Blomberg DWT14210 User manual

USA
Installation Manual
Dishwasher
FOR MODELS
DWT 14210 NBL00
DWT 14220 NBL00
DWT 14240 NBL00
DWT 15210 NBL00
DWT 15220 NBL00
DWT 15240 NBL00
DWT 15211 NBL00
DWT 15221 NBL00
DWT 15241 NBL00
DWT 34210 NBL00
DWT 34220 NBL00
DWT 34240 NBL00
DWT 34200 NBL00
DWT 35210 NBL00
DWT 35220 NBL00
DWT 35240 NBL00
DWT 35200 NBL00
DWT 36210 NBL00
DWT 36220 NBL00
DWT 36240 NBL00
DWT 36211 NBL00
DWT 36221 NBL00
DWT 36241 NBL00
DWT 36200 NBL00
DWT 36201 NBL00
DWT 37210 NBL00
DWT 37220 NBL00
DWT 37240 NBL00
DWT 37200 NBL00
DWT 14440 ULTRA
DWT 14410 ULTRA
DWT 14420 ULTRA
DWT 34400 ULTRA
DWT 34410 ULTRA
DWT 34420 ULTRA
DWT 34440 ULTRA

Installation Manual For
Dishwasher Models
DWT 15211 NBL00
DWT 15221 NBL00
DWT 15241 NBL00
DWT 14210 NBL00
DWT 14220 NBL00
DWT 14240 NBL00
DWT 15210 NBL00
DWT 15220 NBL00
DWT 15240 NBL00
DWT 34210 NBL00
DWT 34220 NBL00
DWT 34240 NBL00
DWT 34200 NBL00
DWT 35210 NBL00
DWT 35220 NBL00
DWT 35240 NBL00
DWT 35200 NBL00
DWT 36210 NBL00
DWT 36220 NBL00
DWT 36240 NBL00
DWT 36211 NBL00
DWT 36221 NBL00
DWT 36241 NBL00
DWT 36200 NBL00
DWT 36201 NBL00
DWT 37210 NBL00
DWT 37220 NBL00
DWT 37240 NBL00
DWT 37200 NBL00
DWT 34400 ULTRA
DWT 34410 ULTRA
DWT 34420 ULTRA
DWT 34440 ULTRA
DWT 14440 ULTRA
DWT 14410 ULTRA
DWT 14420 ULTRA

Contents
1. IMPORTANT SAFETY INSTRUCTIONS 1
1.1 INSPECT THE DISHWASHER 2
1.2 HOW TO CONTACT US 2
2. TOOLS WHICH MAY BE NEEDED 3
3. MATERIALS WHICH MAY BE NEEDED 3
4. MATERIALS SUPPLIED 4
4.1 PARTS SUPPLIED 4
4.2 MANUAL BAG 4
4.3 DISHWASHER PARTS BAG 1 4
4.4 DISHWASHER PARTS BAG 2 4
4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER 4
5. DISHWASHER SPECIFICATIONS 5
5.1 TECHNICAL FEATURES 5
6. ENCLOSURE PREPARATION 6
6.1 ELECTRICAL PREPARATION 6
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS 7
6.3 ADJUSTING HEIGHT 7
6.4 INSTALLING THE SIDE TRIM STRIPS 8
6.5 PREPARING THE WATER CONNECTION (A) 9
6.6 DRAIN PREPARATION 10
7. PLACEMENT OF DISHWASHER INTO THE OPENING 11
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 11
7.2 READJUSTING FOOT LEVELS 16
7.3 ADJUSTING THE MOVABLE TOE KICK 16
7.4 INSTALLING THE OUTER DOOR 17
8. INSTALLER CHECKLIST 23
9. FINAL INSTRUCTIONS 23
10. SELF HELP HINTS 23
To prevent accidents, which could cause serious injury or death, as well as
machine damage read these instructions before installation and / or use.

