BOERPLAY SOLE030.106 User manual

SOLE030.106
Metal swing with bird's nest

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 106 B
Swoeng metal
Vogelnest
15-12-2014
Hoofdafmetingen Main dimensions
4,42 m
2,18 m
0,00 m
>0,40 m
2,56 m
2,81 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 106 B
Swoeng metal
Vogelnest
15-12-2014
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
7,44 m
5,35 m (t.b.v. plaatsen)
2,25 m
7,80 m 6,80 m
3,21 m (t.b.v. plaatsen)
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 106 B
Swoeng metal
Vogelnest
15-12-2014
odemplan Groundplan
0,62 m
2,64 m 2,52 m 2,64 m
4,75 m
0,50 m o
Grondmarkering
Ground le el marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 106 B
Swoeng metal
Vogelnest
15-12-2014
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
SchommelzitjeVogelnest 1,0 m
B
380030SOLMO
11
Metal dubbelSchommelframe
A
001368SOLMO12
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Paats 2
3 - Bevestig 1 aan 2
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 2
3 - Attach 1 to 2
4 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
2
1

LOGBOOK
(Onderstaand logboek kan gebruikt worden om te voldoen aan de eisen, gesteld in artikel 14 van het Warenwetbesluit Attractie- en Speeltoestellen)
Type indication Classic Play
Product code SOLE030.106
Name of equipment Vogelnestschommel metaal
Maximum height of fall 1,5 m
Year of construction 2017
Certificate 09200116202
inspection authority Liftinstituut B.V.
Buikslotermeerplein 381, A'dam - 1025 XE Amsterdam
Name manufacturer BOERplay
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
name installer
Description of equipment Metal swing with bird's nest
Location of equipment
Data about the owner of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
Data about the administrator of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
SOLE030.106
Metal swing with bird's nest

LOGBOOK
Inspection and maintenance intervals
Nr.
Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and missing parts.
Inspect bolts, screws and nuts for absence, jams, corrosion
and wear.
Add missing parts, secure joints, apply missing fixing
agent and replace corroded parts.
1
2
Chec suspension for wear. Replace worn parts and/or remove non-functioning
parts.
1
3
Inspect rotating parts such as hinges, rolling-element
bearings, etc. for wear and acceptability.
Replace worn parts and/or remove non-functioning
parts.
1
4
Chec wood for splinters, unacceptable damage and signs of
rot. Especially at ground level.
Repair damage. Replace affected wood. Smoothen
splintered wood and sharp edges.
1
5
Inspect foundation for stability, tearing and coverage. Restore foundation and covering material.
3
6
Examine rubber and synthetic parts for wear, damage and
brea . Replace original parts.
3
7
Inspect metal for corrosion and damage in the coating. Restore any damaged coating (after removing rust and
applying primer).
6
Chec ropes, cables, chains and nets for wear and damage.
Steel cables and nets which are tensioned must be chec ed
for tension.
Replace parts where necessary. Steel cables and nets
must be tensioned.
3
9
Inspect equipment for unsafe changes and additions. Remove unsafe additions and correct unsafe changes.
1
10
Inspect safety surfaces. Restore and repair where necessary.
1
Remarks
1. If used intensively, all points require extra attention.
2. Extreme weather conditions and locations may require a higher inspection frequency. Discuss this with
the supplier.
3. Vandalism-sensitive locations require stricter inspections, possibly daily.
4. Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly.
Examples are poisonous plants, glass shards, etc. Frequency depends on strain.
5. Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area.
6. Replacement parts can be ordered at the manufacturer with the part numbers on the module drawing.
Drawings can be found in de user guide.
7. The impact area shall be provided with impact attenuating surface according to the specified falling
height.
. This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7".

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 030 549 A
Vogelnest Schommelzit
Nest Ø1,0m Ketting 2,0 m
24-2-2017
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
BORG RVS M10DO MOER 020010011BSR
4
1
M10 x 130 - RVS A2-70
Zeskantbout
130010021BSR42
M10SLUITRING 002010030BSR83
5 mm, RVS A2-70
D-Sluiting
000005031BSR44
RVS A2-70
Scharnier dubbel NORMAAL
092012081BSR2
5
balk 2,5 mVogelnest Ø1,0 m
100001NST
DRD
16
0,18 m langRVS ketting 5mm 018002005
KET
2
7
Donut zwart
Beschermdop M10-M12 060010DONKST
4
8
Dop zwart
Beschermdop M10-M12
060010DOKST
4
9
6
2
9
3
8
3
1
Hoek ketting > 60° (ketting niet strak)
Opening altijd < 157x89 mm
7
4
4

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 368 001 A
Schommelframe
Metal dubbel
12-10-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
M10 - RVS A2-70
Borgmoer
010010010BSR21
BORG RVS M10DOPMOER 020010011BSR2
M10 x 30 - RVS A2-70
Zeskantbout
030010021BSR23
M10 x 105 - RVS A2-70
Zeskantbout
105010021BSR4
M10SLUITRING 002010030BSR20
5
M10 - VZ .
Borgmoer
010010010BSV
4
6
M10 x 100 - VZ .
Zeskantbout ISO 4014
100010021BSV47
M10 VZSLUITRING 002010030BSV
Donut RoodBeschermdop M10-M12
030010DONKST129
Dop roodBeschermdop M10-M12
030010DOPKST1210
UkkepukVoetplaat
BVZP
615
UKP
OME
4
11
DUBBEL ROODSCHOMMELBUIS
D
37204SOLSME
1
12
Schommel gecoatStaander links
D
372050SOLSME213
Schommel gecoatStaander rechts
D
372051SOLSME214
12
13
14
3
10
5
9
9
5
1
10
4
10
5
9
5
2
11
7
8
8
6