BlueTrek UFO User manual

Before using your headset for the first time, you must charge it continuously for about 4
hours, until the red indicator light turns off. Please refer to the“Charging the BLUETREK®
UFO”section of this manual.You also have to pair the headset with a mobile phone.
Please refer to the“Pairing the BLUETREK® UFO”section of this manual.
A built-in voice alert is an advanced feature that is now available on your headset. A
recorded voice reminds you of the actions in your headset, such as: redial the last number,
reject a call, call your favourite number, when your headset needs to be charged
and if your headset is connected/disconnected from the handset.
You may choose to activate /inactivate this function by pressing both talk button and Vol+
for 3 seconds then switch on your headset again.
1 I BLUETREK UFO
English
Introduction
The BLUETREK® UFO headset is a wireless headset based on the Bluetooth® technology. It
complies with Bluetooth® 1.2 protocol, supporting Headset and Hands-free profile.
TALK button
VOL+ button
Pre-registered number 1
Indicator light
Pre-registered number 2
VOL- buttton
Charging socket
12
6
3
5
1
2
3
4
54
6
77

Charging the BLUETREK® UFO
Please connect the charger to the headset and to the main. During the charge, the
indicator light is red. The indicator light will turn off when the charge is complete.
During subsequent charges, the charging should take approximately 3 hours.
When you hear a low-tone beep (or the voice alert if activated) in your headset at regular
intervals, and the indicator light flashes in red, your headset needs to be recharged.
Important:
· If your headset is fully charged, the red indicator light will not turn on when plugging
into the charger.
(To check whether your headset is fully charged, press the talk button for approx.
2 seconds, once released, the red indicator light will turn on for approx. 3 seconds.)
· To maximize battery lifetime, it is recommended to recharge your headset to full capacity
only when the battery is low, since a battery has a lifetime of about 500 charging cycles.
· If you leave your headset battery empty for an extended period of time, it could
excessively discharge the battery. In this case, charge your headset for 3 hours or more
until the battery recovers and recharges completely.When you first charge the headset
after prolonged storage, it may take few minutes for the red indicator light to turn on.
· Do not charge your headset for more than 10 hours.
· The use of any other charger will automatically suspend the warranty. It is strictly
forbidden and can be very dangerous.
BLUETREK UFO I 2
English

Pairing the BLUETREK® UFO
Before using the BLUETREK® UFO headset, you must pair it with your Bluetooth® mobile
phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can communicate.
To initiate pairing:
Place the BLUETREK® UFO and your mobile phone within 0.3 meter (1 foot) from each
other.
3 I BLUETREK UFO
English
1
2
4
3
Switch on your phone and select its Bluetooth® discover
mode (refer to the Bluetooth® mobile phone user manual).
When the BLUETREK® UFO is switched
off, press and hold the TALK button for
about 7 seconds until the indicator light
flashes red and blue alternately. And a
sound can be heard in the speaker.
Once the mobile phone detects the headset, a“BLUETREK UFO”message
will be displayed. Follow the phone instructions to accept the pairing.The PIN
code (or passkey) is 0000, then press“yes”or“ok”.

BLUETREK UFO
“0000”
BLUETREK UFO
BLUETREK UFO
5
BLUETREK UFO
Connect
Assign short name
Set as unauthorised
Delete
Select Cancel
If pairing was successful, the indicator light will switch to blue and flashes slowly.
If you haven’t started the discovery mode within 5 minutes, the headset will go to the
standby mode. You must then switch off your headset and start the pairing again.
English
For some phones, you may need to select“Connect”.
BLUETREK UFO I 4

Wearing the BLUETREK® UFO
5 I BLUETREK UFO
English
RL
Two different sizes of metal ear hooks and plastic ear hooks are included in the pack to
suit your ear size. (Note:The ear hook is non-adjustable and non-rotatable.The warranty
will be suspended if the ear hook hinge is damage.
To attach the ear hook, simply insert the
ear hook ring to the back of the headset
gently as shown in the diagram.
For left ear wearing, the ear hook should
be inserted from the right hand side.

Switching the BLUETREK® UFO ON and OFF
Switching BLUETREK® UFO ON
When your headset is off, press and hold the TALK button for about 3 seconds until the
blue indicator light is on. A beep (2 tones) can be heard in the speaker. Release the
TALK button.
Switching BLUETREK® UFO OFF
When your headset is on, press and hold the TALK button for about 7 seconds until the red
indicator light is on. A beep (2 tones) can be heard in the speaker then release the TALK
button.
Making a call
Mobile phone with voice recognition
. Make sure the voice recognition function on your mobile is activated and your voice tags
have been recorded with the phone.To enter these, please refer to your phone’s manual.
.When there is no incoming or active call, press once on the TALK button
.Wait for the audio signal sent by the mobile phone (generally a short tone).
. Speak the name of person you wish to call.
Mobile without voice recognition
. Make sure both the headset and the mobile phone are ON and in stand-by mode.
. Dial the number on the phone keypad, after approximately 2 seconds the audio
connection will be established.
This function may not be available on some phones, please refer to the trouble shooting
frequent asked questions in our website: www.bluetrek.com. to find out more.
English
BLUETREK UFO I 6

