Blomberg KQD 1360X User manual

Instruction manual
KQD 1360X
Refrigerator
ררקמ

Please read this manual first!
Dear Customer,
We hope that your product, which has been produced in modern plants and
checked under the most meticulous quality control procedures, will provide you an
effective service.
For this, we recommend you to carefully read the entire manual of your product
before using it and keep it at hand for future references.
This manual
• Will help you use your appliance in a fast and safe way.
• Read the manual before installing and operating your product.
• Follow the instructions, especially those for safety.
• Keep the manual in an easily accessible place as you may need it later.
• Besides, read also the other documents provided with your product.
Please note that this manual may be valid for other models as well.
Symbols and their descriptions
This instruction manual contains the following symbols:
CImportant information or useful usage tips.
AWarning against dangerous conditions for life and property.
BWarning against electric voltage.
This product bears the selective sorting symbol for waste electrical and
electronic equipment (WEEE).
This means that this product must be handled pursuant to European Directive
2002/96/EC in order to be recycled or dismantled to minimise its impact on
the environment. For further information, please contact your local or regional
authorities.
Electronic products not included in the selective sorting process are potentially
dangerous for the environment and human heatlh due to the presence of
hazardous substances.
Recycling

EN
2
1 The refrigerator 4
2 Important Safety
Warnings 5
Intended use ..................................... 5
General safety ................................... 5
Child safety........................................ 7
HCA Warning .................................... 7
Things to be done for ....................... 7
energy saving .................................... 7
3 Installation 8
Points to be considered when re-
transporting your refrigerator .............8
Before operating your refrigerator ...... 8
Electric connection ............................ 8
Disposing of the packaging ...............9
Disposing of your old refrigerator ....... 9
Placing and Installation ...................... 9
Floor balance adjustment ................10
Adjusting the gap between the upper
door ................................................ 10
Installing Water Filter ....................... 12
Connection of the Water Pipe to the
Refrigerator ..................................... 12
Connection of Water Hose to the
Jug ................................................. 13
Connection of the Water Pipe to the
Cold Water Mains Line .................... 14
Prior to first use of Water Dispenser. 16
CONTENTS
4 Preparation 17
5 Using your refrigerator 18
Indicator Panel................................. 18
Door Open Alarm: .......................... 21
Things to do to have the filter usage
time calculated automatically ........... 22
Sliding Body Shelves ....................... 23
Egg tray........................................... 23
Crisper ............................................ 23
Chiller compartment ........................ 23
Movable Middle Section .................24
Flexi Zone Storage Compartment .. 24
Blue light ......................................... 24
Sliding Body Shelves With Rear
Hangers .......................................... 25
Butter & Cheese Section ................. 25
Using the water spring..................... 25
Spillage Tray .................................... 25
Minibar ............................................ 26
6 Cleaning and care 27
Protection of plastic surfaces ..........27
7 Recommended solutions
for the problems 28

EN
3
17
18 19
2
3
6
7
8
9
5
4
16
13
11
14
1
12
10
15
1The refrigerator
1- Fridge compartment door shelves
2- Fridge compartment glass shelves
3- Diffuser cover
4- Illumination lens
5- Movable middle section
6- Chiller compartment
7- Crisper
8- Icematic
9- Frozen food storage compartments
10- Minibar
11- Bottle holder
12- Bottle shelf
13- Food storage compartment shelves
14- Food storage compartments
15- Water Filter
16- Butter & Cheese shelf
17- Fridge compartment
18- Freezer compartment
19- Flexi Zone
CFigures that take place in this instruction manual are schematic and may not
correspond exactly with your product. If the subject parts are not included in the
product you have purchased, then it is valid for other models.

