BOERPLAY Climbing/Tumble Bars Trio H1.17-1.03-1.17 User manual

Climbing/Tumble Bars Trio
H1.17-1.03-1.17
SOLE030.222
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 222
Klimduikel trio
Pionier
25-7-2019
Afmetingen Dimensions
0,97 m
1,07 m0,97 m1,07 m
0,00 m
0,24 m
0,45 m
0,60 m
0,79 m
0,94 m
1,03 m
1,17 m
1,35 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 222
Klimduikel trio
Pionier
25-7-2019
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
4,20 m
3,20 m
3,00 m
R1,50m
R1,50m
0,70 m
6,18 m
3,70 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 222
Klimduikel trio
Pionier
25-7-2019
Bodemplan Groundplan
0,60 m
rondmarkering
Ground le el marker
6,18 m
4,20 m
R1,50m
R1,50m
4,20 m
0,20 m
0,49 m
3,80 m
0,06 m
0,64 m 1,18 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 222
Klimduikel trio
Pionier
25-7-2019
Modules Modules
OpmerkingBenamingRev.Bew.Volgnr.Progr.Type
#
Nr.
115 cm
Duikelrek 000500
PNR
MOD2
1
Pionier
Duikelstang 100 cm 000502
PNR
MOD
1
2
Pionier
Duikelstang 98 cm
00050
PNR
MOD2
1233
Geleverde modules:
Zie tabel
Montageinstructie:
- De oofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens et bodemplan
2 - Plaats 1 en 1
3 - Verbind 1 en 1 met 2 en 2x 3
4 - Controleer of et toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dic t de gaten en verdic t et zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. et toestel
Supplied modules:
See table
Assembly instruction:
- T e main dimensions indicate t e dimensions of t e posts and floors
- T e detailed dimensions s ow t e specific dimensions of t e connections
- T e modules w ic contain tubes are dimensioned at t e top of t e flanges
- Ot er modules are dimensioned at t e top (climbing walls, caps for t e posts, etc.)
Assembly sequence:
1 - Dig t e oles according to t e ground plan
2 - Place 1 and 1
3 - Connect 1 and 1 wit 2 and 2x 3
4 - C eck t at t e equipment conforms to t e dimensions s own on s eet 'dimensions'
5 - Close t e oles and compact t e sand
C ecks:
1 - Correct assembly and all t e fasteners
2 - C eck t e dimensions of t e safety area wit regard to t e play equipment
Typeplaatje
Identification plate
B

LOGBOOK
Type indication Pionier
Article number SOLE030.222
Product Name Climbing/Tumble Bars Trio H1.17-1.03-1.17
Maximum fall height 1,2 m
Construction year 2024
Certificate 09100312703
Inspection body Liftinstituut B.V.
Buikslotermeerplein 381, A'dam
1025 XE Amsterdam
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

v LTFTTNSTTTUUT
CERTI FICAAT VAN TYPEONDERZOEK
lngevolge het Warenwetbesluit Attractie- en Speeltoestellen afgegeven door het Liftinstituut B.V.
aangewezen bij Besluit no. VGP/PSL 2857566 van27 juniZ0OB
Certificaat nr. :
Productomschrijving :
Fabrikaat, typeaanduiding :
Naam en adres fabrikant :
Naam en adres :
houder van het certificaat
Certificaat afgegeven :
volgens het volgende
voorschrift
Keuringslaboratorium :
Datum en nummer van het
Keuringslaboratoriu m-
Rapport
Datum van typeonderzoek :
Bijlagen bij dit certificaat :
Eventuele aanvullende :
opmerkingen
Conclusie
Gedaan te Amsterdam
Datum van afgifte:7 april2009
R
PflOOlJ[Is
fltlA [ ût7
NL 09-1003-1 27-03 Object nr. 100312703
Duikelrekken met duikelstangen, rekstokken en klimrekken
op basis van het programma Pionier
TOE SOL: 030 215, 030 220, 030 221, 030 222, 030 225,
030 226, 030 227, 030 230, 030 231, 030 232
Speelwijzer
Nijverheidstraat B
5317 NL Nederhemert Noord
Speelwijzer
Nijverheidstraat B
5317 NL Nederhemert Noord
Warenwetbesluit attractie- en speeltoestellen
Geen
: Geen
Periode 13 oktober 2008 t/m 19 januari 2009
Verslag behorende bij het certificaat van type onderzoek
nr.: NL 09-1003-1 27-03
Geen
Het toestel voldoet aan de bepalingen van het
Warenwetbesluit attractie- en speeltoestellen met
inachtneming van de bovengenoemde evêñtuele aanvullende
opmerkingen
LIFTINSTITUUT B.V.
Senior Officer Certification
& Technology
* Liftinstituut B.V. . Buikslotermeerplein 381 " Postbus 36027 . 1020 MA Amsterdam *
* www.liftinstituut.nl "

