Blizzard Lighting Atmos FEAR HEX JET User manual

Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Copyright (c) 2015
HeX JET
TM

Page 2
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x AtmosFear™ Hex Jet LED Fog Machine
• 1 x Remote Control
• An Ever-So-Handy Power Cord
• This Lovely User Manual
Getting It Out Of The Box
Congratulations! Your audiences will soon be blown away and erupt with excitement when
they feast their eyes upon the powerful pyrotechnic-like RGBAW+UV colored fog effects of
the mighty AtmosFear™ Hex Jet! Now that you’re the proud owner of a AtmosFear™ Hex
Jet (or hopefully, Hex Jets!), you should carefully unpack the box and check the contents
to ensure that all parts are present and in good condition. If anything looks as if it has
been damaged in transit, notify the shipper immediately and keep the packing material for
inspection. Again, please save the carton and all packing materials. If a xture must be
returned to the factory, it is important that the xture be returned in the original factory
box and packing.
Powering Up!
All xtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the
xture you receive is suitable for your local power supply. See the label on the xture or
refer to the xture’s specications chart for more information. A xture’s listed current
rating is its average current draw under normal conditions. Check the xture or device
carefully to make sure that if a voltage selection switch exists that it is set to the correct
line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your xture may result if the line voltage applied does
not match the voltage indicated on the voltage selector switch. All xtures must
be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, please just visit our website at www.blizzardlighting.com
and open a support ticket. We’ll be happy to help, honest.
Blizzard Lighting
N16 W23390 Stoneridge Dr. Ste E
Waukesha, WI 53188 USA
www.blizzardlighting.com
414-395-8365
Disclaimer: The information and specications contained in this document are subject
to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any
errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the
right to update the existing document or to create a new document to correct any errors
or omissions at any time. You can download the latest version of this document from www.
blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Thomas 1/27/2015 J. Thomas 3/19/2015

Page 3
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
Attention:
To keep your AtmosFear™ Hex Jet in good working order please remember to:
• Use only water-based, non-toxic fog uid.
• Keep the machine clean.
• Turn the power off before adding fog uid.
• Turn the power off when not in use.
And also...
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the
decal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
cord. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please visit our support website at:
www.blizzardlighting.com/tickets.

Page 4
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
2. MEET THE ATMOSFEAR™ HEX JET
MAIN FEATURES:
• RGBAW+UV color mixing via 12x 15W 6-in-1 LEDs
• Strong, upward ejecting 1,500 watt fog machine
• Variable electronic dimming & strobe
• Built-in color & chase macros via DMX
• Built-in automated programs via master/slave
• RGBAW+UV color mixing ability in standalone mode
• IR remote control included
• Built-in timer
• Rugged and well-built (It hits the gym regularly)
• 3-pin male input and 3-pin female output
• IEC power input connector
DMX Quick Reference (10-Channel Mode)
Ch. Value What it does
1 000 <--> 255 Fog Control - On/Off
2 000 <--> 255 Red Intensity (0% <--> 100%)
3 000 <--> 255 Green Intensity (0% <--> 100%)
4 000 <--> 255 Blue Intensity (0% <--> 100%)
5 000 <--> 255 Amber Intensity (0% <--> 100%)
6 000 <--> 255 White Intensity (0% <--> 100%)
7 000 <--> 255 UV Intensity (0% <--> 100%)
8 000 <--> 255 Strobe (slow <--> fast)
9 000 <--> 255 Auto Mode (No Fog) Color Snap (slow <--> fast)
10 000 <--> 255 Auto Mode (No Fog) Color Fade (slow <--> fast)
6-Button Remote Control Features
Ch. What it does
1 Auto - Press to turn on, press again to change the speed (1-10).
2 Color - Press to cycle through its built-in static colors.
3Fade - Press to turn on + adjust the fade speed (1-10).
4 Interval Fog - Press to turn on/off the interval fog timer.
5 Strobe - Press to start strobe, press again for speed (1-10).
6 Cancel (Stop)