1USA
CAUTION
WARNING
ÝNotice
INTRODUCTION
Please read this installation manual
and particularly the safety instructions
completely and carefully. They will save you
time and effort and help to ensure optimum
dishwasher performance.
Be sure to observe all listed warnings and
cautions. Look particularly for the icons with
exclamation marks inside. The information
icon also will provide important references.
WARNING
When installing the dishwasher, follow
basic precautions, including the
following:
• The dishwasher installation must be
performed in accordance with this
installation manual. If you did not receive
an installation manual, order it by
calling 1-800-459-9848 or you may also
download it from our web site at
www.blombergappliances.com
• Installation and repair should be
performed by a qualified installer.
Work by unqualified persons could be
dangerous and may void the warranty.
• Do not operate the appliance if damaged,
malfunctioning, partially disassembled or
if it has missing or broken parts.
• Also follow the safety instructions of the
user manual.
• To reduce the risk of electric shock, fire,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
• Only connect the dishwasher to the
power supply when all installation and
plumbing work is complete.
• If the dishwasher is installed in a location
that experiences freezing temperatures
(e.g. in a vacation home, cabin, etc.),
you must drain all the water from the
dishwasher’s interior. Water system
ruptures that occur as a result of freezing
are not covered by warranty.
• Dishwasher must be secured to adjacent
cabinetry using the brackets provided.
Failure to do this may cause damage to
property or bodily injury.
• Connect to a properly rated, protected
and sized power supply circuit to avoid
electrical overload. The dishwasher is
designed for an electrical supply of 120 V
(volts), 60 Hz (hertz), AC, connected to a
dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breakers
rated for 15 amperes. Electrical supply
conductors shall be a minimum of # 14
AWG copper wire rated at 75 °C (167
°F) or higher. These requirements must
WARNING:
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION:
Indicates a potentially hazardous situation
which, if not avoided, may result in injury.
It may also be used to alert against unsafe
practices.
Notice:
Indicates a potentially hazardous situation
which, if not avoided, may result in damage
to the dishwasher, the table-ware, the
equipment or the environment.
1. IMPORTANT SAFETY
INSTRUCTIONS
In addition to these instructions, the
dishwasher shall be installed:
• In accordance with all local codes or, in
absence of a local code,
• In the United States, with the National
Electric Code,
• In Canada, with the Canadian Electric
Code C22.1-latest edition/Provincial and
Municipal codes and/or local codes.
Notice :
Read these installation instructions
completely before installing and follow
them carefully. Save these installation
instructions and pass them on to any future
user.

2USA
be met to prevent injury and machine
damage. Consult a qualified electrician if
in doubt.
• Do not use any extension cord or
portable outlet device to connect the
dishwasher to a power supply.
• Ensure that any plastic wrappings, bags,
small pieces etc. are disposed of safely
and kept out of the reach of children.
Danger of suffocation!
• Remove the door to the washing
compartment when removing an old
dishwasher from service or discarding it.
Ensure that the appliance presents no
danger to children while being stored for
disposal.
• Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Notice :
• The dishwasher drain hose must be
installed with a drain loop at least 28"
(710mm) off the cabinet floor; otherwise
the dishwasher may not drain properly.
• This dishwasher is intended for
residential use only, and should not be
used in commercial establishments.
• New installation - If the dishwasher is a
new installation, most of the work must
be done before the dishwasher is moved
into place.
• Replacement - If the dishwasher is
replacing another dishwasher, check
the existing dishwasher connections for
compatibility with the new dishwasher,
and replace parts as necessary.
1.1 INSPECT THE DISHWASHER
After unpacking the dishwasher and prior
to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic
damage. Report any damage immediately.
Notice :
• Cosmetic defects must be reported within
10 days of installation.
• Do not discard any bags or items that
come with the original package until
after the entire installation has been
completed.
1.2 HOW TO CONTACT US :
You may either call our Toll Free Number at
1-800-459-9848 or contact us via the web
site at
www.blombergappliances.com
or Contact the Blomberg Distributor for
your State or Province as listed on the
Distributor Contact List provided.

