BOERPLAY Springer Swan User manual

Springer Swan
BBPE011.4K
Powered by TCPDF (www.tcpdf.org) 1 / 1

© Copyright BOERplay 4-8-2021 Revision: A BBP 011 4K
main dimensions
Hoofdafmetingen
Hauptabmessungen
Dimensiones principales
Dimensions principales
NL
DE
ES
FR
0,67 m
0,37 m
0,84 m

© Copyright BOERplay 4-8-2021 Revision: A BBP 011 4K
obstacle free zone
Obstakelvrije zone
Hindernissfreie raum
Zona libre de obstáculos
Zone libre d’obstacles
NL
DE
ES
FR
3,50 m n

© Copyright BOERplay 4-8-2021 Revision: A BBP 011 4K
ground plan
Bodemplan
Bodenplan
Plan de superficie
Plan de surface
NL
DE
ES
FR
1,75 m 1,75 m
0,49 m
Grondmarkering
Ground level marker
1,75 m1,75 m
0,48 m o

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
Onderstel
Veerwip 715BBIMOD11
Hobbel
ZwanenAK
598
BBP
MOD
1
2
HobbelHand reep
K
600
BBP
MOD23
© Copyright BOERplay 4-8-2021 Revision: A BBP 011 4K
order of assembly
Montagevolgorde
Montagereihenfolge
Orden de esemblado
Ordre de montage
NL
DE
ES
FR
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zijn bemaat op de bovenkant (klim anden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats het geassembleerde toestel
3 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
4 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbou en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions sho the specific dimensions of the connections
- The modules hich contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing alls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place the assembled unit
3 - Check that the equipment conforms to the dimensions sho n on sheet 'dimensions'
4 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area ith regard to the play equipment
1
3
2
3
Typeplaatje
Identification plate
B

LOGBOOK
Type indication Basic Play
Article number BBPE011.4K
Product Name Springer Swan
Maximum fall height > 0,6 m
Construction year 2023
Certificate 138144
Inspection body Keurmerkinstituut
Groeneweg 2e, Zoetermeer
2718AA Zoetermeer
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

© Copyright BOERplay 12-1-2022 Revision: MOD BBI 715
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR

© Copyright BOERplay 12-1-2022 Revision: MOD BBI 715
BSV.010.010.010
x
3
BSV.026.010.035
x
3
BSV.030.010.002
x
3
OME.MNP.212.905
x
1
SMD.VER.200.905
x
1
SME.MNP.149.372
x
1
1/1
SMD.VER.200.905
BSV.026.010.035
OME.MNP.212.905
BSV.010.010.010
BSV.030.010.002
SME.MNP.149.372

© Copyright BOERplay 4-8-2021 Revision: A MOD BBP 598 K
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
M10 - VZ 8.8Borgdopmoer 020010011BSV
41
M10ZESKANT MOER 008010017BSV
4
2
M10x35S OTBOUT 035010026BSV43
M10 x 40 - VZ 8.8
Slotbout
040010026BSV44
M10 VZS UITRING 002010030BSV85
M10 - VZ 8.8
Veerring
002010034BSV
4
6
84395000012
interplay donut M10 wit
020011DONKST
47
84395000014
interplay dop M10 wit
020011DOPKST48
mini play Hoekje
905209MNPOME49
Rechts
Zwaan B006129BBPOPE110
inks
ZwaanB
006130
BBP
OPE
111
Hobbel
Zitje
090139
BBP
OPE
1
12
10
11
351
4
7
5
6
2
8
12
9

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 600 K
Handgreep
Hobbel
13-2-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
M10 - VZ 8.8
Zeskantmoer
008010017BSV21
M10 VZSLU TR NG 002010030BSV22
M10 - VZ 8.8
Veerring
002010034BSV23
M10 x 365 - VZ 8.8
Draadeind
365010060BSV1
4
84395000012interplay donut M10 wit 020011DONKST
45
84395000014interplay dop M10 wit 020011DOPKST26
Ø24x2 L=295
Buis staal blauw
502231
MNP
OME1
7
61 3 2 5 45 7
Powered by TCPDF (www.tcpdf.org)