Bluefin SUP Cruise User manual

UK. Instruction Manual Inatable SUP
DE. Bedienungsanleitung Aufpumpbares SUP
ES. Manual de instrucciones SUP hinchable
FR. Guide d’utilisation SUP Gonable
IT. Manuale di Istruzioni SUP Gonabile

Hey,
Welcome to the Bluen SUP Community! Your journey doesn’t end at the point of
purchase - as a Bluen crew member you’re entitled to many benets including 5-year
product warranty and lifetime support from our customer service team.
We hope you enjoy your product and choose to explore the full Bluen SUP range. To
get the best out of your product, please consult this manual before use. Additional
resources can be found at www.bluensupboards.com
The Bluen SUP Team
JOIN THE OWNER’S CLUB: For even more support, skills, tips
and tricks, to share SUP stories, photos and videos of your
adventures and more - please join the Bluen SUP Paddle Board
- Owners Club on Facebook. As a member of this ever-expanding
online community you’ll have the full support of Bluen crew
members and board owners just like you!
facebook.com/groups/BluenSUPCommunity
01 | WELCOME TO THE COMMUNITY

Unpack and unroll your Bluen SUP on a smooth, clean, at surface.
Connect the air tap on your pump to the ination valve on your SUP. Firmly push
the air tap inwards and twist clockwise to secure the connection (Figure 1).
Before you begin to pump, please consult the recommended PSI on the valve(s)
of your SUP and inate to the appropriate value. DO NOT over-inate your SUP.
The PSI may not register on your pump until you reach at least 7 PSI - keep
pumping!
Once the desired air pressure has been reached, please safely disconnect the air
tap of your pump and secure the valve on your SUP.
WARNING: Please only use the pump provided or other
recommended pumps. DO NOT use an air compressor as you
will risk over-inating the board and severely damaging your SUP
beyond repair. Your warranty will be void in the event of damage
via over-ination.
Figure 1.
INFLATION OPERATION | 02

Insert the n into the n box slot via the end gap (Figure 1).
Firmly push the other end of the n down and lock into place by pushing the end
clasp back down (Figure 2).
Figure 1.
Figure 1.
03 | FIN ATTACHMENT
Smart Lock Fin
Smart Lock Fin System
US Box Fin
Figure 2.
FIN TYPE: Your SUP either
has a US Box Fin or Smart
Lock Fin System. Please
check your n type and
follow the necessary
instructions. TIP: Before
you begin please ensure
the n box slot is clean
and free of sand and grit.

Unscrew the plate from the screw (Figure 1) and place into the n slot via the gap
(Figure 2). TIP: Use the screw to slide the plate into place along the slot.
Insert the n into the n box slot via the central gap, slide the n to the back and
rmly push down the other end (Figure 3).
Line up the screw with the screw plate and tighten until fully secure (Figure 4).
FIN ATTACHMENT | 03
Figure 3.
Figure 1.
US Box Fin System
Figure 4.
Figure 2.

Figure 1.
SUP PADDLE: Your 3-Piece paddle
easily connects together and is fully
height adjustable. The ergonomic
grip should be handled as illustrated
(Figure 1). The logo on the blade
should face away from you when
paddling.
04 | PADDLE

KAYAK PADDLE: If your package came with a Kayak Conversion
Kit (only available on select models), then the 3-Piece paddle
easily converts into a kayak paddle using the extra blade. Simply
swap the adjustable T-bar for the extra blade, pop into place and
fasten the clasp. TIP: For kayak conguration, have both blades
symmetrical and the logo on the blades facing towards you in
order to grab more water whilst paddling.
PADDLE | 04

NB: The Kayak Conversion Kit
is only included with select
models.
For comfort, balance & performance, the kayak seat should be attached at the
rear of the board, just behind the central carry handle.
Securely attach the top two straps to the forward-facing D-rings (Figure 1).
Securely attach the bottom two straps to the rear D-rings (Figure 2).
Tighten all straps so that the seat is both comfortable and rmly upright.
Figure 2.
Figure 1.
05 | KAYAK CONVERSION

Before deating the board, please remove the large central n and ensure it is
clean and free of sand and debris. Hose down if necessary to prevent mildew
build-up in storage. Do not use harsh chemicals for cleaning. Most dirt can be
removed with mild soap and water.
Deate each valve on the SUP by rst removing the valve cap. Next, you can
release some pressure by slightly pushing on the push-pin. TIP: Don’t face
directly over the valve when releasing the initial blast of air. To fully deate the
board, please push rmly on the push-pin and twist the knob in any direction to
lock into place. Your board will now rapidly deate.
To ensure full deation, you can kneel & crawl, or sit over parts of the board to
force the remaining air out. Once fully deated, please re-attach the valve caps.
For compact storage your board should be as at as possible. Once attened,
please roll and fold the board from the nose down (Figure 1).
Please pack and store the SUP in the backpack provided in a cool dry place
and away from direct sunlight. TIP: For added protection from damp, use the
polythene bag that your board was initially packed and sealed in.
Figure 1.
PACKING AWAY | 06

