BlueTrek CRESCENDO - User manual

VOICE
User guide
Enjoy the ultimate voice control headset.
You only need to say. No voice training required. Let’s start !
Dual mic noise cancellation bluetooth® headset

English
BLUETREK CRESCENDO I 1
Get started...
∙ Fully charge your headset for 2 hours.
∙ Select the ear bud and ear hook that fit for your ear.
∙ Wear the headset.
∙ Press the main button for 5 sec.
You will hear the welcome message :
“Hi, Welcome to the Bluetrek Crescendo
headset with the BlueGenie Voice Interface.
To get started you’ll need to pair your headset.
Click the main button to enter pair mode.”
∙ Follow the instruction, press the main button to entry to the pair mode.
∙ Enable the Bluetooth® search function on your device. Select “Bluetrek Crescendo” and
enter “0000” as the passcode.
∙ To use voice control, press the Main Button, wait for the “Say a command”
prompt to finish, then say your command.
∙ At any time you can use the “What Can I Say” command to be remember the available
commands.

English
2 I BLUETREK CRESCENDO
Special Commands to access FREE service in USA
You can say “Call Information” to search for local and business listings with
Bing™ 411. Find news, directions, restaurant locations, weather forecasts,
movie showtimes, and more.
You can say “Traffic Conditions” to connect to local 511 services to check
traffic condition in USA. For example, road work, traffic jam, accident
information etc...
Simply set up your speed dial list for customized number
Set up your Speed Dial List Speed Dial Position Contact to assign
(Please refer to your
phone’s User Manual to
learn how to input them
and program as this table.)
1
2
3
4
5
6
7
Favorite 1 / voice mail
Favorite 2
Favorite 3
Favorite 4
Favorite 5
Home
Office

English
BLUETREK CRESCENDO I 3
Voice Command
The following is a comprehensive list of the available commands.
At any time you can use the “What Can I Say” command to listen the available commands.
Tell you all available commands
Enter the pairing mode
Tell you if connected to a phone
Enter voice recognition function
(if mobile phone support)
Tell you the status of the headset’s battery level
Dial the last dialed number
Dial the last received number
Connect to Microsoft’s Bing Search Center
Command Say this to...
What Can I Say?
Pair Mode
Am I Connected?
Phone command
Check Battery
Redial
Call BackCall
Information

English
4 I BLUETREK CRESCENDO
Call Voice mail/ Favorite 1
Call Favorite 2
Call Favorite 3
Call Favorite 4
Call Favorite 5
Call Home
Call Office
Traffic Conditions
Answer
Ignore
Settings Menu
Cancel
Yes
No
Call number preset on Speed Dial 1
Call number preset on Speed Dial 2
Call number preset on Speed Dial 3
Call number preset on Speed Dial 4
Call number preset on Speed Dial 5
Call number preset on Speed Dial 6
Call number preset on Speed Dial 7
Connect to local 511 center for Traffic conditions
Answer the incoming call
Reject the incoming call
Enter to setting menu
Cancel the active operation
Answer “yes” for yes/no question
Answer “no” for yes/no question

English
BLUETREK CRESCENDO I 5
Multi-point function
BLUETREK Crescendo supports multipoint technology, which allows you to use one
headset with two different Bluetooth mobile phones. Please see the instructions as below:
Enable the multi-point function
1. Pair the headset to the mobile A (Please refer to “pairing” section).
2. Long press the Vol + and the Vol - button together on the headset under stand-by mode,
when heard a “beep”, release the buttons and you will hear “Multi-point on” prompt to
finish, the multi-point function will be enabled.
3. Press Main button and the Vol - button together to reset the hardware, the headset will
turn off automatically.
4. Press and hold the Main button for about 5 seconds to enter into pairing mode, then pair
it to the mobile B.(Please refer to “pairing” section).
5. Turn off and turn on again the headset. The 2 mobiles will be connected automatically.

English
6 I BLUETREK CRESCENDO
Disable the multi-point function
Long press the Vol + and the Vol - button together on the headset under stand-by mode,
when heard a “beep”, release the buttons and you will hear “Multi-point off” prompt to
finish, the multi-point function will be disabled.
Answer a call while talking on the other paired phone
• To answer the second call and put the current call on hold, double press the Main button to swap
• To answer the second call and terminate current call , press once on the Main Button
• If reject the second call, press the Main Button for 2 seconds
* To avoid issues switching between calls, suggest use the call control button on the
headset rather than your phone controls.

English
BLUETREK CRESCENDO I 7
Setting menu
Under setting menu, you can set.
“Say a command prompt “- Enables or Disables the “Say a command prompt”. With it
disabled, you will hear a beep instead of voice command.
∙ Incoming call announce - Enables or Disable the Incoming call ID prompt and voice
answer functions (this function may not available on some phones).
∙ Save favorite - A phone number can be saved on the headset after you received an incoming call.
∙ Voice control help
∙ Turn off voice control - Turns off the voice control. To re-enable, hold the “Vol+” and
“Vol-“ button simultaneously for about 6 seconds.
Reset the Crescendo headset
If the headset fail to communicate or any abnormal behavior, you may need to reset your
headset. Reset the headset will deletes all pairing information, reset the voice interface and
reboot headset back to pairing mode.
To reset your headset, press main button together with “Vol +” for 6 sec until the red LED flashes.

English
8 I BLUETREK CRESCENDO
Control the headset by button
Function
Power On
Power Off
Enter Pairing Mode
Activate Voice control
Answer Call
Reject Call
End Call
Redial
Volume adjust
Mic Mute On/Off
Turn Voice Control On
Software Reset
Hardware Reset
Button
Main button
Main button
Main button
Main button
Main button
Main button
Main button
Main button
Vol + / Vol -
Vol + / Vol -
Vol + & Vol -
Main button & Vol +
Main button & Vol -
Time
5 sec
7 sec
7 sec
Press once
Press once
3 sec
Press once
Double click
Press once
3 sec
6 sec
7 sec
Press once
Status
From off
From on / Standby
From off
Idle / Pairing / Standby
(when voice control on)
Ringing
Ringing
Active call
Standby (Connected)
Active call / standby
Active call / standby
Pairing / standby mode
Pairing / standby mode
Any status

English
BLUETREK CRESCENDO I 9
More information and Support
This user manual is just to get you started.
If you are having trouble, visit www.bluetrek.com to download the user manual , which
has full details of all features and functions.
Features may vary depending upon your mobile phone . You can check the compatibility
on our website. You can also check with your phone manufacturer that your handset
supports either handsfree or headset Bluetooth profiles.
Visit our website and check for available firmware updates. Please read the procedure
carefully before updating the firmware.
Please contact us before returning the product to your dealer and we will help you through
any difficulty you may have.