BOERPLAY VRBE006.014 User manual

VRBE006.014
Multi Swing

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE VRB 006 014 A
Multi Swing
Combi Schommel
16-12-2014
Afmetingen Dimensions
0,00 m
2,30 m
2,40 m
2,55 m
> 0,40 m
> 0,35 m
2,14 m
6,78 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE VRB 006 014 A
Multi Swing
Combi Schommel
16-12-2014
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
5,71 m
7,80 m
3,22 m
7,78 m
6,80 m
6,80 m 7,80 m
9,79 m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE VRB 006 014 A
Multi Swing
Combi Schommel
16-12-2014
Bodemplan Groundplan
0,71 m
2,89 m
2,03 m2,89 m
0,56 m 3,35 m 3,63 m 0,25 m
0,30 m
0,26 m
0,42 m
0,37 m
rondmarkering
Ground le el marker
0,82 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE VRB 006 014 A
Multi Swing
Combi Schommel
16-12-2014
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
Ketting 180Overgooi ZitjeC502481SOMOD21
Eind ModuleMulti Swing, RVS
B
502493SOMOD22
Tussen ModuleMulti Swing, RVS
B
502494SOMOD13
Dubbele Schommel StangMulti Swing
A
502495SOMOD
14
Vogelnest StangMulti Swing 496030SOMOD
15
Overgooi VogelnestMulti Swing,
C502497SOMOD16
21413 26 5
Typeplaatje
Identification plate
B
Geleverde modules:
Zie tabel
ontageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
ontagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats 2,3
3 - Plaats 1(2x),4 en verbind deze aan 2,3
4 - Plaats 2
5 - Plaats 5,6 en verbind deze aan 2,3
6 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
7 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 2,3
3 - Place 1(2x),4 and attach it to 2,3
4 - Place 2
5 - Place 5,6 and attach it to 2,3
6 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
7 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment

LOGBOOK
(Onderstaand logboek kan gebruikt worden om te voldoen aan de eisen, gesteld in artikel 14 van het Warenwetbesluit Attractie- en Speeltoestellen)
Type indication Nature Play
Product code VRBE006.014
Name of equipment Multi Swing RVS
Maximum height of fall 1,5 m
Year of construction 2017
Certificate 100326978
inspection authority Liftinstituut B.V.
Buikslotermeerplein 381, A'dam - 1025 XE Amsterdam
Name manufacturer BOERplay
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
name installer
Description of equipment Multi Swing
Location of equipment
Data about the owner of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
Data about the administrator of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
VRBE006.014
Multi Swing

LOGBOOK
Inspection and maintenance intervals
Nr.
Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and missing parts.
Inspect bolts, screws and nuts for absence, jams, corrosion
and wear.
Add missing parts, secure joints, apply missing fixing
agent and replace corroded parts.
1
2
Chec suspension for wear. Replace worn parts and/or remove non-functioning
parts.
1
3
Inspect rotating parts such as hinges, rolling-element
bearings, etc. for wear and acceptability.
Replace worn parts and/or remove non-functioning
parts.
1
4
Chec wood for splinters, unacceptable damage and signs of
rot. Especially at ground level.
Repair damage. Replace affected wood. Smoothen
splintered wood and sharp edges.
1
5
Inspect foundation for stability, tearing and coverage. Restore foundation and covering material.
3
6
Examine rubber and synthetic parts for wear, damage and
brea . Replace original parts.
3
7
Inspect metal for corrosion and damage in the coating. Restore any damaged coating (after removing rust and
applying primer).
6
Chec ropes, cables, chains and nets for wear and damage.
Steel cables and nets which are tensioned must be chec ed
for tension.
Replace parts where necessary. Steel cables and nets
must be tensioned.
3
9
Inspect equipment for unsafe changes and additions. Remove unsafe additions and correct unsafe changes.
1
10
Inspect safety surfaces. Restore and repair where necessary.
1
Remarks
1. If used intensively, all points require extra attention.
2. Extreme weather conditions and locations may require a higher inspection frequency. Discuss this with
the supplier.
3. Vandalism-sensitive locations require stricter inspections, possibly daily.
4. Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly.
Examples are poisonous plants, glass shards, etc. Frequency depends on strain.
5. Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area.
6. Replacement parts can be ordered at the manufacturer with the part numbers on the module drawing.
Drawings can be found in de user guide.
7. The impact area shall be provided with impact attenuating surface according to the specified falling
height.
. This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7".