For your own safety please attach the coiled leash provided to your calf or ankle
at all times. Secure one end to the D-ring at the rear of the board and securely
attach the velcro strap to your calf or ankle.
Whilst paddling please consider appropriate clothing for the weather or climate.
It is highly recommended to wear a buoyancy aid vest or other personal otation
device, and a wetsuit in cooler conditions.
Stay hydrated by packing a water bottle in your cargo area. You can secure a bag
or cooler under the cargo bungees with ease.
Store your mobile phone in the waterproof case provided. Also, consider packing
a whistle or ashlight in case of an emergency.
Your board can expand and over-inate in very hot temperatures. Please check
the air pressure and deate your board as necessary.
Please pack and store the SUP in the backpack provided, in a cool dry place and
away from direct sunlight.
You should clean and maintain your board after each use. Hose down if
necessary to prevent mildew build-up in storage. Do not use harsh chemicals for
cleaning. Most dirt can be removed with mild soap and water.
A repair kit is provided, with extra patches and a valve tightening tool. From time-
to-time your valve may need tightening to prevent any air leaks. To tighten the
valve rst ensure that the board is fully deated. Insert the tool into the valve and
push upwards from the underside of the board to ensure that the valve is making
rm contact with the thread. Next, turn the tool clockwise until the valve is fully
tightened and secure.
Please ensure that no water gets inside of your SUP as this can severely damage
the board. If water gets inside the valve, then please remove the valve using the
tool provided. Drain any water and dry thoroughly before re-attaching the valve
and inating.
07 | SAFETY & CARE

Fault
My pump isn’t working.
My board has a puncture
/ leak.
Inspection
Check whether the hose
is blocked or damaged in
any way.
The connection between
the hose / Air Pump /
ination valve on your
inatable is not secure.
The PSI gauge isn’t
working.
With the board inated,
apply dish-washing liquid
to a cloth and coat the
valve.
With the board inated,
apply dish-washing liquid
to a cloth and coat the
deck and sides.
Solution
Remove any blockages from the hose, or
replace if damaged.
Pause the ination, check all connections are
secure and reinstall if necessary.
The PSI value won’t usually register until it
reaches 7 PSI.
If the problem persists, please contact
us. Additional resources may be found at
www.bluensupboards.com/info-zone/
maintenance-repair/
If bubbling occurs, your valve will most likely
need tightening using the tool provided.
Deate your board, reach for the nut from
underneath the board, insert the valve
tightening tool and twist clockwise until fully
tightened and secure.
If bubbling occurs on the seams and deck-pad
then you can easily repair a puncture with the
patches provided and a strong adhesive glue.
Apply glue to both the aected area on the
board and the underside of the patch. Allow
the glue to become tacky before applying the
patch. TIP: You can heat the area with a
hair-dryer to speed up the drying process.
If the problem persists, please contact
us. Additional resources may be found at
www.bluensupboards.com/info-zone/
maintenance-repair/
TROUBLESHOOTING | 08

Fault
One or some of my
D-rings has come unstuck
or has fallen o.
There is a bump on the
underside of my board.
My SUP won’t t back
into the backpack.
Inspection
Check whether you just
need to glue the D-ring
back on, or if you require
a new one.
A bump is clearly visible
on the bottom of the
board underneath the
valve.
The board is a very tight-
t and doesn’t appear to
t back into the backpack.
Solution
Use a strong adhesive glue to re-apply the
D-ring, source a new D-ring from a supplier or
contact us for a replacement.
If the problem persists, please contact
us. Additional resources may be found at
www.bluensupboards.com/info-zone/
maintenance-repair/
Don’t worry. This naturally occurs on every
paddle board. Sometimes it is covered by a n
box or other detail, but is exposed on certain
models. It occurs due to a gap in the drop-
stitch to make space for the valve. It won’t
aect the performance or quality of your SUP
in any way.
Unfold the SUP and ensure that all of the air
has been squeezed out. You can crawl on the
board on your knees, or apply pressure by
sitting on it to get the SUP as at and deated
as possible. Roll the SUP up in approximately
1ft increments and re-pack. For some larger
models, it may help to fold the sides inwards
before rolling.
If the problem persists, please contact
us. Additional resources may be found at
www.bluensupboards.com/info-zone/
maintenance-repair/
08 | TROUBLESHOOTING