EN
4
2Important Safety Warnings
• Please review the following information.
If these are not followed, personal
injury or material damage may occur.
Otherwise, all warranty and reliability
commitments will become invalid.
The usage life of the unit you purchased
is 10 years. This is the period for keeping
the spare parts required for the unit to
operate as described.
Intended use
• This product is designed for domestic
use.
• It should not be used outdoors. It is not
appropriate to use it outdoor even if the
place is covered with a roof.
General safety
When you want to dispose/scrap the
product, we recommend you to consult
the authorized service in order to learn
the required information and authorized
bodies.
• Consult your authorized service for all
your questions and problems related to
the refrigerator. Do not intervene or let
someone intervene to the refrigerator
without notifying the authorised
services.
• Do not eat cone ice cream and ice
cubes immediately after you take them
out of the freezer compartment! (This
may cause frostbite in your mouth.)
• Do not put bottled and canned liquid
beverages in the freezer compartment.
Otherwise, these may burst.
• Do not touch frozen food by hand; they
may stick to your hand.
• Vapor and vaporized cleaning materials
should never be used in cleaning
and defrosting processes of your
refrigerator. In such cases, the vapor
might get in contact with the electrical
parts and cause short circuit or electric
shock.
• Never use the parts on your refrigerator
such as the door and drawer as a
means of support or step. You may
cause the product to tip over or parts of
it get damaged.
• Do not use electrical devices inside the
refrigerator.
• Do not damage the cooling circuit,
where the refrigerant is circulating, with
drilling or cutting tools. The refrigerant
that might blow out when the gas
channels of the evaporator, pipe
extensions or surface coatings are
punctured may cause skin irritations
and eye injuries.
• Do not cover or block the ventilation
holes on your refrigerator with any
material.
• Repairs of the electrical products must
only be made by qualified persons.
Repairs performed by incompetent
persons may create a risk for the user.
• In case of any failure or during a
maintenance or repair work, disconnect
your refrigerator’s mains supply by
either turning off the relevant fuse or
unplugging your appliance.
• Do not pull by the cable when pulling
off the plug.
• Place the beverage with higher proofs
tightly closed and vertically.
• Flammable items or products that
contain flammable gases (e.g. spray) as
well as the explosive materials should
never be kept in the product.

EN
5
• Do not use mechanical devices
or other means to accelerate the
defrosting process, others than those
recommended by the manufacturer.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
• Do not operate a damaged refrigerator.
Consult your service if you have any
doubts.
• Electrical safety of your refrigerator shall
be guaranteed only if the earth system
in your house complies with standards.
• Exposing the product to rain, snow, sun
and wind is dangerous with respect to
electrical safety.
• If there is any problem with the power
cable or the plug, they must be
replaced by the authorised service in
order to avoid any accidents.
• Never plug the refrigerator into the wall
outlet during installation. Otherwise, risk
of death or serious injury may arise.
• Intended use of the product is to
preserve foods; it should never be used
for other purposes.
• Rating plate containing product's
technical specifications is in the inner
left part of the product.
• Connecting the product to electric
energy saving systems is risky as it may
cause damage on the product.
• If your product is equipped with blue
light, the light should not be looked into
by optical appliances.
• In products with mechanical control
(thermostat), wait for 5 min. to re-plug
the product if it is unplugged.
• This operation manual should be
handed in to the new owner of the
product when it is given to others.
• Power cable and plug should not be
damaged when moving the refrigerator.
To avoid risk of fire, the cable should
not be kinked or put under heavy
things. Do not touch the plug with wet
hands when plugging the product.
• The product should not be plugged if
the receptacle is loose.
• Water should not be sprayed directly on
inner or outer parts of the product for
safety purposes.
• Flammable pressurized sprays should
not be sprayed near the product to
avoid risk of fire or explosion.
• Containers with liquid inside should
not be placed on top of the product.
Spilling water on an electrical
component may cause electric shocks
or risk of fire.
• Foods more than the capacity of the
product should not be kept in the
product. It may fall when the door is
opened and cause injury or damage.
Similar problems may occur in case of
putting things on the product.
• Products that need a precise
temperature control (vaccines, heat-
sensitive medicine, scientific materials,
etc.) should not be kept in the
refrigerator.

EN
6
• Refrigerator should be disconnected if it
is not going to be used for a long time.
Any problem in the cable insulation may
cause fire.
• Dirt and dusts on tip of the electric plug
must be cleaned, otherwise, they may
cause risk of fire.
• The product may move when level
adjustment feet of the product do not
stand on the floor well.
• If your product has a door handle, the
product must not be pulled by the
handle, because the handle may be
forced out.
•Care should be paid as there is risk of
squeezing hands or feet between the
movable parts inside the product.
Child safety
• If the door has a lock, the key should
be kept away from reach of children.
• Children should be supervised to
ensure that they do not play with the
appliance
HCA Warning
If your product is equipped with a
cooling system that contains R600a:
• This gas is flammable. Therefore, pay
attention to not damaging the cooling
system and piping during usage and
transportation. In the event of damage,
keep your product away from potential
fire sources that can cause the product
catch a fire and ventilate the room in
which the unit is placed.
Ignore the warning if your product is
equipped with a cooling system that
contains R134a.
You can see the gas used in production
of your product on the rating plate that is
located on the left inner part of it.
Never dispose the product in fire.
Things to be done for
energy saving
• Do not leave the doors of your
refrigerator open for a long time.
• Do not put hot food or drinks in your
refrigerator.
• Do not overload your refrigerator so
that the air circulation inside of it is not
prevented.
• Do not install your refrigerator under
direct sunlight or near heat emitting
appliances such as ovens, dishwashers
or radiators.
• Pay attention to keep your food in
closed containers.
• Maximum amount of food can be put in
your refrigerator's freezer compartment
when the freezer compartment shelf or
drawer is removed. Declared energy
consumption value of your refrigerator
was determined when the freezer
compartment shelf or drawer was
removed and under maximum amount
of food load. There is no risk in using a
shelf or drawer according to the shapes
and sizes of the foods to be frozen.