Page 5
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
With a at head screwdriver, wedge the
fuse holder out of its housing. Remove the
damaged fuse from its holder and replace
with exact same type fuse. Insert the fuse
holder back in its place and reconnect
power.
Connecting A Bunch of AtmosFear™ Hex Jets
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the units on a serial data link determines the number of units
the data link can support.
Units on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 units on one serial data link without the
use of a DMX optically-isolated splitter may result in deterioration of
the digital DMX signal. The maximum recommended cable-run dis-
tance is 500 meters (1640 ft). The maximum recommended number
of units on a serial data link is 32.
Data/DMX Cabling
To link units together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc-
es. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms

Page 6
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the
xture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers. If you’d like to build your own,
the chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of
the DMX cable to the rst xture’s male
connector (input). Note: It doesn’t matter
which xture address is the rst one
connected. We recommend connecting the
xtures in terms of their proximity to the
controller, rather than connecting the lowest
xture number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.

Page 7
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
the rst xture.
2. Connect the end of the cable coming from
the rst xture which will have a (female) 3 pin
connector to the input connector of the next xture
consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above
to the input of the following xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the rst xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the xtures
that follow may also
require a slave setting.

Page 8
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS
Control Panel Menu Structure:
<FUNC>
Function Value What it does
Dmx512.ADD 001-512 Sets the DMX starting address
Interval_Time 001s-100s Sets the countdown timer between fog
blasts in seconds
Duration_Time 01s-20s Sets the duration time of fog blasts for
each set Interval Time
Color_Mode 01-32 32 Color Modes
Auto_Mode Speed: 01-10 Auto run speed (slow <--> fast)
Strobe_Mode Speed: 01-10 Strobe speed (slow <--> fast)
LED_Dimmer 000%-100% Dimmer
Fade_Mode Speed: 01-10 Fade speed (slow <--> fast)
<UP>
Scrolls through menu items and numbers in ascending order.
<DOWN>
Scrolls through menu items and numbers in descending order.
<TIMER>
Press this button to start the fogger countdown timer. The timer settings are
found in the control panel menu.
Interval Time: Sets the length of time in seconds between fog blasts. The
settings for this are found in the control panel menu by pressing the function
button until the display reads Interval Time. Use the <UP/DOWN> buttons
to choose the number of seconds between blasts of fog anywhere between
1-100 seconds. Press the <FUNC> button to return to the main menu.
Duration Time: You can now set the fog blast duration by pressing the <FUNC>
button repeatedly until the menu display reads Duration Time. Use the <UP/
DOWN> buttons to choose the number of seconds each blast of fog occurs,
anywhere between 1-20 seconds.
<VOLUME>
Press this button to for continual fog. The LEDs will also run its currently set
programs. Press the <VOLUME> button again to abort.
<MANUAL>
Press and hold the <MANUAL> button down for continual fog and full on white
light. Letting go of the button will stop the process.

Page 9
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
5. APPENDIX
A Quick Lesson On DMX
DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common
communications standard used by lighting and related stage equipment.
DMX provides up to 512 control “channels” per data link. Each of these channels was originally
intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting console,
connected to 512 light bulbs. Each slider’s position is sent over the data link as an 8-bit number
having a value between 0 and 255. The value 0 corresponds to the light bulb being completely off
while 255 corresponds to the light bulb being fully on.
DMX data is transmitted at 250,000 bits per second using the RS-485 transmission standard over two
wires. As with microphone cables, a grounded cable shield is used to prevent interference with other
signals.
There are ve pins on a DMX connector: a wire for ground (cable shield), two wires for “Primary”
communication which goes from a DMX source to a DMX receiver, and two wires for a “Secondary”
communication which goes from a DMX receiver back to a DMX source. Generally, the “Secondary”
channel is not used so data ows only from sources to receivers. Hence, most of us are most familiar
with DMX-512 as being employer over typical 3-pin “mic cables,” although this does not conform to
the dened standard.
DMX is connected using a daisy-chain conguration where the source connects to the input of the
rst device, the output of the rst device connects to the input of the next device, and so on. The
standard allows for up to 32 devices on a single DMX link.
Each receiving device typically has a means for setting the “starting channel number” that it will
respond to. For example, if two 6-channel xtures are used, the rst xture might be set to start
at channel 1 so it would respond to DMX channels 1 through 6, and the next xture would be set to
start at channel 7 so it would respond to channels 7 through 12.
Troubleshooting
Symptom Solution
Fixture Auto-
Shut Off
Check the fan in the xture. If it is stopped or moving slower than
normal, the unit may have shut itself off due to high heat. This is to
protect the xture from overheating. Clear the fan of obstructions,
or return the unit for service.
Beam is Dim Check optical system and clean excess dust/grime. Also ensure that
the 220V/110V switch is in the correct position, if applicable.
No Light Output Check to ensure xture is operating under correct mode, IE sound
active/auto/DMX/Etc., if applicable. Contact service for more infor-
mation.
Chase Speed Too
Fast/Slow
Check to ensure proper setup of speed adjustment.
No Power Check fuse, AC cord and circuit for malfunction.
No Response to
Audio
Verify that the xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.
Fixture Not
Responding /
Responding Er-
ratically
Make sure all connectors are seated properly and securely.
Use Only DMX Cables.
Install a Terminator.
Check all cables for defects.
Reset xture(s).