Fault
The n won’t t into the
n box.
I keep losing my n. Why
is it so heavy?
Water or moisture has
entered my SUP.
Inspection
The n box has warped
and the n won’t slot
back in.
Check the n-box for
damage and reassess the
n attachment procedure
for your particular n
system.
Immediate action is
required.
Solution
Heat up the plastic on the n box with a hair-
dryer, which should allow you to squeeze the
n back in. Leave the n in the n box for a
few hours so that the mould resets.
If the problem persists, please contact
us. Additional resources may be found at
www.bluensupboards.com/info-zone/
maintenance-repair/
The weighted n enhances handling and
manoeuvrability, especially in more testing
conditions. Please securely attach your n
system to prevent loss or damage.
For a replacement n, please visit
www.bluensupboards.com
Remove the valve from the board entirely
using the valve tool provided. Pump air
through the vacant hole repeatedly for 20
minutes. Once complete, lay the board at in
a cool, dry area with plenty of ventilation for at
least 24 hours.
If the problem persists, please contact
us. Additional resources may be found at
www.bluensupboards.com/info-zone/
maintenance-repair/
TROUBLESHOOTING | 08

For the rst 6 months of the warranty, a prepaid returns label is provided by us for the
return of any faulty goods. Sadly we cannot arrange collections. After this time, it would
be the customer’s responsibility to cover the costs of the return postage, and we will
cover the cost back to you; so effectively splitting the costs.
As soon as the item is back with us and has undergone routine checks, we’ll be able to
take your case further and either exchange, repair or refund your item as agreed. Please
note, it can take up to 28 days for a return to be processed once we have received
your consignment. Refunds are only available in the rst 60 days from the start of the
warranty.
If you have simply changed your mind and wish to return your product, you have 60
days to do so but you must cover the postage back to us and return the item in an
unused condition, with all items still in their original packaging.
Once the item has been received, we will perform a quality control check to ensure the
item and its counterparts are in a new and unused condition, and only then will the
refund be processed. Any goods found to be used will be returned to the buyer.
All purchases of our boards, from 1st September 2018, come
with a 5 year manufacturer warranty to cover any manufacturing
faults, starting from the date of delivery. Any purchases before
this date will have a 1 year warranty starting from the date of
delivery. To make a warranty claim, please email:
support@bluentrading.co.uk
09 | WARRANTY

Only the board itself is covered by our 5 year warranty. The accessories are covered by
a 1 year warranty, subject to conditions. For full details, please visit:
www.bluensupboards.com/info-zone/warranty/
We cover any abnormal defects or manufacturing errors for the full 5 years and will
ensure a professional repair is carried out. In the unlikely event we cannot repair, we will
replace like for like and the warranty would not restart on the replacement. As much as
we’d like to, we sadly cannot cover the following for a warranty claim:
Boards purchased from non-authorised
Bluen retailers.
Boards purchased in used condition or with
any customer-initiated modications to the
board.
Damage or defects caused by impact with
any materials or objects (rocks, docks, other
boards, etc).
Damage or defects caused by use outside of
its intended purpose.
Damage or defects caused by normal wear
and tear.
Damage or defects caused by transport,
loading, unloading, dropping, or out of
water handling. Including marks left by over
tightening transport straps.
Damage or defects caused by heel dents also
known as pressure dings.
Damage or defects caused by inappropriate
storage in temperatures over 90°F and under
32°F.
Damage or de-lamination caused by over-
heating as a result of exposure to direct
sunlight while not in use.
Damage or defects caused by wave impact
and/or impact with ocean/lake oor.
Damage or defects caused by storage of the
board in closed, damp conditions (e.g. a wet
board bag).
Damage to n or n box caused by impact.
William Vaughan
Chief Executive
Bluen Trading Ltd, Wadsworth, Hebden Bridge, W. Yorks, UK, HX7 8TG
WARRANTY | 09

For even more support, skills,
tips and tricks, to share SUP
stories, photos and videos of
your adventures and more -
please join the Bluen SUP
Paddle Board Owners Club on
Facebook. As a member of
this ever-expanding online
community you’ll have the full
support of Bluen crew
members and board owners
just like you!
facebook.com/groups/
BluenSUPCommunity
Sign up to our newsletter for
exclusive offers and news:
www.bluensupboards.com/
sign-up/
JOIN THE COMMUNITY
Follow us @bluensups
www.bluensupboards.com