EN
7
3Installation
CPlease remember that the manufacturer
shall not be held liable if the information
given in the instruction manual is not
observed.
Points to be considered
when re-transporting your
refrigerator
1. Your refrigerator must be emptied and
cleaned prior to any transportation.
2. Shelves, accessories, crisper and etc.
in your refrigerator must be fastened
securely by adhesive tape against any
jolt before repackaging.
3. Packaging must be tied with thick
tapes and strong ropes and the rules of
transportation printed on the package
must be followed.
CAlways remember...
Every recycled material is an
indispensable source for the nature and
for our national resources.
If you wish to contribute to recycling the
packaging materials, you can get further
information from the environmental
bodies or local authorities.
Before operating your
refrigerator
Before starting to use your refrigerator
check the following:
1. Is the interior of the refrigerator dry and
can the air circulate freely in the rear of
it?
2. Insert the 2 plastic wedges onto the
rear ventilation cover as illustrated in
the following figure. To do this, remove
the screws on the product and use the
screws given in the same pouch.
Plastic wedges will provide the required
distance between your refrigerator
and the wall in order to allow the air
circulation.
3. Clean the interior of the refrigerator as
recommended in the “Maintenance and
cleaning” section.
4. Plug the refrigerator into the wall outlet.
When the door is open the respective
interior light will come on.
5. You will hear a noise as the compressor
starts up. The liquid and gases sealed
within the refrigeration system may
also give rise to noise, even if the
compressor is not running and this is
quite normal.
6. Front edges of the refrigerator may
feel warm. This is normal. These areas
are designed to be warm to avoid
condensation.

EN
8
Electric connection
Connect your refrigerator to a grounded
socket which is being protected by a
fuse with the appropriate capacity.
Important:
BThe connection must be in compliance
with national regulations.
BThe power cable plug must be easily
accessible after installation.
B Voltage and allowable fuse protection
are specified in the “Technical
Specifications” section.
BThe specified voltage must be equal to
your mains voltage.
BExtension cables and multiway plugs
must not be used for connection.
BA damaged power cable must be
replaced by a qualified electrician.
BThe appliance must not be operated
before it is repaired! There is danger of
electric shock!
Disposing of the packaging
AThe packing materials may be
dangerous for children. Keep the
packing materials out of the reach
of children or dispose them of by
classifying them in accordance
with the waste instructions. Do not
dispose them of along with the normal
household waste.
The packing of your refrigerator is
produced from recyclable materials.
Disposing of your old
refrigerator
Dispose of your old machine without
giving any harm to the environment.
AYou may consult your authorized dealer
or waste collection center of your
municipality about the disposal of your
refrigerator.
A Before disposing of your refrigerator,
cut out the electric plug and, if there
are any locks on the door, make them
inoperable in order to protect children
against any danger.
Placing and Installation
BCaution: Never plug the refrigerator
into the wall outlet during installation.
Otherwise, risk of death or serious injury
may arise.
AIf the entrance door of the room
where the refrigerator will be installed is
not wide enough for the refrigerator to
pass through, than call the authorised
service to have them remove the doors
of your refrigerator and pass it sideways
through the door.
1. Install your refrigerator to a place that
allows ease of use.
2. Keep your refrigerator away from
heat sources, humid places and direct
sunlight.
3. There must be appropriate air
ventilation around your refrigerator in
order to achieve an efficient operation.
If the refrigerator is to be placed in a
recess in the wall, there must be at least
5 cm distance with the ceiling and at
least 5 cm with the wall.
If the floor is covered with a carpet, your
product must be elevated 2.5 cm from
the floor.
4. Place your refrigerator on an even
floor surface to prevent jolts.
5. Do not keep your refrigerator in
ambient temperatures under 10°C.