3USA
2. TOOLS WHICH MAY BE NEEDED
3. MATERIALS WHICH MAY BE NEEDED
(Additional materials may be required to comply with local codes)
Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
Electrical Supply Cable - Minimum #14AWG, 2 conductors, 1 ground,
insulated copper conductors.
90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your
water supply line (copper tubing/compression fitting, or braided hose) on
the other leg.
UL listed conduit connector or strain relief.
Teflon tape or other pipe thread compound to seal plumbing connections.
Shut-off valve and fittings appropriate for hot water supply line (copper
tubing/compression fitting, or braided hose).
Silicone
Glue

4USA
x1
x1
a.
b.
d.
e.
f.
g.
h.
c.
x1
x1
x1
x1
x6
x1
x2
x2
j.
k.
l.
m.
o.
p.
s.
v.
u.
7
3/4
(19 ,5mm)
y.
n.
r.
t.
x1
x1
x1
x3
x1
x1
x4
x1
x4
x4
x2
4. MATERIALS SUPPLIED
4.1 PARTS SUPPLIED
Parts for your dishwasher will come in several plastic bags.
Check your parts bags shown to make sure you have all the
parts as listed to the left.
4.2 MANUAL BAG
The dishwasher comes with a manual bag containing:
• User manual,
• Installation manual and
• Quick reference guide.
4.3 DISHWASHER PARTS BAG 1
This dishwasher bag comes with the following parts:
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
c. Adjusting Wrench
d. Screws Ø 1/8” x 5/8” (Ø 3.5 mm x 14 mm)
e. Mounting Bracket Left
f. Mounting Bracket Right
g. Spring Clamp
h. Screw Clamp
j. Rubber Connector
k. Toe Kick Bracket - Left
l. Toe Kick Bracket - Right
m. Wire Nuts
n. Clips
o. Toe Kick (toe kick without slots)
p. Toe Kick
r. Screws Ø 1/8” x 3/8” (Ø 3.9 mm x 9 mm)
s. Plastic Caps
t. Screws Ø 3/16” x 1/4” (Ø 4mm x 6mm)
4.4 DISHWASHER PARTS BAG 2
In addition to the manual bag and the dishwasher parts bag 1
DWT 34, DWT 35, DWT 36 and DWT 37 (dishwasher models
which can accept a wooden kitchen door) also come with a
door panel installation kit which contains:
u. Template
v. Screws Ø
1/8
” x
5/8
” (Ø 3.5mm x 14mm)
y. Screws Ø
3/16
” x 1
3/4
” (Ø 4mm x 43mm)
4.5 PARTS ATTACHED TO THE REAR OF THE
DISHWASHER
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
o. Toe Kick (toe kick without slots)
p. Toe Kick

5USA
5. DISHWASHER SPECIFICATIONS
(8 1
mm - 911mm)
24
( 10
mm
)
24
( 10
mm
)
23
9/1

(598mm)
24 max
( 10mm max)
34
- 3
1/4

(8 4mm - 920mm)
33
7/8
- 35
7/8

5.1 TECHNICAL FEATURES
Load capacity 12 place settings
Permissible water
pressure 4.35 - 145 psi (0.3 - 10 bars)
Electrical connection 120 V (volts), 12 A (amps),
60 Hz (hertz)
Total power 1200 W (watts)
Heater power 1000 W (watts)
Notice :
Because we continually strive to improve our products, we may change our specifications
and design without prior notice. This device corresponds to the following directives:
UL 749 Household Dishwasher directive.

6USA
6. ENCLOSURE PREPARATION
Notice :
• For proper dishwasher operation and appearance ensure that the enclosure has the
minimum dimensions shown in the figure above.
6.1 ELECTRICAL PREPARATION
WARNING
To avoid electrical shock and/or a fire hazard, make sure electrical work is properly
installed. Only qualified electricians should perform electrical work.
Before installation disconnect the power supply to the work area by unplugging the
unit, “tripping” the circuit breaker or removing the fuse.
The installer has the responsibility of ensuring that the dishwasher electrical
installation is in compliance with all national and local electrical codes and ordinances.
The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected
to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker
rated for 15 amperes.
WARNING
Electrical supply cords must be a minimum #14AWG
copper wire.
Position the cable extending approximately 30” (760mm)
from the enclosure’s back (Figure A).
A
(
30)
B
C
Position the cable extending at the bottom
(Figure B).
Remove 2
15/16
” - 3
15/16
” (75mm-100mm) of the
cable’s outer casing, and then remove
3/8
” -
1/2
”
(9-13mm) of insulation from each wire. (Figure C)