Page 10
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
Keeping Your AtmosFear™ Hex Jet As Good As New
The LED fogger you have received is a rugged, tough piece of professional
equipment, and as long as you take care of it, it will take care of you. That said,
like anything, you’ll need to take care of it if you want it to operate as designed.
You should absolutely keep the xture clean, especially if you are using it in an
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled
drinks.
Cleaning Instructions:
1.) You should follow these instructions after approximately 40 hours of use.
2.) Take off the nozzle before heating the fog machine, and clean the nozzle
with straight vinegar.
3.) To clean the tank, pour in and run a solution of 80% distilled water and 20%
white vinegar through the machine. When empty turn off the machine.
4.) Wait for it to cool down, re-install the nozzle, and you can now add more
uid to prepare for its next use.
Returns (Gasp!)
We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But,
like any complex piece of equipment designed and built by humans, once in a
while, something doesn’t go as planned. If you nd yourself with a xture that
isn’t behaving like a good little xture should, you’ll need to obtain a Return
Authorization (RA).
Don’t worry, this is easy. Just go to our website and open a support ticket at
www.blizzardlighting.com/tickets, and we’ll issue you an RA. Then, you’ll need
to send the unit to us using a trackable, pre-paid freight method. We suggest
using USPS Priority or UPS. Make sure you carefully pack the xture for transit,
and whenever possible, use the original box & packing for shipping.
When returning your xture for service, be sure to include the following:
1.) Your contact information (Name, Address, Phone Number, Email address).
2.) The RA# issued to you
3.) A brief description of the problem/symptoms.
We will, at our discretion, repair or replace the xture. Please remember
that any shipping damage which occurs in transit to us is the customer’s
responsibility, so pack it well!
Shipping Issues
Damage incurred in shipping is the responsibility of the
shipper, and must be reported to the carrier immediately upon
receipt of the items. Claims must be made within seven (7)
days of receipt.

Page 11
AtmosFear™ Hex Jet Manual - Rev. A (c) 2015 Blizzard Lighting, LLC
Tech Specs!
Weight & Dimensions
Length 20 in (510 mm)
Width 14.7 in (375 mm)
Height 9.8 in (250 mm)
Weight 21 lb (9.6 kg)
Power
Operating Voltage AC 110-240VAC, 50/60 Hz
Power Consumption 1,500W, 9.38A
Power Factor .63
Light Source
LED 12* 15-watt RGBAW+UV LEDs
Optical
Beam Angle 25° Beam Angle
Thermal
Max. Operating Temp. 104 degrees F (40 degrees C) ambient
Operation/Capacity/Consumption
Warm-up Time 10 min.
Tank Capacity 2.5L
Output 45,000 cfm
Control
Protocol USITT DMX-512
DMX Channels 10-Channel
Input 3-pin XLR Male
Output 3-pin XLR Female
Other Operating
Modes Standalone, Master/Slave, IR Remote Control
Other Information
Behind every girls sele is approximately 47 nearly identical photos
that just didn’t cut it.
Warranty
2-year limited warranty, does not cover mal-
function caused by damage to LEDs.

Enjoy your product!
Our sincerest thanks for your purchase!
--The team @ Blizzard Lighting