EN
9
Floor balance adjustment
AIf your refrigerator is unbalanced;
BFirst unplug the product. The product
must be unplugged when making the
balance adjustment. There is the risk of
electric shock.
4
1 2 3
1- Ventilation cover is removed by
unscrewing its screws as illustrated in
the figure before the procedure. You
can balance your refrigerator by turning
the front legs of it as illustrated in the
figure. The corner where the leg exists is
lowered when you turn in the direction of
black arrow and raised when you turn in
the opposite direction. Taking help from
someone to slightly lift the refrigerator will
facilitate this process.
2. After the balance issue is remedied,
install back the ventilation cover and
fasten the screws.
3. Remove the screws fastening the
lower ventilation cover using a Philips
screwdriver.
Adjusting the gap between
the upper door
CYou can adjust the gap between the
fridge compartment doors as illustrated
in the figures.
Door shelves should be empty when
adjusting the door height.
C Using a screwdriver, remove the
screw of upper hinge cover of the door
you want to adjust.

EN
10
C Adjust the door appropriately as you
desire by loosing the screws.
C Fix the door you have adjusted by
tightening the screws without changing
the position of the door.
C Replace the hinge cover and fix with
the screw.

EN
11
Installing Water Filter
(in some models)
Two different water sources may
be connected to the refrigerator for
water supply: the mains cold water
supply and water in a jug.
Installation Requirements
A pump should be used for jug water
usage.
Check that the parts stated below are
supplied with your appliance.
1. Union for connection of the water
pipe to the rear of the appliance. (If it
does not fit, provide it from the nearest
authorized service.)
2. 2 pieces of pipe clips (In case required
to secure the water pipe)
Note: Since the following parts are not
required in use with a jug, they may not
be found in the product you purchased.
3. 5-meter long water pipe (1/4 inch in
diameter)
4. Cold mains water valve with mesh filter
(Tap Adapter)
5. Water Filter or externally connectable
filter to be fitted to the bracket inside
the fridge compartment.
Place where the external filter is going to
be fitted should be determined first.
(Applies to the filter being used outside
the refrigerator.) Then, determine the
distance between the filter and the
refrigerator and required hose lengths
from the filter to the refrigerator water
inlet.
Water filter must be hold upright as shown
in the figure. It is important to properly
attach the filter to water inlet and water
outlet points.
After attaching the filter, do not use first 3-4
glasses of water.
Connection of the Water
Pipe to the Refrigerator
1. After installing the union onto the
water pipe, insert the water pipe to
the refrigerator inlet valve by pressing
downwards firmly.
2. Fix union as seen in the opposite
figure, by squeezing by hand on the
refrigerator inlet valve.
(a- Water Pipe, b-Union, c-Valve)
CNote 1: You should not need to
tighten the union with a tool to achieve
water tight assembly. In case of a leak
use a spanner or a pair of pliers to
tighten the union.
3
1
4
2
5
c
a
a
b
1
2

EN
12
Connection of Water Hose to
the Jug
(in some models)
To connect water to the refrigerator from
a jug, a pump is needed. Follow the
instructions below after connecting one
end of the water pipe coming out of the
pump to the refrigerator as described on
the previous page.
1. Finish the connection by pushing the
other end of the water pipe into the
water pipe inlet of the pump as shown
in the figure.
2
1a
1b
2. Put and fix the pump hose into the jug
as shown in the figure.
3. After completing the connection, plug in
and run the pump.
To provide an efficient operation of the
pump, wait for 2-3 minutes after
starting the pump.
CYou may refer to the user manual
of the pump while making the water
connection.
CThere is no need to use water filter in
case a jug is used.
CPump must be used when jug will be
used.

EN
13
Connection of the Water
Pipe to the Cold Water Mains
Line
(in some models)
If you want to use your refrigerator by
connecting it to the cold water mains
line,
you will have to connect a standard 1/2"
valve connection fitting to the cold water
supply in your house. In case this valve is
not present or in case you are not sure,
consult a qualified plumber.
1. Separate the union from the tap
adaptor. (Figure A)
2. Install the tap adaptor to 1/2” valve
fitting as shown in the figure. (Figure B)
3. After inserting the water pipe to the
union, install it to the tap adaptor and
insert to the tap as shown in the figure.
(Figure C)
4. Tighten the union manually. In case of a
leak use a spanner or a pair of pliers to
tighten the union.
ACaution: Secure the water pipe
to suitable points by means of the
pipe clips supplied to avoid any
damage or displacement or accidental
disconnection.
ACaution: After turning on the water
valve, make sure that there is no leakage
at both connection points of the water
pipe. In case of a leak, turn off the valve
immediately and tighten all joints again
using a spanner or a pair of pliers.
ACaution: Make sure that standard
1/2" valve fitting fed by cold mains water
supply is available and is turned off fully.