7USA
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
B
B
A
A
WARNING
Dishwasher must be secured to adjacent
cabinetry using the mounting brackets
provided. Failure to do this may cause
damage to property or bodily injury.
Place the two mounting brackets into the top
corners of the dishwasher.
Fix the mounting brackets (A) to the top
corners of the dishwasher, with the screws
supplied.
Bend sides of mounting brackets (B) in order to
fix from sides (if necessary).
(8 1
mm - 911mm)
33
7/8
- 35
7/8

1
15/16

(50mm)
6.3 ADJUSTING HEIGHT
If the height of the enclosure is 337/8” to 357/8” (861 mm - 911mm) adjust supports as
shown in the figure.
Supplied (4)

8USA
Adjust the front foot level with the adjusting
wrench to balance and raise the dishwasher to the
enclosure height.
Adjust the rear foot level with a screwdriver to
balance and raise the dishwasher to the enclosure
height.
Notice :
• Make sure the dishwasher is plumb and
notice dishwasher can be placed with a small
clearance under the counter top.
• Turning the screwdriver in the direction of the
black arrows will bring the dishwasher back feet
up.
• Turning the screwdriver in the direction of the
white arrows will take the dishwasher rear feet
down.
T20
A
B
6.4 INSTALLING THE SIDE TRIM STRIPS
1. Remove the adhesive tape (Figure A).
Place the trim strips on the front edge of the side walls (Figure B).

9USA
6.5 PREPARING THE WATER CONNECTION (A)
Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder
connections must be made before the water line is connected to the dishwasher’s water
inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose
line.
Check with your plumbing supply sources for the proper hose and 90° elbow and
necessary fittings for the water supply line. This material is not supplied, and must be
purchased separately.
WARNING
Installation should be performed by a qualified installer. Work by unqualified
persons could be dangerous and may void the warranty.
If the dishwasher is installed in a location that experiences freezing temperatures
(e.g. in a vacation home, cabin etc.), you must drain all the water from the
dishwasher’s interior. Water system ruptures that occur as a result of freezing are
not covered by warranty.
A
B
C
6.5.1 INSTALLING THE 90° ELBOW FITTING
(B)
CAUTION
Do not over tighten the 90° elbow. Doing
so may damage the water inlet valve and
cause a water leak.
If the water supply line is to be copper
tubing, make certain that the elbow has a
compression fitting. Apply Teflon tape or other
pipe sealant when required. Orient the water
supply connection downwards as shown in the
figure so the water line can be easily pulled
underneath or on the side of the dishwasher.
6.5.2 JUNCTION BOX PREPARATION (C)
Remove the junction box cover by removing
the screws as shown in the figure. They will be
reinstalled later.

10 USA
6.6 DRAIN PREPARATION
The dishwasher drain hose may be connected to the drain plumbing in one of three ways
(Figure A, B, C).
Notice :
• Either one of the above methods must be used or the dishwasher will not operate
properly.
• A hose that attaches to a sink spray can burst if it is installed on the same water line as
the dishwasher. If your sink has one, it is recommended that the hose be disconnected
and the hole plugged.
• The total length of the drain hose is 76
3/4
” (1950mm). If a hose extension is required, a
drainage hose of equal quality must be used.
• The maximum length must not exceed 157 ½” (4000mm). Otherwise, the cleaning
process is negatively influenced.
A
B
C
6.6.1 UNDER THE SINK DRAIN
Install a Y-branch tail pipe. (Figure A)
Notice :
• You must add a loop at least 28" (710mm) above the floor of
the cabinet and above the drain connection in the drain hose
to prevent waste water from not draining properly, and causing
either poor washing results or a bad odor.
6.6.2 INSTALLING AN AIR GAP
If the local ordinance requires an air gap (Figure B).
Notice :
• Check with local ordinance for type of air gap required.
6.6.3 DISPOSAL
Remove the drain connection plug before attaching the drain
hose from the dishwasher.
Every disposal has a hook up for a dishwasher; consult your
disposer manual for correct connection. (Figure C)

