Wali GSDM003-P User manual
INSTALLATION MANUAL
75x75/100x100 27"
MAX
(1-7kg)x3
(2.2-15.4lbs)x3
RATED
GSDM003-P
Triple Monitor Desk Mount
2
Arm
A (x1)
Monitor Arm
B (x1)
VESA Plate
C (x3)
C-Clamp
D (x1)
Pole
E (x1)
Wire Clip
F (x1)
Grommet Base Plate
G (x1)
Support Plate
H (x1)
Anti-skid Pad
I (x1)
Top Screw
J (x3)
M6X16 Bolt
K (x3)
4mm Allen Key
L (x1)
6mm Allen Key
M (x1)
M4X12 Bolt
M-A (x12)
M4X16 Bolt
M-B (x12)
M5x12 Bolt
M-C (x12)
M5x16 Bolt
M-D (x12)
D5 Washer
M-E (x12)
Spacer
M-F (x12)
Supplied Parts List
3
Fit clamp: 0.4”-3.3”
Grommet: 0.4”-1.6“
Step 1
Measure the thickness of your mounting surface or desk
L
L
D
K
E
I
4
Step 2
Option A
Clamp Installation
1. Loosen the bolts on C-clamp Dusing 4mm Allen Key L .
2. Connect Pole E and C-clamp Brace
D1 from the bottom using M6x16 Bolt Kand tighten with 4mm Allen Key L.
Tear off the protective paper and attach Anti-Skid Pad I to the bottom designated position of C-Clamp Brace D1 as
image shown.
DL
D1
D1
EL
K
C-clamp
Brace
C-clamp
I
5
L
0.4”-2”
L
1.8”-3.3”
4. Rotate the hand knob clockwise to fasten for stability.
3.1 For 0.4''- 2'' thick desk
3.2 For 1.8''- 3.3'' thick desk
Loosen the Bolts on the C-Clamp Brace D1 using 4mm Allen Key L . Hang the C-Clamp D2 on the bolts and tighten
using 4mm Allen Key
L.
D1 D2
L
L
Hand Knob
Loosen the screw to release the hand knob using a screwdriver as image shown. Turn over the bracket
and tighten the screw.
Loosen the Bolts on the C-Clamp Brace D1 using 4mm Allen Key L . Hang the C-Clamp D2 on the bolts
and tighten using 4mm Allen Key L .
D1 D2
L
L
E
G
H
0.4”-1.6”
ø 10mm
(ø ")3/8
Desktop with Existing Through-hole.
0.4”-1.6”
6
Mark the position of the hole on your mounting surface.
Drill a 3/8"(10mm) diameter hole at the marked position
through the mounting surface.
4. Place the Grommet Base Plate G and Pole Eto the grommet hole. Insert the hand knob through the center hole
of Support Plate H and desk hole, rotate the hand knob clockwise to fasten for stability.
GE
H
3b.Self-drilled Grommet Hole Installation3a.Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector,
remove it to ensure a flat surface before installing the desk
mount.
0.4”-2.4”
Option B
Grommet Base Installation
I
G
1. Cut the Anti-skid Pad I along the broken line. Tear
off the protective paper and attach Anti-Skid Pad I to
the bottom designated position of Grommet Base
Plate G as the image shown.
2. Loosen the screw to release the hand knob
using a screwdriver as image shown.
(Screwdriver not included )
I
G
Hand knob
I
Step 2
D3
7
Step 3
Step 4
1. Firmly hold the two halves of the spring arm
together and have another person cut off the
cable tie from around the spring arm.
2. Slowly release the pressure on the spring
arm and allow it to gradually stretch to its full
extension.
WARNING: A
M
M
B
F
A
E
Put the Arm Aand Monitor Arm B through the Pole E
, adjust the preferred height and tighten using
6mm Allen Key M
. Attach the Wire Clip
Fto the Pole E.
BE
E
F
M
A
8
Step 5
Step 6
Step 5.1
Step 5.3a
M-D
M-B
M-A
C
J
A
Put the assembled TV/Monitor onto the Arm Aand ensure stability, tighten the VESA plate
using Top Screw J.
A
A
B
J
M4 M5
Only one screw size fits your Monitor
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw diameter (M4 or M5)
to use.
Step 5.2
Select Monitor Screws Select Spacers ( if needed )
Select M4x12 Bolt M-A or M5x12 Bolt M-C
according to your TV/Monitor,connect VESA Plate E
together with D5 Washer M-E into the mounting
holes on the back of TV/Monitor, tighten with
screwdriver.
Select M4x16 BoltM-Bor M5x16 Bolt M-D according
to your TV/Monitor,connect VESA Plate Ctogether
with D5 Washer M-E and Spacer M-F into the
mounting holes on the back of TV/Monitor, tighten
with screwdriver.
Step 5.3b
E
M-C
M-E
M-E
M-F
M-B
M-D
C
CM-A
M-E
9
Step 7
To properly balance the arm with monitors mounted, adjust the spring tension with Allen Key 6mm
M.
First, position and firmly hold the arm horizontally
as shown. Ask for assistance should you require it.
CAUTION:To avoid damage to monitors or
mount, always keep the arm in a horizontal
position while making adjustments.
Again, ask for assistance if required.
CAUTION:
DO NOT over tighten the screws.
M
If the arm rises, turn the adjustment
screw clockwise until it stays in a
horizontal position.
If the arm drops, turn the adjustment
screw counter-clockwise until it stays in
a horizontal position.
10
Step 8
Slide the cable slot covers towards the VESA plate direction to detach it off the arm. Guide the cable
through the cable slot and put the cover back to the arm.
Store the Allen Keys in the Wire Clip .
Note: If the display does not stop
at your desired position, tighten the
screws as shown.
M
11
Step 9 Angle Adjustments
Rotate: Manually adjust rotate angle.
(Rotate 360°)
Swivel: Manually adjust swivel angle.
(swivel -90°/+90°)
Tilt: Adjust the VESA Plate tilt using 6mm Allen
Key M. (Tilt +35°/-35°)
M
M F
L
If you have any questions,please contact us.
We support the technology that brings your home to life.
We offer high quality products, professional customer service,
and extensive technical support.
www.walielectric.com
Other Wali Rack & Stand manuals