EN
14
To fit the water filter follow the
instructions below referring to figures
supplied:
1. Press ice cancel button on the display.
2. Remove the filter cover in the fridge
compartment by pulling it forward.
3. Take out the water filter by-pass cover
by rotating it downwards.
ACaution: Make sure that the “Ice off”
mode is active before taking out the by-
pass cover.
Note: It is normal that a few drops of
water drip after the cover has been taken
out.
4. Remove the lid on top of the water filter
to place it as shown in the figure and
turn upwards to lock it.
5. Press ice cancel button on the display
again to exit from this mode.
Water filter should be replaced every 6
months.
If you want to have the filter change time
calculated automatically and receive a
warning at the end of usage time, please
read "Calculating the Filter Usage Time
Automatically" section.

EN
15
The water filter must be removed as
shown in the figure when it is going to
be replaced or when it will no longer
be used and by-pass cover must be
attached. It must be made sure that Ice
Off mode is active before taking it out.
ACaution: Water filter cleans some
foreign particles in the water. It does not
purify water from microorganisms.
ACaution: Ice Off button must always
be pressed during replacement of the
water filter or installing the by-pass
cover.
Prior to first use of Water
Dispenser
CWater mains pressure must not be
below 1 bar.
CWater mains pressure must not be
above 8 bars.
CPumps must be used in case the
supply water pressure drops below 1 bar
or if a jug is going to be used.
CWater system of the refrigerator must
be connected to the cold water line. It
must not be connected to hot water line.
CNo water may be obtained in the
initial operation of the refrigerator. This
is caused by the air in the system. To
discharge air from the system, press
Dispenser latch for periods of 1 minute
until water comes from the Dispenser.
Water flow may be irregular in the
beginning. Irregular water flow will be
normalized after the air in the system is
discharged.
CAt the initial startup of the refrigerator
approx.12 hours must pass before cold
water can be obtained.
CWater mains pressure must be
between 1-8 bars for the operation of
Ice/Water Dispenser smoothly. For this,
check that 1 glass of water (100 cc) can
be filled in 10 seconds.
CThe first 10 glasses of water should
not be consumed.
CApproximately the first 30 cubes
of ice to be obtained from the Ice
Dispenser must not be used.
CAlways use the water filter when a jug
is not being used.

EN
16
4Preparation
CYour refrigerator should be installed at
least 30 cm away from heat sources
such as hobs, ovens, central heater
and stoves and at least 5 cm away
from electrical ovens and should not be
located under direct sunlight.
CThe ambient temperature of the room
where you install your refrigerator
should at least be 10°C. Operating your
refrigerator under cooler conditions
than this is not recommended with
regard to its efficiency.
CPlease make sure that the interior of
your refrigerator is cleaned thoroughly.
CIf two refrigerators are to be installed
side by side, there should be at least 2
cm distance between them.
CWhen you operate your refrigerator
for the first time, please observe the
following instructions during the initial
six hours.
- The door should not be opened
frequently.
- It must be operated empty without
any food in it.
- Do not unplug your refrigerator. If
a power failure occurs out of your
control, please see the warnings in
the “Recommended solutions for the
problems” section.
COriginal packaging and foam
materials should be kept for future
transportations or moving.

EN
17
1 7 11 12 15 4
5
6
2
3
16
17
18 20 19
10 9 14 138
5Using your refrigerator
Indicator Panel
This touch-control indicator panel allows you to set the temperature without opening
the door of your refrigerator. Just touch the relevant button with your finger to set the
temperature.
1. Eco Extra/Vacation Button
2. Fast Freeze Button
3. Freezer Compartment Temperature
Setting Button
4. Fridge Compartment Temperature
Setting Button
5. Quick Cool Button
6. Flexi Zone Compartment Temperature
Setting Button
7. Vacation Function Indicator
8. Eco Extra Function Indicator
9. Quick Freeze Function Indicator
10. Freezer Compartment Temperature
Indicator
11. Fridge Compartment Temperature
Indicator
12. Quick Cool Function Indicator
13. Flexi Zone Storage Compartment
Temperature Indicator
14. Economy Mode Indicator
15. Error Status Indicator
16. Key Lock Indicator
17. Ice Cancel Button
18. Ice Off indicator
19. Cancel Filter Change Warning Button
20. Filter Change Warning Indicator

