ESCALADE STIGA T8581W User manual

1.Read this manual carefully before starting assembly. Read each stepcompletely before beginning
each step.
2.Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3.If hardware is tightenedtoo soon, mounting holes may not align and partsmay not easily fit together.
Leave bolts slightly loose until you are instructedto tighten them.
4. Tools required for assembly: Wrenchesor adjustable wrenches (not provided) are helpful.
5. To make assembly as easy as possible, place all partsof the table tennis in acleared area and
remove the packaging material. Organize all parts as per parts identifier in the assembly manual.
Do not dispose of the packing material until assembly is completed.
6. Avoid scratching table tennis top and metal tube parts during the assembly process.
7. Assemble product on clean, level and flat surface.
8. Take timeto correctly orientate parts exactly as per each assembly diagram.
9.Save this instruction inthe event that the manufacturer has to be contacted for replacement parts.
OWNER’S MANUA L
Please visit our website at: www.escaladesports.com
ON-LINETROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLYASKED QUESTIONS
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMANTION
R
Escalade Sport productsmay be manufactured and/or licensed under the following patents.
6120397 , 5816957 , 5769744 , 5119741 , 4911085 , 4717157 , D460140 , D420563
Additional patentsmay be pending. One or more of the listed patents and/or pending patentsmay cover specific product.
R
2018Escalade Sports
C
R
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [e-mail]
R
READ ASSEMBLY, OPERATING AND SAFETY INSTRUCTIONS
CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED TO PUT
THIS TABLE TOGETHER!
Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as
Manufacturing defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT
TO THE STORE!
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Be sure to write your model number and serial number here
for future reference. You can find these numbers printed on
the bottom of the table.
MODEL NO.: T8581W/F
DATE CODE : CPSIA#2-T8581W/F-_______-SY
PURCHASE DATE : _______________________
Please provide model number and/or part number of the product and/or part when you call or write. These numbers can be found on the
product, packaging, and/or in this Owner’s Manual.
CAUTION:

- 2 -
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple
maintenance steps, you will add to the life of your new table.
The top (playing surface) of your table is made of Mid-Density Board. Like all productsmade of wood, it
can be affected by atmospheric changes in both temperature and humidity. This may cause a slight
sag or distortion as the top expands or contracts. This is normal and should not cause concern as it
does not detract from the play or utility value of the table. After assembly of the table, you can minimize
the effects of temperature and humidity changes by storing the table in a dry area when table is not
in use.
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes can cause the wood to warp, swell, crack or blister. When your table is not in
use, it should be stored in a dry area. Due to the nature of particle board, table top may bow.
Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
THE TABLE TOP
STORAGE OF YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table’s playing
surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING PRODUCTS on your table’s playing
surface.
CLEANING YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease
of use of your table.
MAINTENANCE OF YOUR TABLE
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING
POSITION and move table several inches in different directions to find the best location for the table.
If the floor is extremely unlevel, table may not play or operate properly.
I
The table has leg levelers - Adjust leg levelers as required.
f table is high in the center, shim up under the outer legs.
UNLEVEL FLOORS
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes which occur on patios or similar areas can cause wood to warp, swell, crack or
blister.

- 3 -
HARDWARE IDENTIFIER (To Scale)
H1 - 8 mm x 55 mm
Hex Head Bolt
(8 pcs)
H2 - 8 mm x 16 mm
Plastic Flat Washer
(16 pcs)
H3 - 8 mm Nylon
Lock Nut
(8 pcs)
PARTS IDENTIFIER (Not to Scale)
P1 - Table Tennis Table Top
Frame Assembly
(2 pcs)
P2 - Leg with Casters
Assembly
(4 pcs)
P3 - Connector
(8 pcs)
P4 - Net Post
(2 pcs)
P5 - Net (1 pc)

- 4 -
PARTS REQUIRED
1 pc P1 Table Tennis Table Top Frame Assembly 4 pcs - H1 Hex Head Bolt
2 pcs - P2 Leg with Casters Assembly 8 pcs - H2 Flat Washer
4 pcs - P3 Connector 4 pcs - H3 Lock Nut
STEP 1:
IMPORTANT NOTE: Place table half top with playing surface face down on a CLEAN flat surface
for ease of correct assembly and to prevent any scratches or blemishes to the playing surface.
-
P1
Push down on LOCK TAB
to release lock and pull up
on FRONT LEGS only.
Do not pull up middle legs
as this could cause damage
to the table.
DETAIL A
This end is the front
of the table.
This end is the middle of the table
and does not have white screen
lines and close to Safety Latch.
Front Leg.
Front Leg.
PUSH UP
Hinge Locked
Safety Lock.
FIGURE 1B
FIGURE 1A
DETAIL B
Lay one piece P1 Table Tennis Table Top Frame Assembly flat with playing surface
facing down as shown in FIGURE 1A.
Unlock the SAFETY LOCK as shown in DETAIL A and raise FRONT LEGS to a
vertical position and lock both hinges as shown in FIGURE 1B & DETAIL B.
Install P2 Leg with Casters Assembly with P3 Connectors using
H1 Hex Head Bolts, H2 Flat Washers and H3 Lock Nuts
as shown in FIGURE 2 &DETAIL C. Tighten this hardware.
Repeat procedure for other table top.
STEP 2:
P2
P3
H1
H2
H2
H3
FIGURE 2
DETAIL C
Middle Leg.

