BN Products BNH-640 User manual

Page | 1 BN Products-USA
www.bnproducts.com
MODEL: BNH-640
ROTARY HAMMER
OPERATOR MANUAL
Read this Manual carefully before operating this tool.
is Manual includes important Tool Safety warnings. Failure
to follow instructions may result in electrical shock, re and/or
serious personal injury.
3450 N. SABIN BROWN ROAD • WICKENBURG, AZ 85390
[phone] • [e-mail]
BNH-640-Operator-Manual.indd

Page | 2 BN Products-USA
www.bnproducts.com
ROTARY HAMMER OPERATOR MANUAL
ank you for choosing our BNH-640 Electric Rotary Hammer. is manual
covers the proper operation and maintenance. Before operating, please read this
manual carefully for important procedures and safety.
All technical data and drawings in this manual are consistent with information
on this product. However, as a result of revisions and other ongoing updates, the
contents of this manual may be slightly dierent from the actual product. BN Prod-
ucts-USA, LLC. reserves the right to make changes at any time, without notice.
e copyright of this instruction manual belongs to BN Products-USA, LLC. No
reproduction is allowed without the written consent of:
BN Products-USA, LLC. All rights reserved.
is manual is a permanent part of this tool
and should accompany the product if it is resold.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of
ammable liquids, gases, or dust. Power tools create sparks which may ignite the
dust or fumes. Do not use the device in wet or humid environment. Keep children
and bystanders away while operating the machine. Distractions may cause you to
make lose control of the device.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with grounded power tools. Modied plugs and
matching outlets will increase risk of electric shock.
• Avoid bodily contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. ere is an increased risk of electric shock.
• Do not expose power tools to rain or wet conditions. Moisture entering a
power tool will increase the risk of electric shock.
• Do use a damaged cord. Never use the cord for carrying or pulling the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
tangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for
outdoor use only

Page | 3 BN Products-USA
www.bnproducts.com
PERSONAL SAFETY
• Stay alert when operating a power tool. Do not use a power tool while you are
tired or under the inuence of drugs, alcohol or medication.
• Avoid unintentional running of the tool. Ensure the switch is in the o-posi-
tion before connecting to power source, picking up or carrying the tool.
• Remove any adjustment key or wrench before turning the power tool on. A
wrench or a key le attached to a rotating part of the power tool may result in
personal injury.
• Do not overreach. Keep proper footing and balance at all times. is enables
better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, cloth-
ing and gloves away from moving parts. Loose clothes, jewelry or hair can be
caught in moving parts.
• If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these devices
can reduce dust related hazards.
• Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing pro-
tection used for appropriate conditions will reduce personal injuries.
POWER TOOL USE AND CARE
• Do not force the tool beyond its capabilities. Use the correct power tool for
your application. e correct power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and o. Any power
tool that cannot be controlled with the switch is dangerous and must be re-
paired.
• Store power tools out of the reach of children and do not allow persons unfa-
miliar with the tool or these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
• Perform periodic maintenance for all tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition that may aect the
power tool’s operation. If damaged, have the power tool repaired before use.
Accidents can be caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc., in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations dierent from intended could
result in a hazardous situation.

Page | 4 BN Products-USA
www.bnproducts.com
SERVICE
Have your power tool serviced by a qualied repair person using only genuine
replacement parts. A parts guide is available for this tool at BNProducts.com. Con-
tact BN Products-USA™ Customer Service at [phone] if you need assistance
from a qualied professional service department.
ROTARY HAMMER SAFETY
• Use the auxiliary handle, supplied with the tool, for stability. Make sure that
the handle is in a clear and comfortable position for using the Rotary Hammer.
• Wear a dust mask. Do not inhale particulate matter generated in drilling or
chiseling operations.
• Before beginning work, always check the working area to ensure that no con-
cealed electric cables or gas and water pipes are present.
• If the power cord is damaged, it must be replaced to avoid risk of electric
shock.
• Do not touch the bit during or immediately aer operation. e bit becomes
very hot during operation and could cause serious injury or burns.
• Moderate operational time while using the Rotary Hammer to minimize risks
related to vibration of the tool. If you lack sensation due to vibration or are
fatigued, resume activity only aer rest.
• Only use SDS-Max bits, which are designed for this tool. Do not use a y cut-
ter with this tool, as the attachment will be damaged and may create projectile
hazards.
• Ensure that the sha of the tool has come to a complete stop before touching
the chuck or attempting to change a chisel or bit.
• A chisel or drill bit must be rmly and correctly seated and secured in the
SDS-Max chuck before beginning operation of the Rotary Hammer.
VIBRATION SAFETY
• Constant exposure to vibration has been known to cause serious health prob-
lems such as back pain, carpal tunnel syndrome, and vascular disorders.
• Include vibration-free periods during the work day.
• Avoid excessive gripping of the tool; the Rotary Hammer should be gripped as
lightly as possible while still keeping full control.

Page | 5 BN Products-USA
www.bnproducts.com
SPECIFICATIONS
Model Number BNH-640
Electrical Rating 120V-60Hz | 10.4A | 1250 Watts
No-Load Speed 0-480 RPM
Impact Rate 1500-3100
Impact Energy 2-9J (1.5-6.6 -lbf)
Chuck Type SDS-Max
Maximum Drilling Capacity Drill Bit: Ø40mm (1-9/16”)
Weight 16.5 lbs. (7.5 kg)
Dimensions (LxWxH) 18-1/4” x 4-3/4” x 10-3/4”
(46.5 x 12.1 x 27.5 cm)
SETUP
Read the entire safety information section at the beginning of this manual.
To prevent serious injury from accidental operation: Turn the Power Switch o,
and unplug the tool from any electrical outlet before assembling or making any
adjustments to this machine.
ACCESSORIES & CARTON CONTENTS
BNH-640 Rotary Hammer (1) Wrench (1)
SDS-Max Chisel 18 x 320mm (1) SDS-Max Drill Bit 18 x 320mm (1)
Lubricant Tube (1) Auxillary Handle (1)
Carbon Brush Set (1)