B
BB
Be
ee
en
nn
na
aa
am
mm
mi
ii
in
nn
ng
gg
g
Title
O
OO
Op
pp
pm
mm
me
ee
er
rr
rk
kk
ki
ii
in
nn
ng
gg
g
Comment
D
DD
Da
aa
at
tt
tu
uu
um
mm
m
Date
T
TT
Te
ee
ek
kk
ke
ee
en
nn
ni
ii
in
nn
ng
gg
g
Drawing
MOD PNR 500 000
Duikelrek
115 cm
9-10-2008
BOER
S
SS
SP
PP
PE
EE
EE
EE
EL
LL
LT
TT
TO
OO
OE
EE
ES
SS
ST
TT
TE
EE
EL
LL
LL
LL
LE
EE
EN
NN
N
Samenstelling module Assembly module
115 cm
Duikel frame
A320201PNRSME
1
2
E 05
Submodule
000005PNRSMD21
OPMERK NGBENAM NG
RBEH.
NR.PROJ.
TYPE
NPOS
1
2
1,17m
Grondmarkering
Ground level marker

B
BB
Be
ee
en
nn
na
aa
am
mm
mi
ii
in
nn
ng
gg
g
Title
O
OO
Op
pp
pm
mm
me
ee
er
rr
rk
kk
ki
ii
in
nn
ng
gg
g
Comment
D
DD
Da
aa
at
tt
tu
uu
um
mm
m
Date
T
TT
Te
ee
ek
kk
ke
ee
en
nn
ni
ii
in
nn
ng
gg
g
Drawing
MOD PNR 502 000
Duikelstang 100 cm
Pionier
3-10-2008
BOER
S
SS
SP
PP
PE
EE
EE
EE
EL
LL
LT
TT
TO
OO
OE
EE
ES
SS
ST
TT
TE
EE
EL
LL
LL
LL
LE
EE
EN
NN
N
Samenstelling module Assembly module
EI 05Submodule 000005
PNR
S D22
Lengte 1020 cm HOHKlimstang PNR 33.7x2 102130
PNR
O E
11
OP ERKINGBENA ING
RBEH.NR.
PROJ.
TYPEN
POS
21

B
BB
Be
ee
en
nn
na
aa
am
mm
mi
ii
in
nn
ng
gg
g
Title
O
OO
Op
pp
pm
mm
me
ee
er
rr
rk
kk
ki
ii
in
nn
ng
gg
g
Comment
D
DD
Da
aa
at
tt
tu
uu
um
mm
m
Date
T
TT
Te
ee
ek
kk
ke
ee
en
nn
ni
ii
in
nn
ng
gg
g
Drawing
MOD PNR 503 000
Duikelstang 98 cm
Pionier
6-10-2008
BOER
S
SS
SP
PP
PE
EE
EE
EE
EL
LL
LT
TT
TO
OO
OE
EE
ES
SS
ST
TT
TE
EE
EL
LL
LL
LL
LE
EE
EN
NN
N
Samenstelling module Assembly module
EI 05Submodule 000005
PN
SMD22
Lengte 1000 cm HOHKlimstang PN 33.7x2 100130
PN
OME
11
OPME KINGBENAMING
BEH.N .
P OJ.
TYPEN
POS
2
1
Powered by TCPDF (www.tcpdf.org)