Answering a call
When the headset rings, press once on the TALK button to take the call.
Ending a call
Press once on the TALK button to end an active call.
Adjusting the volume
To increase the volume during an active call, press the “VOL+”button on the headset.
To decrease the volume during an active call, press the “VOL-“ button on the headset.
7 I BLUETREK UFO
English

Muting the microphone
To mute the microphone during an active call
During an active call, press and hold the VOL+ button for approximately 3 seconds. A
periodic tone can be heard in the speaker when the microphone is muted.
To end the mute function
When the microphone is muted, press and hold the VOL+ button on the BLUETREK® UFO
for approx. 3 seconds.The periodic tone will end.
Transferring a call from BLUETREK® UFO to the mobile phone
During an active call, double click on the TALK button.
This function only works in the Hands-Free Profile.
In the Headset profile, you can simply turn off your headset.
Transferring a call from the mobile phone to the BLUETREK® UFO
During an active call on the mobile phone, press once on the TALK button to transfer the call.
This function may not be available depending on your phone.
English
BLUETREK UFO I 8

9 I BLUETREK UFO
English
Pre-registered numbers feature
-This feature allows you to store your 2 favourite numbers in your BLUETREK® UFO
headset and to dial these numbers directly from your headset.
(Important:This feature is only available in the Hands-free profile).
Storing your favourite numbers
1) Ensure your BLUETREK® UFO headset is paired and connected with your phone.
2) Enter numbers following the syntax describe below as your mobile phone name
(Please refer to your mobile phone manual to change your phone name. In most phones,
the mobile phone name is under the“Bluetooth”menu)
XSXXXXXXXXT
The number you wish to store,
in national or international
format, with maximum of 15
digit.
Either “1”or “2”,
depending on which
position you want the
number to be stored.
Fill in the letter“S”
Fill in the letter“T”
Example 1:To store“0123456789”in position 1 = 1S0123456789T
Example 2:To store“[phone]”in position 2 = 2S+44123456789T

English
BLUETREK UFO I 10
3) Press and hold the“Vol-“ button on your BLUETREK® UFO headset for approx. 3 seconds,
until the purple indicator light is on. (A beep can be heard in the speaker).
4) If the number is correct and have stored in the headset, you will hear:
1 beep in the speaker and the blue indicator light will flash once if the number has been
stored in position 1.
OR
2 beeps in the speaker and the blue indicator light will flash twice if the number has been
stored in position 2.
If the number is incorrect, it will not store in the headset.You will hear a long low-tone beep
in the speaker and the red indicator light will flash twice.
Note:
- Only 1 telephone number can be stored at one time.To store the second number,
simply repeat from Step 2.
- Maximum of 2 favourite numbers can be stored and can be replaced by repeating the
above steps.
- Remember to change back your mobile phone name once you have stored the numbers.
1) Ensure your BLUETREK® UFO headset is paired and connected with your phone.
2) Press once on the pre-registered number 1 or pre-registered number 2 to call one of the
stored numbers on your BLUETREK® UFO headset:
-1 beep (or the voice alert if activated) to call your number stored in position 1;
-1 beep (or the voice alert if activated)to call your number stored in position 2.
Making a call to one of the stored numbers

Additional features with some phones
Rejecting a call
Press the TALK button for about 2 seconds to reject a call.
Redial the last number
When there is no incoming or active call, press the TALK button for about 3 seconds until
you hear a beep (or the voice alert if activated).
Troubleshooting guide
The first thing you should do when encountering a problem that you cannot solve with this
manual, is to switch off your headset and your mobile phone, and switch them on again.
To find out more, please refer to the trouble shooting frequent asked questions in our
website: www.bluetrek.com.
11 I BLUETREK UFO
English

Guidelines for safe use
Read those guidelines before using your headset.
- The volume level of the Bluetooth® headset may vary, depending on your mobile phone.
Before using your headset for the first time, adjust the headset volume to the lowest, then
increase the volume gradually until you reach to an acceptable level.
High levels of volume may result in hearing loss, avoid using the headset at high volume
continuously. If you experience ringing in your ears or muffled speech, consult your doctor
immediately and stop using the headset.
- Do not drop or try to alter the shape of your headset.
- Do not expose your headset to liquid or moisture.
- Do not expose your headset to extreme temperatures.Temperature range : 0-40oC.
- Do not expose your headset to fire or open flames.
- Do not try to disassemble your headset. Service and Maintenance can only be performed
by authorized BLUETREK® dealers.
- Keep your headset away from dust and dirt.
- Do not let children play with your headset, since it contains small parts that could become
detached and create a choking hazard.
- Check the regulation in your area if you plan to use your headset while driving.
- Turn off your headset before boarding an airplane.
CAUTION :The built-in battery is non-replaceable. Do not attempt to replace it. Danger of
explosion if battery is incorrectly replaced. Dispose of batteries according to local
regulations. Do not dispose as household waste.
English
BLUETREK UFO I 12