BOERPLAY Double Swing 1 toddler seat H2.12 User manual

Double Swing 1 toddler seat H2.12
BBPE030.4K
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 030 4K
Dubbele schommel pz
Boer Basic play
27-1-2015
BOER
SPEELTOESTELLEN
Hoofdafmetingen Main dimensions
0,00 m
2,04 m
2,19 m
0,00 m
0,64 m
0,70 m
0,75 m
1,40 m
0,00 m 0,43 m 1,10 m 2,24 m 2,91 m 3,34 m
>0,35 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 030 4K
Dubbele schommel pz
Boer Basic play
27-1-2015
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
7,28 m 6,28 m
4,00 m
3,00 m
2,00 m
36403640

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 030 4K
Dubbele schommel pz
Boer Basic play
27-1-2015
BOER
SPEELTOESTELLEN
odemplan Groundplan
Grondmarkering
Ground le el marker
0,53 m
2,86 m1,55 m2,86 m
0,30 m 3,40 m 0,30 m
0,30 m
0,33 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 030 4K
Dubbele schommel pz
Boer Basic play
27-1-2015
BOER
SPEELTOESTELLEN
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
Boer Basic playSchommel
AK511BBPMOD11
Ketti g 1,45 m
Schommelzitje
A
103371
FRP
MOD
1
2
Ketti g 35 cm
Peuterzitje
105371
FRP
MOD13
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Bouw 1 op uit de staanders en ligger
3 - Plaats 2 en 3, verbind deze aan 1
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Assemble 1 out of the posts and horizontal beam
3 - Place 2 and 3, attach them to 1
4 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
1
2
3
Typeplaatje
Identification plate
B

LOGBOOK
Type indication Basic Play
Article number BBPE030.4K
Product Name Double Swing 1 toddler seat H2.12
Maximum fall height 1,3 m
Construction year 2023
Certificate 139850
Inspection body Keurmerkinstituut
Groeneweg 2e, Zoetermeer
2718AA Zoetermeer
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 511 K A
Schommel
Boer Basic play
10-10-2017
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
5 x 50 - RVS A2-70
Schroef Assy
050005002BSR161
5 x 50 - VZ 8.8
Schroef
050005002BSV42
10 - VZ 8.8
Zeskantmoer
008010017BSV163
10 x 145 - VZ 8.8
Slotbout
145010026BSV124
10 x 135 - VZ 8.8Slotbout 135010026BSV
45
10 VZSLUITRING 002010030BSV166
10 - VZ 8.8Veerring 002010034BSV167
Basic PlayStaander schommel
027BBPKST48
Donut wit
Beschermdop 10- 12
020010DONKST169
Dop wit
Beschermdop 10- 12
020010DOPKST1610
AluminiumPaalkap 100x100
B
502100
KAP
O E
4
11
100 x 100VoetplaatC
VZP
903
VRB
O E
4
12
Basic PlaySchommelpaneel
A
061007
BBP
OPE213
Basic playBovenbalk schommel
A
010
BBP
S E114
13
1
12
8
2
14
43679 10
5 3 67 9 10
11

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD FRP 371 103 A
Schommelzitje
Ketting 1,45 m
4-11-2013
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr.
M10 - RVS A2-70
Borgdo moer
020010011BSR41
M10 x 120 - RVS A2-70
Zeskantbout
120010021BSR42
M10SLUITRING 002010030BSR83
RVS A2-70
Schommelscharnier
091012081BSR2
4
Donut zwart
Beschermdo M10-M12
060010DONKST45
Do zwart
Beschermdo M10-M12
060010DOPKST46
Galileo VVul laat
POM006SOLKST47
Zitje incl. ketting
090
145ZIT
SMD
1
8
Met vork 1,45 mSchommelketting 5mm
145005
KETRNT
28.1
Zwart
Schommelzitje CNK 090001
ZIT
CNK
1
8.2
M8 x 25 - RVS A2-70Zeskantbout 025008021BSR
4
8.3
M8 - RVS A2-70
Sluitring
002008030BSR
4
8.4
2
6
3
5
3
1
8.2
7
7
4
8.1
8.4
8.3

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD FRP 371 105
Peuterzitje
Ketting 35 cm
6-8-2014
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
BORG RVS M10DOPMO R 020010011BSR
4
1
M10 x 120 - RVS A2-70
Zeskantbout
120010021BSR42
M10SLUITRING 002010030BSR43
6 mm - RVS A2-70Ketting 350mm 000006050BSR24
RVS A2-70
Schommelscharnier
091012081BSR2
5
Peuterzitje
Peuterschommel
A
001HUC
DRD
16
Donut zwart
Beschermdop M10-M12 060010DONKST
47
Dop zwart
Beschermdop M10-M12 060010DOPKST
4
8
Galileo VVulplaat
POM006SOLKST
4
9
6
4
1 3
2 7
9
5
Powered by TCPDF (www.tcpdf.org)