Bob's Discount Furniture MONTANA YOUTH User manual

Thank you for purchasing this quality product. Be sure to check all packing materials carefully
for small parts that may have come loose inside the carton during shipment.
***Caution: Please read all instructions carefully before starting the assembly process. These
parts are cumbersome and heavy. Therefore, two people are recommended in order to
prevent personal injury and insure the parts are not damaged during the assembly.
ALWAYS US GUARDAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK BED WILL BE PLACED
NEXT TO THE WALL, THE GUARDRAIL RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST
THE WILL TO PREVENT ENTRAPMENT BETWEEN THE BED AND WALL.
Prohibit more than one person on upper bunk. Upper bunk load capacity: 226.7kg / 500 lb.
Lower bunk load capacity: 362.8kg / 800 lb.
* Follow the information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
* Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of
entrapment or falls.
* Surface of mattress must be at least 12.7 cm / 5 in below the upper edge of guardrails.
* Do not allow children under 6 years of age to use the upper bunk.
* periodically check and ensure that the guardrail, ladder and other components are in their proper position,
free from damage and that all connectors are tight.
* Do not allow horseplay on or under the bed and prohibit jumping on the bed.
*Always use the ladder for entering and leaving the upper bunk.
* Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
*Use of a night light may provide added safety precaution for a child using the upper bunk.
* Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall,
the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment
between the bed and wall.
* The use of water or sleep flotation mattress is prohibited.
STRANGULATION HAZARD:
* Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for
example, but not limited to, hooks, belts, and jump ropes.
* Prohibit more than one person on upper bunk.
* keep these instructions for future reference.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 1/2" - 38 1/2" in width and 74" - 75" in length on upper bunk, and lower bunk.
The total thickness of mattress must not exceed 7"
Note: there must be at least 5" from mattress sleeping surface to top edge of guardrail.
SAFTEY WARNING
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT OR FALLS
Assembly Instructions
Bunk Bed

Code Q'TY
a32 PCS
b4 PCS
c1 PC
d14 PCS
e2 Pc
f4Pcs
g32Pcs
STEP 1 STEP 2
STEP 3
STEP 4
Hardware List
Screw # 8*19mm
Pin 110*12*12mm
Barrel Nut 5/16"*12*15mm
Bolt 1/4"*15*32mm
Bolt 5/16"*15*95mm
Screw # 8*25mm
Allen Key 4x74x29mm
Attach the guard rail center plate to the bunk
bed rails and long guard rails by using bolt "b",
and Screw "d". (on other side too)
Attach the bunk bed rails to
the bottom Ends by using bolt
"a" and barrel nut "g"
.
Attach the slat roll to the
rails by using screw "d".
Attach the bunk bed rails and long guard rails
to the top Ends by using bolt "a" and barrel
nut "g".

STEP 5 STEP 6
STEP 7
Assembly Completed
Attach the slat roll to the rails by using screw
"d".
Attach top bed and bottom bed by using pin
"f".
Hang the ladder on the top rail, then secure the ladder
by using screw "e" from inside of the rail.

Thank you for purchasing this quality product. Be sure to check all packing materials carefully
for small parts that may have come loose inside the carton during shipment.
***Caution: Please read all instructions carefully before starting the assembly process. These
parts are cumbersome and heavy. Therefore, two people are recommended in order to
prevent personal injury and insure the parts are not damaged during the assembly.
STEP 1 STEP 2
STEP 3
Code Q'TY
a36 PCS
b7 PCS
c2 PCS
d8 PCS
e1 PC
f8 PCS
g8 PCS
Assembly Instructions
Trundle
Sping washer 1/4" *14*2 mm
Screw # 8*12mm
Bolt∮1/4"*15*13mm
Hardware List
Metal Plate 70*40*2mm
Caster 58x40x64mm
Allen Key 4x74x29mm
Screw #8*25mm
Conect the L-metal plate in the
front & back panels to the side
panels as shown by using
Turn the trundle upside
down and assemble by
using screw "f".
Assembly Completed
Attach two bottom panel by metal
plate "c", and attach the casters
"b" to the bottom of the storage
trundle unit by screws "a".