EN
18
1. Eco Extra/Vacation Button
Press this button briefly to activate the
Eco Extra function. Press and hold this
button for 3 sec. to activate the Vacation
function. Press this button again to
deactivate the selected function.
2. Fast Freeze Button
Press this button briefly to activate the
Fast Freeze function. Press this button
again to deactivate the selected function.
3. Freezer Compartment
Temperature Setting Button
Press this button to set the temperature
of the freezer compartment to -18, -20,
-22, -24, -18... respectively. Press this
button to set the desired temperature for
the Freezer Compartment.
4. Fridge Compartment Temperature
Setting Button
Press this button to set the temperature
of the fridge compartment to 8, 6, 4, 2,
8... respectively. Press this button to set
the desired temperature for the Fridge
Compartment.
5. Quick Cool Button
Press this button briefly to activate the
Quick Cool function. Press this button
again to deactivate the selected function.
6. Flexi Zone Compartment
Temperature Setting Button
You can set the Flexi Zone Compartment
either as a Freezer or a Cooler.
Press and hold this button for a long
time (3 sec) to set the Flexi Zone
Compartment as a Freezer or a Cooler.
This compartment is set as a Freezer
Compartment at factory.
If the Flexi Zone Compartment is set as a
Freezer, then the temperature of the Flexi
Zone Compartment will change as -18,
-20, -22, -24, -18... respectively each
time you press this button. If the Flexi
Zone Compartment is set as a Fridge,
then the temperature of the Flexi Zone
Compartment will change as 10, 8, 6,
4, 2, 0, -6, ... respectively each time you
press this button.
7. Vacation Function Indicator
Indicates that the vacation function
is active. If this function is active,
"- -" appears on the indicator of the
fridge compartment and no cooling is
performed in the fridge compartment.
Other compartments will be cooled in
accordance with the temperature set for
them.
Press the relevant button again to
deactivate this function.
8. Eco Extra Function Indicator
It indicates that the Eco-Extra function
is active. If this function is active, your
refrigerator will automatically detect
the least usage periods and energy-
efficient cooling will be performed during
those times. Economy indicator will be
active while energy-efficient cooling is
performed.
Press the relevant button again to
deactivate this function.

EN
19
9. Quick Freeze Function Indicator
It indicates that the Fast Freeze function
is active. Use this function when
you place fresh food into the freezer
compartment or when you need ice.
When this function is active, your
refrigerator will run for a certain period of
time.
Press the relevant button again to
deactivate this function.
10. Freezer Compartment
Temperature Indicator
It indicates the temperature set for
Freezer Compartment.
11. Fridge Compartment
Temperature Indicator
Indicates the temperature set for Fridge
Compartment.
12. Quick Cool Function Indicator
Indicates that the Quick Cool function is
active. Use this function when you place
fresh food into the fridge compartment
or when you need to cool your food
quickly. When this function is active, your
refrigerator will run for 2 hours without
stopping.
Press the relevant button again to
deactivate this function.
13. Flexi Zone Storage Compartment
Temperature Indicator
It indicates the temperature set for Flexi
Zone compartment.
14. Economy Mode Indicator
Indicates that the refrigerator is running
in energy-efficient mode. Freezer
Compartment temperature
This indicator will be active if the function
is set to -18 or the energy efficient
cooling is being performed due to Eco-
Extra function.
15. Error Status Indicator
If your refrigerator does not cool
adequately or if there is a sensor failure,
this indicator will be activated. When this
indicator is active, Freezer Compartment
Temperature indicator will display "E"
and Fridge Compartment Temperature
Indicator will display numbers such
as "1,2,3…". These numbers on the
indicator provides information about the
error to the service personnel.
16. Key Lock Indicator
Use this function if you do not want your
refrigerator temperature setting changed.
Press Quick Cool Button and Flexi Zone
Compartment Temperature Setting
Button simultaneously for a long time (3
sec) to activate this feature.
Press the relevant buttons again to
deactivate this function.
17. Ice Cancel Button
To stop ice formation, ice cancel button
is pressed for 3 seconds. When ice
cancel is selected, no water will be sent
to the ice box. Despite this, some ice
may be leftover in the ice box which
may be taken from there. To restart ice
formation, ice cancel button has to be
pressed for 3 seconds.