11 USA
7. PLACEMENT OF DISHWASHER INTO THE OPENING
Now place the dishwasher into the opening and get ready to connect all hoses and
electrical connections.
CAUTION
Make sure all hoses
and electrical wire are
pulled through the side
opening of the cabinet,
no hoses are kinked
and all slack is taken
out as shown in the
above figure.
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL
CONNECTIONS
7.1.1 DRAIN HOSE CONNECTION
Connect the drain hose to the drain plumbing.
1. Use the supplied rubber connection hose and drain hose clamps to connect the
dishwasher drain hose to the plumbing drain connection.
2. Use the spring clamp to secure the rubber connection hose to the dishwasher drain
hose. Use the screw clamp to secure the rubber connection hose to the plumbing drain
connection.
Note that the marks on the
rubber connection hose
should be on the drain hose
side

12 USA
7.1.2 PREPERATION OF WATER SUPPLY & ELECTRICAL CONNECTIONS
AA
BB
CC
DD
Left side water supply
connection
Right side electrical
supply connection
Before pushing the
dishwasher in to the cabinet
you must place the electrical
cables and water supply
hoses into the channels of
the dishwasher (Figure A)
Place the supplied clips
into the channels (Figure
B) so that you can move
these clips along the
channels (Figure C) and fix
by pressing on (Figure D)
so that you can keep the
electrical cable and water
supply hose in the channels.

13 USA
F
E
F
GG
After installing one clip
for each side push the
dishwasher into the
cabinet (Figure E).
Note that while pushing
the dishwasher into
the cabinet, electrical
cable and water supply
hose must move in the
channels to the front
(Figure F).
Fix the second clip for
both sides (Figure G).

14 USA
7.1.3 WATER SUPPLY CONNECTION
Water supply may be connected to the
dishwasher in one of two ways:
• With metal braided hose.
• With copper tubing.
CAUTION
• Hot water supply line: Use minimum 3/8” O.D.
copper tubing or metal braided dishwasher
supply line.
• Temperatures required for soldering and
sweating will damage the dishwasher’s water
inlet valve so if any such operation is needed, keep the heat source min. 7
7/8
” (200mm)
away from the dishwasher’s water inlet valve.
• There should not be any sharp bends in the water line that may restrict the water flow.
• Te flon tape or pipe tread compound must be used for sealing the connection. Before
connecting the copper water supply line to the dishwasher, flush it with hot water to clear
any foreign material.
Notice :
After connections are made turn on the water supply to check for leaks.
7.1.4 ELECTRICAL CONNECTION
WARNING
• Make sure the voltage and frequency listed on the data plate correspond with
the household electrical supply. This data must correspond to prevent injury and
machine damage. Consult a qualified electrician if in doubt.
• Only connect the dishwasher to the mains when all installation and plumbing work
is complete.
• Do not use any extension cord or portable outlet device to connect the dishwasher
to a power supply.
7.1.5 GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown, grounding
will reduce the risk of electric shock by providing a path of least resistance for electric
current. This appliance must be installed and grounded in accordance with all local codes
and ordinances.
WARNING
• Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service representative if you
are in doubt whether the appliance is properly grounded.