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 030 496
Multi Swing
Vogelnest Stang
19-10-2011
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
OPMERKINGBENAMINGRBEH.NR.PROJ.TYPENPOS
UBP Schommel dubbelBovenbuis
D011200UBPOM11
Overgooi Schommel
Lagerring met gatA
006200
UBP
KST22

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 481 502 C
Overgooi Zitje
Ketting 180
12-10-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr.
M10 - RVS A2-70Borgmoer 010010010BSR21
M10 x 70 - RVS A2-70
Zeskantbo t
070010021BSR22
M10SLUITRING 002010030BSR63
RVS A2-70Schommelscharnier 090012081BSR2
4
Don t zwart
Beschermdop M10-M12
060010DONKST
45
Dop zwart
Beschermdop M10-M12
060010DOPKST46
UBP Schommel
LagerringA005200UBPKST27
Zitje incl. ketting
090180ZITSMD18
Met vork 1,80/1,75 mSchommelketting 5mm
180005
KETRNT
28.1
Zwart
Schommelzitje CNK
090001
ZIT
CNK18.2
M8 x 25 - RVS A2-70Zeskantbo t 025008021BSR
4
8.3
M8 - RVS A2-70Sl itring 002008030BSR
4
8.4
Schommel d bbelUBP Schommelb is
D
502200
UBP
SME19
6235
6
1
3
5
7
9
4
7
8.3
8.4
8.2
8.1

A ( 1 : 10 )
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 493 502 B
Multi Swing, RVS
Eind Module
13-10-2017
Samenstelling module Assembly module
A A
OpmerkingBenamingRev.Bew.Volgnr.Progr.Type
#
Nr.
M10 - RVS A2-70Borgmoer 010010010BSR81
M10 x 120 - RVS A2-70Zes antbout 120010021BSR22
M10 x 120 - RVS A2-70
Slotbout
120010026BSR63
M12 verzin tBorgdopmoer
025012011BSV24
M12 x 120
Zes antbout ISO 4014
120012021BSV25
M12 - VZ 8.8
Sluitring
003012030BSV46
Donut zwart
Beschermdop M10-M12
060010DONKST6
7
Dop zwart
Beschermdop M10-M12
060010DOPKST68
100 x 100VoetplaatC
VZP
903
VRB
OME29
ovg schommelrechte verbinding
A
502255SOLSME
1
10
OvergooischommelStaander
320654
VRB
SME211
104 5
Grondmarkering
Ground level marker
0,70 m 2,30 m
9
21
3
67 8
11

B ( 1 : 15 )
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 494 502 B
Multi Swing, RVS
Tussen Module
13-10-2017
Samenstelling module Assembly module
A A
OpmerkingBenamingRev.Bew.VolgnrProgr.Type
#
Nr
M10 - VZ 8.8Borgmoer 010010010BSV81
M12 ver inktBorgdopmoer 025012011BSV
4
2
M10 x 120 - VZ 8.8
Zeskantbout ISO 4014
120010021BSV23
M12 x 120
Zeskantbout ISO 4014
120012021BSV44
M10 x 120 - VZ 8.8
Slotbout
120010026BSV65
M12 - VZ 8.8
Sluitring
003012030BSV86
Donut wart
Beschermdop M10-M12
060010DONKST6
7
Dop wart
Beschermdop M10-M12
060010DOPKST68
100 x 100VoetplaatC
VZP
903
VRB
OME29
Multi SwingTussenverbinding
A
502258SOLSME
1
10
OvergooischommelStaander
320654
VRB
SME211
9
10
5
2,30 m
0,78 m
11
4662
8
Grondmarkering
Ground level marker
7
3 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 495 502 A
Multi Swing
Dubbele Schommel Stang
13-10-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
Overgooi Schommel
Lagerring met gatA
006200
U P
KST2
1
U P Schommel
LagerringA
005200
U P
KST22
U P Schommel dubbelMiddenbuis
D502042U POME13
U P Schommel dubbelovenbuis
D
011200
U P
OME
14
3
2
4
1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 497 502 C
Multi Swing,
Overgooi Vogelnest
13-10-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
5 mm, RVS A2-70
D-Sluiting
000005031BSR
4
1
RVS A2-70
S harnier dubbel NORMAAL
092012081BSR22
M10 - VZ 8.8
Borgdopmoer
020010011BSV43
M10 x 25 - VZ 8.8
Zeskantbout ISO 4014
025010021BSV44
M10 VZSLUITRING 002010030BSV8
5
balk 2,5 mVogelnest Ø1,0 m
100001NST
DRD
16
0,18 m langRVS ketting 5mm 018002005
KET
2
7
UBP S hommel
LagerringA
005200
UBP
KST28
TBV Vogelnest
Overgooi Buis
A
502228SOLSME19
4
5
5
3
8
6
7
1
1
2
9
Hoek ketting > 60° (ketting niet strak)
Opening altijd < 157x89 mm