Body Craft VR-Bracket User manual

Owner’s Manual
1
VR-Bracket for Rowers
To see in
FULL COLOR
& additional information,
scan this QR code.
Assembled Parts List - VR Bracket
VR-Bracket v1.3
ALLEN WRENCH
6mm
PHILLIPS SCREWDRIVER #2
w/ Magnetic TIP
TORQUE WRENCH 3/8 DRIVE
w/ 13mm SOCKET
THE FOLLOWING TOOLS ARE RECOMMENDED FOR ASSEMBLY:
WRENCH 13mm
Part # Assembly Parts List QTY
VR-Bracket-001-ASM Main Frame Assembly 1
VP-Bracket-007 Support Bracket, Bottom 1
VP-Bracket-008 Bolt, Allen Head, M8 x 20mm L 4
VP-Bracket-009 Nut, Nylon Lock, M8 x 1.25 P 4
VR-Bracket-010 Cable Clip Mount 5

Product Assembly
STEP 2: Install Hexagon Sleeve
a. Insert the correct Hexagon Sleeve into the handlebar tube, aligning the
hole to match the side of the Cap Screw during STEP 3a.
● SPX or SPX-Mag use part #10a (larger Hexagon Sleeve)
● SPR or SPT-Mag use part #10b (smaller Hexagon Sleeve)
2
b. Then continue by installing the Main Frame
Assembly (01-ASM) into the Hexagon Sleeve
(10a or 10b).
c. Confirm the Main Frame Assembly (01-ASM)
inside the tube, is not extended out past the
“Max” line marked on top of frame.
STEP 3a: Securing Frame
Secure both the Hexagon Sleeve (10a or 10b) and the Main
Frame Assembly (01-ASM) to the handlebar tube using the
existing Cap Screw (M5 x P1.0 x 10mm L ) (A) from STEP 1.
NOTE: Double confirm the Cap Screw is tightened down to
withstand vigorous training usage.
STEP 3: Install Connect-22
Secure the Connect-22 (Connect-22-001) to the
Main Frame Assembly (01-ASM) using the hardware
pre-attached to the back of the Connect-22 (Connect-22-001):
● 4: Flat Washers (M5)
● 4: Lock Washers (M5)
● 4: Philips Head Screws (M5 x 1.0p x 15mm L)
NOTE: Double confirm the Screws are tightened down to withstand vigorous usage.
01-ASM
STEP 1: Install Main Frame Assembly
a. Place the Main Frame Assembly (01-ASM) into the
top of the Computer Arm.
b. Then place the Support Bracket, Bottom (007)
under the Computer Arm.
c. Secure the Main Frame Assembly (001-ASM) to the
Support Bracket, Bottom (007) with the follow
hardware:
i. 4: Bolts, Allen Head, M8 x 20mm L (008)
ii. 4: Nut, Nylon Lock, M8 x 1.25 P (009)
STEP 2 – “Torque Time” Tighten the Nuts, Nylon Lock
(009) to the Recommended Torque Specs of 20 ft-lbs (+/- 2 lbs).
STEP 4: Power Supply & Back Cover
Install the Power Supply (Connect-22-005) then the
Back Cover (Connect-22-011) to the Connect-22
(Connect-22-001) using the follow hardware that was
pre-attached:
● 1: Philips Head Screws (M3 x 6mm L)
NOTE: Back Cover not required, only for cosmetic.
TORQUE WRENCH 3/8 DRIVE
THE FOLLOWING TOOLS ARE RECOMMENDED FOR ASSEMBLY:
20 ft-lbs
+/- 2 lbs
Recommended Tool:
PHILLIPS SCREWDRIVER #2
w/ Magnetic TIP
ALLEN WRENCH
6mm
WRENCH 13mm
Recommended Tools:
PHILLIPS SCREWDRIVER #2
w/ Magnetic TIP
WRENCH
13mm
ALLEN WRENCH
6mm
NOTE: Confirm the Screws are tightened down to withstand vigorous usage.

3
Product Assembly - Connect-22 Cable Routing per Machine
STEP 5: How to install Cable Clip Mounts
a. Clean surface with mild spray soap or a window
cleaner and dry with a 100% cotton rag.
b. Take adhesive strip off back of Cable Clip Mount.
c. Place Cable Clip Mount and hold for 15 seconds.
d. Install Cable under clip while gently holding the back.
NOTE: DO NOT over stretch clip mount opening. Only open
enough to gently slide the cable under the mount.
STEP 6: Install Cable Clip Mounts
a. Install a Cable Clip Mount at each arrow location on the
top left side of shroud in case of any service issues.
b. Then fully install the cable with the 2.5mm power cord end
at the Connect-22 back plug. Follow the Cable Clip
Mounts with the cable to the base of the Rower.
NOTE: If you have downloaded this document, zoom-in to see the light blue arrows and their locations.
Power Supply w/ cable to base
of handlebar, (Connect-22-005), 1 each
Power Cord to Power Supply,
(Connect-22-006), 1 each
CAUTION: It is highly suggested to follow the steps below to secure the cable
away from moving parts. Do not let the cable dangle straight down to the floor.
Power Tele-Cable from base
of handlebar to Connect-22,
(Connect-22-007), 1 each
Parts from the Connect 22 (items below are not to scale)
Connect-22 22" Screen Unit
(Connect-22-001), 1 each

Detailed Parts List & Parts Exploded View
Part # Detailed Parts List QTY
VP-Bracket-001 Main Frame 1
VP-Bracket-002 Universal Joint 1
VP-Bracket-003 Vesa 100 Bracket 1
VP-Bracket-004 Bushing 4
VP-Bracket-005
Flat Washer, M8 x 2.0mm T x
23mm OD 1
VP-Bracket-006 Bolt, Allen Head, M8 x 60mm L 1
VP-Bracket-007 Support Bracket, Bottom 1
VP-Bracket-008 Bolt, Allen Head, M8 x 20mm L 4
VP-Bracket-009 Nut, Nylon Lock, M8 x 1.25 P 6
VR-Bracket-010 Cable Clip Mount 5