied herein may result in hazardous
radiation exposure.
This laser product is certied as a CLASS 2 laser product to the
requirements of the US Federal Laser Product Performance Standard
(FLPPS) contained in the regulations in 21 CFR Subchapter J. Class 2
laser products can be hazardous when directly viewed.
Avoid direct viewing of Class 2 laser energy. For reference the FLPPS
requirements for demonstration laser products like laser pointers are
limited to Class 2 levels of laser energy. This product uses diffractive
optics to scatter the beam energy. This scattering effect causes the
energy concentration to drop below the exposure limits for momentary
or accidental viewing at a relatively short distance from the laser
aperture. As similar with all bright light sources, when you operate this
device in unsupervised general public areas, it is recommended that
up close access to the BlissLight be restricted or prevented.
This laser display device incorporates a Class 2 laser system which,
by itself, may be hazardous. However, this laser display device
incorporates a protective housing and diffractive holographic optics in
the machine design such that there is no exposure or human access
to laser radiation during operation or maintenance above the Class
2 limits. Each individual laser beam power is under 1mw which is less
than a standard laser pointer.
UNDER NO CIRCUMSTANCE shall attempts be made to open the
protective housing or operate the device if the aperture windows are
damaged.
All service to this laser display device requiring the protective housing
to be opened and/ or removed shall be performed by BlissLight service
personnel or their authorized agents. Opening the BlissLight protective
housing voids the warranty.
NO LASERS SHOULD BE POINTED INTO THE SKY WITH 10 NAUTICAL MILES
OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS ESPECIFIC PERIMETER
WE RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO
STRAY BEAMS ARE PROJECTED INTO THE AIR.
CHECK WITH YOUR LOCAL AIRPORT OR COUNTY GUIDELINES FOR
FURTHER INFORMATION.
Notice
2

Thank you for purchasing the BlissLights Spright Move. The BlissLights
Spright Move s a unique light xture that uses new laser and
holographic technology to project thousands of moving pin-points
of light to create a “rey” effect without the need for wind. We
hope you enjoy this incredibly unique lighting experience.
Each unit provides over 900 square feet of coverage which
replaces 6 standard landscape lighting xtures or hundreds of feet
of rope lighting. With an average electrical usage of just 8 Watts in
temperatures above 55F, and 17 Watts in temperatures below 55F,
it is perfect for year-round use.
Before you Begin
Immediately upon receiving the xture: carefully unpack the
carton packaging; check the contents to ensure that all parts are
present and are in good condition. Notify the shipper immediately
and retain packing material for inspection if any parts appear
damaged from shipping or the carton itself shows signs of mishan-
dling. Save the carton and all packing materials. In the event that
the xture must be returned to the factory, it is important that the
xture be returned in the original factory box. Please see parts list
below for box contents.
Parts List:
(1) BlissLights Spright Move (1) Transformer
(1) Stake
3

Setting up the BlissLights Spright Move
**Before operating your Spright Move , please read the “Before you Begin” section
and “Notice” section of this user guide.**
STEP 1: First locate the 2-prong plug connected to the cable
exiting the BlissLights Spright Move head. Plug this end into the
matching hole on the end of the 12V Manufacture provided
transformer. Screw the cap on to complete the water tight seal.
Next plug the standard 3-prong plug on the other end of the
transformer into an outdoor/Indoor outlet.
STEP 2: Stake the BlissLights Spright Move into the desired location.
Do not use xture head to stake light into the ground, grasp by
stake only.
4

Operating the BlissLights Spright
The BlissLights Spright Move operates in temperatures of -15o F to
90o F. There may be a slight delay if operating in temperatures
below 55 o F. Please allow up to 10 minutes for light to warm up
and reach its full projection.
Installation Tips
• For scheduled or nighttime-only operation, use with a timer. Do
not connect the light to a dimmer pack, it will damage the light.
Use with manufacture provided transformer only.
• The darker the area the light is being used in, the brighter the
projection. Try to stay away from areas with street lights or other
bright lights.
• If you are going to hang the BlissLights Spright Move, it is
recommended that, for safety purposes, your lights are properly
mounted using a suitable hanging clip and safety cable.
• The BlissLights Spright Move will cover an area of about 30’ X
30’ for every 10 feet away from surface (equivalent to the size of
about 2 two-car garages).
• For more tips and suggestions on how to use and position your
BlissLights, please visit www.blisslights.com
3 feet
1 foot
3 feet of coverage for every 1 foot of throw
5

Product Specications
For more tips and ideas visit www.blisslights.com where you can
also learn more about other Blisslights products and accessories.
BlissLights Clip BlissLights Timer
BlissLights
Garden Accent Light
16-color user selctable
Laser Classification Class 2
Maximum Laser Power
(Single Beam) Less than 1 mw
Laser Wavelength
Laser Optics Single source holographic optical element
Power Consumption Up to 17 Watts
Power Input
Operation Indoor / Outdoor
Operating Temperature -15º F to 90º F
Projection Coverage 30ft. X 30ft.
Maintenance Maintenance Free
Dimensions
Warranty
BlissLights Spright Move
110/120V
(when used with manufacturer provided transformer)
Limited 1 Year
532nm Green - 455nm Blue
14”H x 5.62”L x 4”W
6

LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in materials and workmanship for a period of
one (1) year from date of purchase. This warranty applies only to the original consumer purchaser and only
to products used in normal use and service. If this product is found to be defective, the manufacturer’s only
obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s
discretion, provided that the product has not been damaged through misuse, abuse, accident, modica-
tions, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to have
been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the
product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, neg-
ligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This
warranty shall not apply to the nish on any portion of the product, such as surface and/or weathering, as this
is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty,
whether expressed or implied, of tness for a particular purpose, other than the warranty contained herein. The
manufacturer specically disclaims any liability and shall not be liable for any consequential or incidental loss
of damage, including any labor/expense costs involved in the replacement or repair of said product. Please
contact BlissLights at [email protected], or (626) 709- 3319.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Owner Registration Card
Please ll out, cut along dashed line, afx proper postage and return this Owner
registration card within 10 days to insure that your new BlissLightsis covered by
the limited warranty. You can also go to www.blisslights.com and ll out your
registration card online.
Purchaser’s Name ____________________________________________
Address ____________________________________________________
State __________________________ Zip_________________________
Email: _____________________________________________________
BlissLights Product: ________________ Purchase Date: _____________
Where Purchased (Store Name) _________________________________
Where will the BlissLight be used: ______________________________
If commercial institution, what type of business?
__Restaurant __Bar __Store __Ofce __Other
If home installation, where?
__Walkway __Patio __Garden Area __Porch __Other
Model/UPC Number:_______________________
7