BlissLights BlissLights-50 User manual

Manufactured by Blisslights
Phone: [phone]
Fax: [phone]
www.BlissLights.com
[email protected]
MADE IN USA
Please ONLY use
manufacture
provided transformer
USER’S GUIDE
BlissLights-50


Notice 1
Before you Begin 2
Part List 2
Setting up the BlissLights-50 3
Operating the BlissLights-50 3
Product Specications 4
Limited Warranty 5
Contents

CAUTION – Use of controls or adjustments or performance of
procedures other than those specied herein may result in hazardous
radiation exposure.
This laser product is certied as a CLASS 3R laser product to the
requirements of the US Federal Laser Product Performance Standard
(FLPPS) contained in the regulations in 21 CFR Subchapter J. Class 3R
laser products can be hazardous when directly viewed.
Avoid direct viewing of Class 3R laser energy. For reference the FLPPS
requirements for demonstration laser products like laser pointers are
limited to Class 3R levels of laser energy. This product uses diffractive
optics to scatter the beam energy. This scattering effect causes the
energy concentration to drop below the exposure limits for momentary
or accidental viewing at a relatively short distance from the laser
aperture. As similar with all bright light sources, when you operate this
device in unsupervised general public areas, it is recommended that
up close access to the Blisslights be restricted or prevented.
This laser display device incorporates a Class 3R laser system which,
by itself, may be hazardous. However, this laser display device
incorporates a protective housing and diffractive holographic optics in
the machine design such that there is no exposure or human access
to laser radiation during operation or maintenance above the Class 3R
limits. Each individual laser beam power is under 50mw which is less
than a standard laser pointer.
UNDER NO CIRCUMSTANCE shall attempts be made to open the
protective housing or operate the device if the aperture windows are
damaged.
All service to this laser display device requiring the protective housing
to be opened and/ or removed shall be performed by Blisslights service
personnel or their authorized agents. Opening the BlissLights protective
housing voids the warranty.
NO LASERS SHOULD BE POINTED INTO THE SKY WITH 10 NAUTICAL MILES
OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER
WE RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO
STRAY BEAMS ARE PROJECTED INTO THE AIR.
Notice
1

Before you Begin
2
The Blisslight product line creates an enormous Universe of Stars that
constantly moves and a transforming nebula cloud. Our products offer
low noise-fan less operation, rugged construction, multi-position mounting
system, and plug and play functionality.
Enormous Universe of Stars.
Fan less – low noise cooling.
Multi-position mounting system.
Rugged Construction.
Plug and Play functionality.
Unpacking Instructions
Immediately upon receiving a xture, carefully unpack the carton, check
the contents to ensure that all parts are present, and have been received
in good condition. Notify the shipper immediately and retain packing
material for inspection if any parts appear damaged from shipping or the
carton itself shows signs of mishandling. Save the carton and all packing
materials. In the event that a xture must be returned to the factory, it is
important that the xture be returned in the original factory box.
Warning! Verify that the power source is 110 VAC. All xtures must be
connected to circuits with a suitable Earth Ground.
Part List
BlissLights-50:
• (1) Blisslights-50
• (1) 6’ AC Power Cord
• User Guide

Setting up the BlissLights-50
**Before operating the BlissLights-50, please read the “Before you Begin”
section and “Notice” section of this user guide.**
3
The Blisslight is a plug and play product and does not require assembly
before operation. Plug in the supplied power transformer or power cord,
position the power switch to “ON”. That’s it.
Operating the Blisslights-50
Switch on power to the Blisslight, and to ll your environment with a
“Universe of Stars”. Turn the Brightness knob located at the back of the
Blisslight to control the brightness of the “Nebula” cloud.
Operate in temperatures of 65F to 86F
Note: This product is design for indoor use only.
Do not connect the device to a dimmer pack.
If you are going to hang the Blisslight, it is recommended that, for safety
purposes, your lighting effect are properly mounted using a suitable hang-
ing clamp and safety cable.
For Warranty issues please email BlissLights at [email protected] or
call [phone].

Product Specications
4

Blisslights-50
Laser Classification
FLPPS Class 3R
Maximum Laser Power
(Single Beam) Less than 5 mw
Laser Wavelength
532 nm
455 nm - Blue
Laser MTBF
More than 7000 hours
Laser Optics Dual source holographic optical
element
LED Power
1 watt
LED Wavelength
455 nm
LED MTBF
More than 100,000 hours
Power Consumption
35 watts
Power Input
110 VAC
Operation
Plug and Play
Operating Temperature Less than 86oF
Projection Coverage
50ft x 50ft
2.5 ft of coverage for every 1 ft of throw
Maintenance
Maintenance Free
UL Listed
Yes
Dimensions
3.5” H x 6.5” W x 9.25” L
Warranty
1 Year

5
LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in materials and workmanship for a period of
one (1) year from date of purchase. This warranty applies only to the original consumer purchaser and only
to products used in normal use and service. If this product is found to be defective, the manufacturer’s only
obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s
discretion, provided that the product has not been damaged through misuse, abuse, accident, modica-
tions, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to have
been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the
product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, neg-
ligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This
warranty shall not apply to the nish on any portion of the product, such as surface and/or weathering, as this
is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty,
whether expressed or implied, of tness for a particular purpose, other than the warranty contained herein. The
manufacturer specically disclaims any liability and shall not be liable for any consequential or incidental loss
of damage, including any labor/expense costs involved in the replacement or repair of said product. Please
contact BlissLights at [email protected], or (626) 709- 3319.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _
Owner Registration Card
Please ll out, cut along dashed line, afx proper postage and return this Owner
registration card within 10 days to insure that your new BlissLightsis covered by
the limited warranty. You can also go to www.blisslights.com and ll out your
registration card online.
Mailing Address: BlissLights, 1155 Industrial Avenue, Escondido, CA 92029
Purchaser’s Name ____________________________________________
Address ____________________________________________________
State __________________________ Zip_________________________
Email: _____________________________________________________
BlissLights Product: ________________ Purchase Date: _____________
Where Purchased (Store Name) _________________________________
Where will the BlissLight be used: ______________________________
If commercial institution, what type of business?
__Restaurant __Bar __Store __Ofce __Other
If home installation, where?
__Walkway __Patio __Garden Area __Porch __Other
Model/UPC Number:_______________________