15 USA
A
B
C
D
Install a strain relief (not supplied) into the
opening on the kick plate. (Figure A)
Pass the electrical supply cable through the
strain relief; make sure the strain relief clamps
the insulated outer casing of your electrical
supply cord and not the wires themselves.
Leave 2
15/16
” “ to 3
15/16
” “ (75mm / 100mm)
of insulated wire extending through the strain
relief (Figure B). Tighten the strain relief
screws. (Make sure you can not pull the
electrical cord out) of the strain relief.
Do not pre-twist the wires before connecting
them with wire nuts.
Using the supplied wire nuts, connect the
electrical supply wires to the dishwasher’s
wires, black to black, white to white, and green
or bare to green or bare. Make certain that the
insulated wires show no bare wire from the
bottoms of the wire nuts. Gently tug the wires
to make certain they are securely connected
(Figure C).
7.1.6 FASTEN JUNCTION BOX
1. Pull the wires into the junction box. Be sure
that the wire nuts do not loosen.
2. Replace the cover on the junction box.
3. Secure the cover with the screws (Figure D).

16 USA
7.3 ADJUSTING THE MOVABLE TOE KICK
Now that you have successfully installed the dishwasher, you
need to attach the toe kick to the dishwasher. The two piece toe
kick can be adjusted to the height and depth needed for your
kitchen. Be sure to use the slotted toe kick in the front and the
other behind it. They slide into each other.
1. Insert the movable toe kick brackets into the channel (A).
2. Make sure that the plastic tab to the left of
the “L” opening on the dishwasher has not closed the channel
you will push the bracket through.
Notice :
Be sure to notice there is a left and a right bracket.
Adjust the toe kick brackets forward or backwards so that they
will align with the kitchen toe kick (B).
Lock the toe kick brackets as shown with the plastic tab in the
figure C by pushing the plastic tab on the dishwasher into the
teeth of the bracket (C).
3. Now attach the toe kick to the bracket with the two (Ø
3/16
” x
1/4
” - Ø 4mm x 6mm) screws and the caps provided as follows.
Ø
1/8
" (3,5mm)
Ø
1/8
" (3,5mm)
A
B
C
7.2 READJUSTING FOOT
LEVELS
Now that the dishwasher is in the
cabinet you must readjust the feet to
bring the dishwasher up to the required
height and attach it underneath the
countertop.
1. Readjust the front foot levels with
adjusting wrench to balance the
dishwasher and raise it up under the
countertop, make sure the unit is level.
2. Readjust the rear foot levels with a
screwdriver to balance the dishwasher
and raise it to the required height using
the brackets supplied.
3. Attach the dishwasher underneath
the countertop with the four screws
supplied (Ø
1/8
” x
1/8
” - Ø 3.5mm
x 14mm). Make sure you do not go
through the top of the countertop or
damage granite.

17 USA
B
s
t
C
A
o
A
s
t
C
B
o
p
If the enclosure height is
below 33
1/16
” (840mm) use
only “o” labelled toe kick (toe
kick without slots). Installation
should be done following the
steps illustrated in the Figures
A, B and C respectively.
1. Bend tabs on toe kick (o)
inwards (A).
2. Secure toe kick to brackets
with screws (t) as shown in
the supply bags (B).
3. Attach caps (s) as shown in
the supply bags (C).
If the enclosure height is above 33
1/16
”
(840mm) use “o” and “p” labelled toe kicks
together. Make sure the slotted toe kick “p” is
on the outside so you can adjust height of the
toe kick. Installation should be done following
the steps illustrated in the figures A, B and C
respectively.
1. Align the toe kick (o) and (p) (A).
2. Secure toe kicks to brackets with screws (t)
after adjusting the height of the slotted toe
kick (p) (B).
3. Attach caps (s) as shown in the supply bags
(C).
7.4 INSTALLING THE OUTER DOOR
(DWT 34200, DWT 35200, DWT 36200, DWT
37200, DWT 34400)
Measure the height and width of the enclosure
(Figure A) and the toe kick. Determine how big
the wooden door can be. For example if the height
is 33
7/8
” (860mm) and if the toe kick is 3
15/16
”
(100mm) the door can not be taller than 29
15/16
”
(760mm).
1. Prepare the wooden door with the mounting
brackets.
Height : Height of the wooden door 30”
(760mm)
Width : 23 ¼” to 23 ½” (592mm - 595mm)
Thickness : ¾ “ (19mm)
?
?
A