- 5 -
Attach one P4 Net Post to the middle edge of where the table halves meet.
Repeat this with other P4 Net Post on opposite side.
Then, slide P5 Net into corresponding P4 Net Post and repeat for the other side.
Make sure the white fabric of the net is on top. Use strings at either end of the P5 Net to tighten the net and attach to base of net post
securely.
STEP 3:
PARTS REQUIRED
2 pcs - P4 Net Post
1 pc
WARNING:
THIS STEP REQUIRES TWO OR MORE ADULTS.
VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON
ITS LEGS. BE CAREFUL, THE TABLE IS VERY HEAVY.
- P5 Net
FIGURE 3
NOTE:
Level table using
Leg Levelers.
IMPORTANT NOTE:
Be sure to break all four(4) hinges, using the palm
of your hand before folding table upright.
Lock hinges when table is in playing positions.
P4
Net Post
P4
Net Post
P5
Net

- 6 -
CAUTION:
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO
NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON
TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS
TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY OR
PROPERTY DAMAGE.
FOLD THE TABLE:
1. Remove the Net Set and push hinges up as shown in FIGURE 4.
2. Fold each half table as shown in FIGURE 5.
3. Secure table into upright position as shown in FIGURE 6.
REMOVE NET SET
FIGURE 4
FIGURE 5 FIGURE 6
UNFOLD THE TABLE:
1. Push down on Lock Tab to release lock as shown in FIGURE 7.
2. Fold each half table as shown in FIGURE 8.
3. Push down and lock hinges as shown in FIGURE 9.
PUSH UP
PUSH UP
ATTACH NET SET
FIGURE 9
FIGURE 8
PUSH DOWN
PUSH DOWN
Unfold the table
Push down
on Lock Tab
FIGURE 7

- 7 -
C1 Leg Leveler
C2
Caster with Lock
C3L
Left Hinge
C3R
Right Hinge
P1
P2
P3
H1
H2
H3
H2
DETAIL - A
DETAIL - B
DETAIL - C
DETAIL - E
C4
H2
C6
H2
C8
C4
H2
H2
C8
C6
P4
P5
C11
Front Leg with Panel
C13
Linkage
C12 Middle Leg
C9
C5
C5
C8
C10
C10 C8 C5
C5 C9
C10
DETAIL - D
C7
C7

- 8 -
T8581 TABLE TENNIS TABLE SPARE PARTS
.oNtraP#yeK Description Qty
H1 T85 SY-H1 8
H2 T85 SY-H2 16
H3 T85 SY-H3 8
P1 T85 SY-P1 2
P2 T85 SY-P2 4
P3 T85 SY-P3 8
P4 T85 SY-P4 2
P5 T85 SY-P5 1
C1 T85 SY-C1 4
C2 T85 SY-C2 8
C3R T85 SY-C3R 2
C3L T85 SY-C3L
8 mm x 55 mm Hex Head Bolt
8 mm x 16 mm Plastic Flat Washer
8 mm Nylon Lock Nut
Table Tennis Table Top Frame Assembly
Leg with Casters Assembly
Connector
Net Post
Net
Leg Leveler
Caster with Lock
Right Hinge
Left Hinge 2
DETAIL A
C4 T85 SY-C4 4
H2 T85 SY-H2 8
C6 T85 SY-C6 4
C8 T85 SY-C8
8 mm x 90 mm Hex Head Bolt
8 mm x16 mm Plastic Flat Washer
8.5 mm x 19 mm x 15 mm Long Spacer
8 mm Nylon Lock Nut 4
DETAIL B
C9 T85 SY-C9 4
C5 T85 SY-C5 8
C8 T85 SY-C8 4
C7 T85 SY-C7
DETAIL C
C10 T85 SY-C10 3.5 mm x 14 mm Phillips Round Head Screw 16
DETAIL D
DETAIL E
C4 T85 SY-C4 4
H2 T85 SY-H2 8
C6T85 SY-C6 4
C8 T85 SY-C8
8 mm x 90 mm Hex Head Bolt
8 mm x 16 mm Plastic Flat Washer
8.5 mm x 19 mm x 15 mm Long
Spacer 8 mm Nylon Lock Nut 4
C11 T85 SY-C11 Front Leg with Panel 2
C12 T85 SY-C12 Middle Leg 4
C13 T85 SY-C13 Linkage 4
K1 T85 SY-K1 Hardware Kit 1
M1 T85 SY-M1 Owner’s Manual 1
4
C10 T85 SY-C10
8 mm x 60 mm Hex Head Bolt
8.5 mm x19 mm x 4 mm Step Bushing
8 mm Nylon Lock Nut
Steel Leg Bracket
3.5 mm x 14 mm Phillips Round Head Screw 32
C9 T85 SY-C9 4
C5 T85 SY-C5 8
C8 T85 SY-C8 4
C7 T85 SY-C7 4
C10 T85 SY-C10
8 mm x 60 mm Hex Head Bolt
8.5 mm x 19 mm x 4 mm Step Bushing
8 mm Nylon Lock Nut
Steel Leg Bracket
3.5 mm x 14 mm Phillips Round Head Screw 32

- 9 -
90 DAY LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product
(hereinafter referred as the “Product”).
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of
ninety (90) days from the original purchase.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS shall
repair or replace withacomparable model, and Product, or component thereof, which may prove
defective under normal use and proper care, and which our examination shall disclose to our
satisfaction to be thus defective, please contact our Warranty Dept.
R
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any
Product of its manufacture is free from defects in material and workmanship when used for the intended
purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED
BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS
PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND
R
WORKMANSHIP.
R
1-866-873-3528 / Warranty Dept.
Or Write us at:
Escalade Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[e-mail]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty
Products. ESCALADE SPORTS strongly recommends that the Product is insured for value prior to mailing.
R
R
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE ABOVE NINETY (90) DAY WARRANTY PERIOD. ESCALADE SPORTS SHALL
NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS,
EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
R
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty give you specific legal rights and you may also have other rights which
may vary from state to state.